Emko Eco PID Manual

Emko Temperaturregulator Eco PID

Læs gratis den danske manual til Emko Eco PID (2 sider) i kategorien Temperaturregulator. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Emko Eco PID, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Eco PID+, PID Temperature Control Un�t

- 4 d�g�t process (PV) and 4 d�g�t set (SV) d�splay

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptat�on of PID Coeff�c�ents to the system w�th Self-Tune and Auto-Tune

- Programmable Heat�ng or Cool�ng Funct�ons for Control Output

- Selectable Alarm Funct�ons for Alarm Output

- Ser�al RS485 Commun�cat�on (opt�onal)

Introduct�on Brochure. ENG EcoPID+ 01 V00 03/22

Easy Access D�agram For Program Parameters

Panel Mount�ng

Enter Password w�th �ncrement

or decrement buttons.

Approve password

w�th Enter button

Password Screen

Eco ser�es temperature controllers are des�gned for measur�ng and controll�ng a

temperature value. They can be used �n many appl�cat�ons w�th the�r TC and RTD

temperature measurement �nput, mult�-funct�on control outputs, selectable alarm

funct�ons.

They are ma�nly used �n glass, plast�c, petro-chem�stry, text�le, automot�ve and mach�ne

product�on �ndustr�es. Accurate and advanced controll�ng �s performed w�th selectable

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct�ons.

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermores�stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)

Measurement Range: Please refer to process �nput type select�on �n process menu

parameters sect�on.

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh�ch one �s greater) ±1 d�g�t max.

Thermores�stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh�ch one �s greater) ±1 d�g�t

max.

Cold Junct�on Compensat�on: Automat�cally ±0.1°C/1°C

L�ne Compensat�on: Max�mum 10 Ohm

Sensor Break Protect�on: Upscale

Sampl�ng Cycle: 0.1 second

Input F�lter: Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output: Relay (5A@250VV at res�st�ve load) or SSR Dr�ver Output

(Max�mum 10mA, Max. 12VZ )

Alarm Output: Relay (5A@250VV at res�st�ve load)

SUPPLY VOLTAGE (It must be determ�ned �n order)

230VV (±15%) 50/60Hz - 4VA

115VV (±15%) 50/60Hz - 4VA

100-240VV 50/60Hz - 4VA

24VV(±%15) 50/60Hz - 4VA

24VW (±%15) 50/60Hz - 4VA

10...30VZ - 4W

DISPLAY

Process D�splay: 16 mm Red 4 d�g�t LED D�splay

Set Value D�splay: 9 mm Orange 4 d�g�t LED D�splay

Led Ind�cators: PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operat�ng Temperature: 0...50ºC

Hum�d�ty : 0-90%RH (none condens�ng)

Mechan�cal Impacts: 1Joule (IK06)

Protect�on Class: NEMA 4X (IP65 at front, IP20 at rear)

We�ght: 150 gr.

D�mens�on: 48 x 48 mm, Depth: 86,5 mm

Panel CutOut: 46 x 46 mm

*1 - ON/OFF Hysteres�s parameter �s not act�ve unless parameter �s set as .

*2 - Soft Start parameters( , , ) �s not act�ve unless parameter �s set as .

*3 - Soft Start Control Output and Soft Start Control T�me parameters �s not act�ve �f parameter

�s set as .

*4 - PID control parameters are not act�ve unless parameter �s set as .

*5 - Alarm-2 parameters are not act�ve �f parameter �s set as .

*6 - Commun�cat�on parameters are not act�ve on dev�ces have no commun�cat�on module.

*7 - If �s d�fferent from 0 and user enters to program menu w�thout enter�ng the password

rot menu �s not shown.

Note: User can ex�t from any parameter screen w�thout sav�ng the values by press�ng button. If

no operat�on for 120 seconds, dev�ce automat�cally return to ma�n screen.

Easy Access D�agram For Sensor Break Output

Value From Ma�n Screen

Change the sensor break

output value w�th �ncrement

or decrement buttons.

Press Enter button to save

new sensor break output value

and ex�t.

Ma�n Screen Ma�n Screen

Note1: User can ex�t from parameter screen w�thout sav�ng the

values by press�ng button. If no operat�on for 120 seconds, dev�ce

automat�cally ex�ts from parameter screen.

Note2: Sensor break output value can be adjusted on programm�ng

sect�on too.

Tune Operat�on

Start�ng the Tune operat�on

1- Enter to the parameter �n menu and select

or ,then press button for sav�ng parameter and turn to ma�n

screen. Or eas�ly press button for 3 seconds* �n ma�n screen.

2- Observe that bl�nks �n set d�splay.

*Only Self Tune can be started by th�s way.

