Edlund ERS-300 Manual

Edlund Vægt ERS-300

Læs gratis den danske manual til Edlund ERS-300 (3 sider) i kategorien Vægt. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Edlund ERS-300, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

- 1 - 05/09

Edlund Company, 159 Industrial Parkway, Burlington, VT 05401 802-862-9661 www.edlundco.com

Electronic Receiving Scales

MODEL ERS-60/150/300

Capacity Model ERS-60 (60.0 lbs. X 0.25 ozs., 30.0 Kg X 5 G)

Model ERS-150 (150.0 lbs. X 0.05 lbs., 75.0 Kg X 0.02Kg)

Model ERS-300 (300.0 lbs X 0.1 lbs., 150.0 Kg X 0.05 Kg)

Platform Size Model ERS-60/150 (12" X 12-1/2 )"

Model ERS-300 (19-3/4" X 25-3/4 )"

Overall Size Model ERS-60/150 (12"X 12-1/2 X 2-1/2 )" "

Model ERS-300 (19-3/4 X 25-3/4" " X 4 ")

Power Source 120 VAC, 60 HZ/230 VAC, 50 HZ Output: 12VDC 1000ma

-Not Legal for Trade –

Operating instructions:

The ERS model scale operates on 6xAA batteries, or a 9-volt power supply (part #PS5005). The scale has an

automatic power off feature. (Which can be programmed to 120 sec., 240 sec., 360 sec., 720 sec., or off) If a

battery is used, the scale will shut off after the programmed time if no weighing operation is performed.

To install the batteries, turn the scale display over, open the battery box, install 6xAA batteries (observing

polarity), and close the cover. If the power supply is used, push the power supply tip into the jack orifice,

making sure the two pieces are properly aligned for a tight seal.

Turn on the scale by depressing the "on/off" switch. Scale readout will show all 8's for approximately 5

seconds and then the zero reading. If the scale is overloaded, a series of horizontal lines will be displayed. If

a load is placed on the scale platform, the weight of this load is shown on the scale display in the units in

which the scale is weighing. You can change the weighing mode by pressing the "Hold/Mode" button.

This load can now be "tared out" i.e. shown as zero on the scale display, by depressing the "Tare" button. If

an additional load is then placed on the platform, the weight of this additional load can also be "tared out" by

depressing the "Tare" button. This tare operation can be repeated up to the capacity of the scale.

If the total load is now removed from the platform, the weight of the total load will be shown as a negative

value on the scale display. This negative value can now be removed from the display by depressing the

"Tare" button. Depressing the "on/off' button at any time will turn the scale off.

To use the "Hold" button, place weight on the platform, then press the "Hold" button until the weight starts

blinking. Release the button, and remove the weight from the platform the display. The values will still show

the amount that was on the platform. To remove, just press the "Tare" button and the display returns to zero.

I130

- 2 - 05/09

Other Scale Options

To enter the calibration mode, perform the following steps:

1) With the scale in the off position, press and hold both the "TARE" and "HOLD/MODE" keys, and

then press the "ON/OFF" key, the display shows "CAL".

2) Press the "TARE" key and the display will read "CAL 0".

3) Press the "TARE" key once, or wait a few seconds and the correct calibration weight appears and

flashes on the display (ERS-60 is 10.0 Kg / ERS-150 is 25.0 Kg / ERS-300 is 50.0 Kg)

4) Place the correct calibration weight gently on the platform. When calibration is complete, the scale

will briefly display "CAL F" and then return to the weighing mode. You may re-zero the scale by

pressing the "TARE" key.

If no weight is placed on the platform the scale will return to the normal weighing mode after 15 seconds. Note:

If "CAL E" appears, this indicates that a calibration error has occurred and the calibration process must be

repeated. "CAL E" can occur when the calibration steps are not followed in the correct order or due to the

addition of an incorrect calibration weight. "CAL E" will remain on the display until the scale is shut off

using the "ON/OFF" key and the scale will revert to the previous calibration settings. The calibration

procedure must be repeated in order to change the scale calibration settings.

Procedure for units disabling:

The Model ERS-60 scale will weigh in the following two units: lb.-decimal oz.,

& grams,. The ERS-150/300

scales will weigh in the following two units: lbs & Kilograms. You can disable some of these weighing

modes by using the buttons on the keypad. To do so the following procedure will be used:

1) With the scale in the off position, press and hold both the "TARE" and "HOLD/MODE" buttons,

and then press the "ON/OFF" button, the display shows "CAL".

2) Press the "HOLD/MODE” button once and "UNIT" is shown on the display.

3) Press the "TARE" button until the unit type that you wish to disable is shown on the display.

4) Press the "HOLD/MODE" button to disable the unit displayed. The display will show "OFF" and the

next weighing mode will be displayed.

5) Repeat steps 3 & 4 for the other units that you want to disable.

6) Before the scale is turned off, the scale must be programmed to set the mode or units that you want to

show when the scale is first turned on. (If you are only using one weighing unit, disregard this step.)

Using the "TARE" button, select a weighing mode or units to be shown first when the scale is turned

on.

7) Press and hold the "TARE" button and then press the "HOLD/MODE" button and the display will

show "END" and automatically return to the weighing mode.

8) Shut the scale off and turn it back on again using the "ON/OFF" button, the scale will start in

the weighing mode or unit that was selected in the previous step.

9) If you wish to change the units that are disabled, repeat steps 1thru 8.

10) If you wish to have all the units be displayed, repeat step 1 and then steps 6 thru 9.

Produkt Specifikationer

Mærke:	Edlund
Kategori:	Vægt
Model:	ERS-300

Har du brug for hjælp?

Hvis du har brug for hjælp til Edlund ERS-300 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vægt Edlund Manualer

Edlund ERS-300 Manual

13 Juni 2025

Edlund ERS-150 Manual

13 Juni 2025

Edlund ERS-60 Manual

12 Juni 2025

Vægt Manualer

Nyeste Vægt Manualer

Kern MAP 80K1 Manual

27 September 2025

Kern HCN 200K500IP Manual

26 September 2025

Kern HCN 50K100IP Manual

26 September 2025

26 September 2025

26 September 2025

24 September 2025

24 September 2025

Brecknell MBS600 Manual

23 September 2025

Brecknell MS1000-LCD Manual

23 September 2025

Electrolux M2GCP101 Manual

23 September 2025