Emos MD-410 Manual

Emos Multimeter MD-410

Læs gratis den danske manual til Emos MD-410 (88 sider) i kategorien Multimeter. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Emos MD-410, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/88

2202016000_31-M3691_00_01 105 × 148 mm

www.emos.eu

M3691 | MD-410

GB Digital Multimeter

CZ Digitální multimetr

SK Digitálny multimeter

PL Multimetr cyfrowy

HU Digitális multiméter

SI Digitalni multimeter

RS|HR|BA|ME Digitalni multimetar

DE Digitales Multimeter

UA Цифровий мультиметр

RO Multimetru digital

LT Skaitmeninis multimetras

LV Digitālais multimetrs

EE Digitaalne multimeeter

BG Цифров мултиметър

GB | Digital Multimeter

Carefully read through this instruction manual before you begin using the MD-410. It contains particularly

important passages concerning occupational safety principles when using the device. Such passages

are highlighted. Reading the manual will prevent potential injury by electric current or damage to the

device. The multimeter was designed in accordance with the IEC-61010 standard regarding electronic

measuring devices in the category (CAT III 300 V), 2nd degree of pollution. The CAT III category is used to

measure circuits powered by a xed output power supply, such as a relay, socket, switchboards, power

supplies and short branching circuits and lighting systems in large buildings.

Warning

Use the MD-410 multimeter only in the manner specied below. Other uses may cause damage to the

device or injury to your health.

Comply with the following instructions:

• Before measuring resistance, diodes or current, disconnect the circuits from the power supply and

discharge high-voltage capacitors. Use the corresponding function for the given measurement.

Before changing the range (of a function) disconnect the conductor from the circuit being measured.

• Make sure the device is not damaged before you begin using the multimeter. If you nd obvious

signs of damage on the body of the device, do not perform any measurements! Check that the

surface of the multimeter does not have scratches and that the side joints are not coming apart.

• Also check the insulation on the measuring probes. Damaged insulation may result in injury by

electric current. Do not use damaged measuring probes!

Produkt Specifikationer

Mærke:	Emos
Kategori:	Multimeter
Model:	MD-410

Har du brug for hjælp?

Hvis du har brug for hjælp til Emos MD-410 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Multimeter Emos Manualer

5 September 2024

10 August 2024

7 August 2024

6 August 2024

2 August 2024

1 August 2024

1 August 2024

12 Juli 2024

17 Februar 2024

30 December 2023

Multimeter Manualer

Nyeste Multimeter Manualer

Sauermann AMI 310 Manual

13 August 2025

Sauermann MP 210 Manual

13 August 2025

Bosch RM 3 Professional Manual

6 August 2025

Uni-T UT197PV Manual

5 August 2025

Fluke 17xx Manual

2 August 2025

Fluke 5550A Manual

2 August 2025

Kyoritsu KEW 2210R Manual

2 August 2025

Fluke T+ Manual

1 August 2025

Trotec BE60 Manual

1 August 2025

Kyoritsu K2413F Manual

1 August 2025