Elektrobock BT012 Manual

Elektrobock Termostat BT012

Læs gratis den danske manual til Elektrobock BT012 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 75 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 38 anmeldelser. Har du et spørgsmål om Elektrobock BT012, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

LEAD FREE

in compliance with s RoHS

In case of guarantee

or post-guarantee

service, send the

thermostat to the

distributor’s or manu-

facturer’s address.

CERTIFICATE OF GUARANTEE

(guarantee period for the product amounts to 2 years)

product No.:

date of sale:

stamp of shop:

examined by:

MADE IN CZECH REPUBLIC

BT012

WIRELESS ROOM THERMOSTAT

with simple operation

and a wall-mounted receiver

The great advantage is the two-way communication, quick setting and change of the required

temperature by simply turning the knob on the transmitter. The transmitter is portable, or it can be

installed on the wiring box in the reference room. The receiver is equipped with the code self-

learning system and the E-EPROM memory, which preserves the saved code even at power

failure. The wireless version enables simple and quick installation; therefore, there is no need for

laborious and time-consuming installation of a line between the thermostat and boiler with

penetration through ﬂ oors. The coverage of the set can reach up to 35 m.

• Receiver power supply 230 V/ 50 Hz.

• Receiver with the CODE SELF-LEARNING

system and the E-EPROM memory (saving

the code even at power failure).

• Two-wire connection to the boiler.

• Indication LED for signalization of the

states

- power supply indication

- failure state

- relay closed.

receiver - wall-mounted

transmitter

• Simple control element for temperature

setting – knob.

• Indication of the boiler switching and error

states by means of a red LED.

•Night attenuation – button for quick

selection of the night attenuation

(automatic decline by 3 °C for the 8-hour

period).

• Anti-freeze temperature .

• Optional internal frame of a different colour

can be bought (according to the sampler at

www.elbock.cz) for a perfect harmony in

the interior.

ELEKTROBOCK CZ s.r.o.

Blanenská 1763

Kuřim 664 34

Tel.: +420 541 230 216

EU DECLARATION OF CONFORMITY

Hereby, ELEKTROBOCK CZ s.r.o. declares that

the radio equipment type BT012 is in compliance

with Directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the following

internet address: www.elbock.cz

TECHNICAL PARAMETERS

IMPORTANT INFORMATION

TWO-WAY COMMUNICATION

- Providing for reliable signal transmission

and enabling return information acquisition

www.elbock.cz

Receiver

Power supply 230 V/ 50 Hz

Communication type two-way

Frequency 433.92 MHz

Range

200 m

(free area)

25 m (built-up area)

Sensitivity < -952 dBm

Output relay, max. 16 A

Protection IP20

Protection class II

Working temperature 0°C to +40°C

Dimensions 110 x 80 x31 mm

Transmitter

Power supply

2 x1.5V alkaline AA batteries

(are included)

Communication type two-way

Hf power < 10 mW

Frequency 433.92 MHz

Hysteresis 0,4°C

Adjustable temp. range 11 to 29°C

(anti-freeze min. 3°C)

Temperature setting by 1°C (from 11°C)

Measurement accuracy ± 1°C

Protection IP20

Battery life 5 years

acc. to the battery type used

Working temperature 0°C to +40°C

If... Cause and solution...

the red LED is ﬂ ashing on the transmitter

3 times in 8 s

Low battery indication

Replace the batteries; see page 3

the red LED is ﬂ ashing on the transmitter

2 times in 8 s

Signal transmission failure between the

transmitter and receiver

Check the connection of the receiver; see

page 2; on the transmitter, push long (for

approx. 3 s) the button to test the

connection (the relay on the receiver must

switch several times).

the green LED is ﬂ ashing on the receiver

Empty memory; the transmitter code has not been

learned

Perform the code learning; see page 2

the green LED is permanently lit and the red

one is ﬂ ashing on the receiver

The receiver is in the error state (8 min OFF and 2

min ON)

Check the transmitter and test the connection

the green and red LED are ﬂ ashing alternately

on the receiver

The code-learning mode; the receiver is awaiting the

code

On the receiver, push long (for approx. 3 s)

the button

the both LED is lit on the receiver, but the

relay has not been switched

Output circuit failure

Contact the manufacturer immediately.

Produkt Specifikationer

Mærke:	Elektrobock
Kategori:	Termostat
Model:	BT012

Har du brug for hjælp?

Hvis du har brug for hjælp til Elektrobock BT012 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Elektrobock Manualer

Elektrobock PT741W-EI WIFI Manual

8 Juli 2025

Elektrobock BT730 Manual

31 August 2024

Elektrobock PT712-EI Manual

31 August 2024

Elektrobock PT 32 GST Manual

26 August 2024

Elektrobock BPT 32 Manual

26 August 2024

Elektrobock PT 14 Manual

26 August 2024

Elektrobock PT 713 EI Manual

26 August 2024

Elektrobock PT 713 Manual

26 August 2024

Elektrobock BPT 22 Manual

26 August 2024

Elektrobock BT52 Manual

20 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Vimar 30811.C Manual

31 Oktober 2025

Abus Comfion FUSH80100 Manual

29 Oktober 2025

Delta Dore Tybox 137 Manual

17 Oktober 2025

Delta Dore RF 6600 FP Manual

17 Oktober 2025

Emos P56A01 Manual

15 Oktober 2025

Fantini Cosmi C830RL Manual

14 Oktober 2025

UPM HTM311A Manual

12 Oktober 2025

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025