Emko EAOM-36 Manual

Emko Ikke kategoriseret EAOM-36

Læs gratis den danske manual til Emko EAOM-36 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Emko EAOM-36, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Features

Controls

FailMonitoring

EAOM-36ManualStartUnitusemicroprocessorbasedtechnologytoprovideintegratedmanualstartand

faultprotectioninawiderangeofengineapplications. Themoduleishousedin72x72DINsize.Themoduleis

usedtostartandstoptheengine,indicatingtheoperationalstatusandfaultconditions. Automaticallyshutting

downtheengineandindicatingtheenginefailurebyaflashingLED.Usercancontroltheengineviaatwoposition

keyswitchandpushbuttonsmountedonthefrontpanelorwithremoteinput.

Themodulehasthreeapplicationfeature;'Generator','Pump'or'FirePump'.(canbeselectedfrom

parameterP00).

Themodulecanconnectdirectlywithengine,thankstohighcurrentrelayoutputs.

Themodulehastwofeatureforfuel.Oneof“energizetorun”theother“energizetostop”.Usercanselectthe

featurefromprogramparameters.

The module protect the engine against fault conditions. If a fault condition occurred, the module indicate the fault

condition and shut-down the engine.

If the key switch is OFF position the module has zero power consumption to save energy. The module energizes

when the key switch position is getting ON position. If Satart button is pressed, the Conf. Out relay output (if selected

preheat output) will activate until the preheat delay is expired.

Press Start button for starting the engine. When engine is running, module will stop the cranking.

Press Stop button for stoping the engine. After pressing the stop button, the engine will keep running until cooling

time(P21) is expired.

Also the module has remote start facility. Please select suitable type of remote start for your application from

program parameters. If remote start input is active the module will start the engine. If remote start is passive the unit will

stop the engine after cooling time is expired.

The module will check the alarms after safety on timer is expired.

Under one of this fault conditions the module will stop the engine;

- Over speed (generator application),

- Under speed(generator application),

- High Temperature,

- Low Oil Pressure,

- Shutdown (if one of conf. input selected shutdown and activated).

To reset the fault, turn the key switch to the OFF position for a few seconds.

The Charge Failure is a warning alarm so the engine continue to work under this failure condition. Also this input

supplying charge alternator excitation current.

Shutdown the engine;

If the engine fuel type is “energize to stop”, press Stop button until the engine comes to rest. After that select OFF

position of the key switch.

If the engine fuel type is “energize to run”, select OFF position of the key switch.

On the Fire Pump application; If a fault condition occurred, the module will not stop the engine.

The engine will be stopped only when the stop button was pressed or the remote stop signal was detected.

Important note:

Manual and Remote Start with Key Switch, 72x72 DIN SizeUnit

DesignedForGenerator,Pump&FirePump Applications

Remotestart/stopcapabilitywithzeropowerconsumption

Enginestartandstop

Automaticshutdownonfaultcondition

Providesalarmandstatusinformation

Alarmandshutdowninputs

Provideschargealternatorexcitationcurrent

Lamptestfunction

Oilpressure

Enginetemperature

Overspeed&Underspeed(generatorapplication)

Chargingalternator

Conf.Input-1&2

Enginefuelorstopsolenoid

Startermotor

Preheat,simulatefuelsolenoid,externalalarm

horn,alarmorloadcontactorout

IntroductionBrochure.ENGEAOM-36R01V0612/17

START

Hz./

RPM

CHARGINGFAIL

~ ~

~~~~

HIGHTEMPERATURE

LOWOIL PRESSURE

FAILEDTOSTART

SPEED

FAILURE

EAOM-36

STOP

RPM

Produkt Specifikationer

Mærke:	Emko
Kategori:	Ikke kategoriseret
Model:	EAOM-36

Har du brug for hjælp?

Hvis du har brug for hjælp til Emko EAOM-36 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Emko Manualer

8 September 2025

8 September 2025

8 September 2025

8 September 2025

Emko TRANS MAINS Manual

8 September 2025

8 September 2025

8 September 2025

8 September 2025

8 September 2025

Emko Trans-MidiAUTO Manual

7 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MuxLab 500439 Manual

5 November 2025

GVM BL160-II Manual

5 November 2025

Uniprodo UNI_ROLL_03 2in1 Manual

5 November 2025

Rockville SS6 Manual

5 November 2025

Silk'n VacuPedi FTC04 Manual

5 November 2025

MEPROLIGHT MCO PRO Manual

5 November 2025

XPG Battlecruiser II Manual

5 November 2025

Hosa USQ-110 Manual

5 November 2025

JMAZ Centipede Quadro Manual

5 November 2025

Lake People Mic-Amp F311-D Manual

5 November 2025