Cancel�ng Tune operat�on:

1- If sensor breaks;

2- If tune operat�on can not be completed �n 8 hours;

3- Wh�le heat�ng self tune �s runn�ng, �f process value becomes

greater than process set value;

4- Wh�le cool�ng self tune �s runn�ng, �f process value becomes less

than process set value;

5- Wh�le tune operat�on �s runn�ng, �f user changes the process set

value;

6- Wh�le tune operat�on �s runn�ng, �f user changes the

parameter �n menu;

Then tune operat�on �s canceled, dev�ce cont�nues to run w�th former

PID parameters w�thout chang�ng PID parameters.

PID TEMPERATURE CONTROL UNIT

PID+

Eco

D�mens�ons

48 mm / 1.89 �nch

6 mm / 0.24 �nch

80,52 mm / 3.17 �nch

Max�mum 9 mm / 0.35 �nch

1- Before mount�ng the dev�ce �n your panel,

make sure that the cutout �s of the r�ght s�ze.

2- Check front panel gasket pos�t�on.

3- Insert the dev�ce through the cutout. If the

mount�ng clamps are on the un�t, put out them

before �nsert�ng the un�t to the panel.

4- Insert the mount�ng clamps to the two of

des�gnated holes that located four s�des of

dev�ce.

5- Drag the mount�ng clamps �n d�rect�on 5

unt�l the dev�ce completely �mmob�le w�th�n the

panel.

6- In order to remove dev�ce push on the

mount�ng clamp as shown w�th arrow 6 and

pull back.

Access and Change Set Values

Press �ncrement or decrement

button to change process set value.

Press Enter button to save new

set value and return the ma�n screen.

Ma�n ScreenMa�n Screen

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000

Note-1: User can ex�t from set value sect�on w�thout sav�ng the values by press�ng button. If no

operat�on for 120 seconds, dev�ce automat�cally ex�ts from Set Value sect�on.

Note-2: Set value can be adjusted between Set Value Low and H�gh L�m�t ( - ).

Press Program button

to access password screen.

Electr�cal W�r�ngs

To reduce the effect of electr�cal no�se on dev�ce, low voltage l�ne (espec�ally sensor

�nput cable) w�r�ng must be separetely from h�gh current and voltage l�ne. If poss�ble,

use sh�elded cable and sh�eld must be connected to ground only one s�de.

Note-1: External Fuse �s recommended.

Note-2: Stranded cable cross sect�on: 1,5mm², Sol�d cable cross-sect�on: 2,5mm²

The str�pp�ng length �s 7mm to 9mm.

Note-3: Supply cables must comply w�th the requ�rements of IEC 60277 or IEC 60245.

It �s adv�sed to use a two-pole supply sw�tch, des�gnated for th�s dev�ce, w�th open/

closed pos�t�ons marked, �n order to cut the power. It must be placed on the supply

�nput of the dev�ce at a place where the user can eas�ly reach.

V External fuse must be on phase connect�on of the supply �nput.

Z External fuse must be on (+) l�ne connect�on of the supply �nput.

Make sure that the power supply voltage range �s su�table for the dev�ce.

Sw�tch on the power supply only after all the electr�cal connect�ons are �n place.

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

Ser�al Commun�cat�on

(RS485, Modbus RTU)

A+

B-

PID+

Eco

PT-100

Supply

Sw�tch

Supply

Voltage

1A T

Fuse

NOTE-1

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

5A@250V

PT-100

The Dev�ce

w�th Two Relays

The Dev�ce

w�th One Relay

Çalışma Ekranı

*2,3

*7*6

Produkt Specifikationer

Mærke:	Emko
Kategori:	Temperaturregulator
Model:	Eco PID

Har du brug for hjælp?

Hvis du har brug for hjælp til Emko Eco PID stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Temperaturregulator Emko Manualer

Emko ESM-9420 Manual

7 September 2025

Emko ESM-1520-N Manual

30 August 2024

Emko ECO PID+ Manual

30 August 2024

Emko Eco PID Manual

30 August 2024

Emko Eco Lite Manual

30 August 2024

Emko CHANNEL8A-N Manual

28 August 2024

Emko ESM-7720 Manual

28 August 2024

Emko ESM-3711-CN Manual

28 August 2024

Emko ESM-4410 Manual

27 August 2024

Emko ESM-4435 Manual

27 August 2024

Temperaturregulator Manualer

Nyeste Temperaturregulator Manualer

Inkbird ITC-308-WIFI Manual

30 September 2025

Inkbird ITC-306T-WIFI Manual

29 September 2025

Gossen Metrawatt R6000 Manual

26 September 2025

SRS PTC10 Manual

3 September 2025

Fluke 1504 Manual

2 September 2025

Festo SOEG-S-M18-S-L Manual

18 August 2025

Mueller GS 70.00 knx Manual

18 August 2025

Daikin KRCS01-8B Manual

11 August 2025

Daikin BRC4C61 Manual

11 August 2025

IFM LT8922 Manual

9 August 2025