Erica Synths Plasma Drive Manual

Erica Synths Tastatur Plasma Drive

Læs gratis den danske manual til Erica Synths Plasma Drive (2 sider) i kategorien Tastatur. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Erica Synths Plasma Drive, eller vil du spørge andre brugere om produktet?

Side 1/2
PLA S MA DRIVE
HIG H VOLT AGE DIS TORTIO N U NIT
INPUT DRY/WET CV VOLT CV OUTPUT OCT TRIG SUB TRIG
OCT UP
OCT DOWN
EQ ON
EQ OFF
OCT
TRIGG
SUB
TRIGG
V
O
L
T
A
G
E
C
V
I
N
L
V
L
D
R
Y
/
W
E
T
V
O
L
T
A
G
E
T
R
E
B
L
E
B
A
S
S
A N D
THANK YOU FOR ORDERING
ERICA FUSION PLASMA DRIVE!
The Erica Synths Fusion series modules
are designed combining vacuum tubes
and semiconductors therefore they bring
warm, powerful sound and overdrive
possibilities of vacuum tubes into your
modular system.
Erica Fusion series consist of range of
modules used in sound shaping circuit
VCO, Mixer, real Ringmodulator using
audio transformers and germanium
diode ring, VCF, VCA, Analogue Delay/
Flanger, Palsma Drive and others.
Also Erica Fusion System is available.
Plasma Drive is result of Erica Synths
collaboration with a Latvian company
Gamechanger Audio, developers
of Plasma Pedal. It gives you a new
and previously unexplored method
of
achieving signal clipping - instead of
using LED circuits, transistors or vacuum
tubes to produce overdrive, the Plasma
Drive boosts audio signal to 3000V and
transforms it into a series of continuous
high-voltage discharges in a xenon-lled
tube. CV control over distortion level and
dry/wet mix, as well as octave up and 1
and 2 octaves down tracking oscillators
add even more harmonics to the original
signal. Tracking oscillators can be
adjusts nuances of sound. The Plasma
Drive module is powered via conventional
eurorack PSU ribbon cable and the power
consumption is around 150mA.
This three position
switch selects tracking
oscillators. In up
position +1oct is added
to the input sound,
in low position -1oct
is added to the input
sound, in the mid
position, both +1oct
and -1oct are added.
This provides extra
harmonics
and distortion
This is pre-distortion
circuit equalizer switch.
By default audio signal
after distortion circuit
is passed through the
equalizer. In the EQ
ON setting equalizer
is also added to the
input signal before the
distortion circuit
Adjust manually Voltage
CV level for desired
overdrive dynamics
This knob provides
smooth mix between
Dry and Wet signals,
Dry/Wet CV is added to
the knob position
Adjust input audio
signal level! Fusion
modules are sensitive
to input signal levels
and, adjusting it, can on
great deal change the
resulting sound
Adjust overdrive level
manually from light to
extreme in far CW setting.
The Voltage CV is added
to the knob
setting
Adjust equalizer high
frequency boost/cut
Adjust equalizer low
frequency boost/cut
This button engages
the tracking oscillators
depending on the Octave
switch setting. The tracking
oscillator is on, when the
button is lit
This button engages -2
and -3 octave tracking
oscillators.
These will be audible
only, if the Octave switch
is in the middle or low
settings (-1oct tracking
oscillator on)
These are octave trigger
inputs. The first incoming
trigger engages the
relevant tracking
oscillator, the second one
– disengages.
By sending trigger patter
into those inputs, you
can achieve interesting
rhythmic distortion
patterns
This is Voltage
CV input. The CV
is added to the
Voltage knob
setting
This is
the audio
output
of the
module
This is
audio
input
This is Dry/Wet
CV input. The CV
is added to the
Dry/Wet knob
setting
ERICA FUSION PLASMA DRIVE


Produkt Specifikationer

Mærke: Erica Synths
Kategori: Tastatur
Model: Plasma Drive

Har du brug for hjælp?

Hvis du har brug for hjælp til Erica Synths Plasma Drive stil et spørgsmål nedenfor, og andre brugere vil svare dig