EtherWAN OttoE 10H Manual

EtherWAN Ikke kategoriseret OttoE 10H

Læs gratis den danske manual til EtherWAN OttoE 10H (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7 anmeldelser. Har du et spørgsmål om EtherWAN OttoE 10H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

W70G- TG103HQ1 Page 1

Installation Guide

OttoE TG103(H) Series | Unmanaged PoE Ethernet Switch

Unpacking

Open the carton and unpack the items. Your package should include:

▪ One OttoE TG103(H) switch. Note that the (H) indicates hardened models.

If any items are missing or damaged, notify your EtherWAN representative. If

possible, save the carton and packing material in case you need to ship or store

the switch in the future.

Equipment Needed

▪ Appropriate cables for data ports. To prevent damage to the switch from

electrical surges, it is recommended to use STP (Shielded twisted pair) cabling

with a minimum rating of cat5e.

▪ Appropriate SFP modules for SFP ports

Select a Location

▪ Installation: Place the device on the DIN rail from above using the slot. Push

the front of the device toward the mounting surface until it audibly snaps into

place.

▪ Choose a dry area with an ambient temperature between -10 and 60ºC (-14

and 140ºF).

▪ Choose a dry area with an ambient temperature between -40°C to 75°C (-

40°F to 167°F) for H models.

▪ Keep away from heat sources, sunlight, warm air exhausts, hot-air vents, and

heaters.

▪ Be sure there is adequate airflow.

▪ For indoor use or in a sealed enclosure.

▪ Designed in accordance with pollution degree 2.

Connect to the Data Ports

Depending on the model, your switch can have the following ports:

TG103(H)-0800

8 Gigabit PoE ports

TG103(H)-0802

8 Gigabit PoE ports + 2 100/1G SFP ports

TG103(H)-0442

4 Gigabit PoE ports + 4 Gigabit TX ports + 2 100/1G SFP

ports

Connect Power

The switch has two power inputs. Only one power input is required to operate

the switch. Connect the supply voltage to start up the device via the terminal

block.

Power rating:

▪ PoE 30 Watts per port: 52–57 VDC, 5.47-4.99 A

▪ PoE 90 Watts per port: 54–57 VDC, 5.17-4.99 A

▪ Total PoE max.270W.

▪ The power input specification complies with the requirements of SELV (Safety

Extra Low Voltage), and the power supply should comply with UL 61010-1

and UL 61010-2-201.

Terminal Block

The switch provides two power inputs on a 52-57VDC terminal block.

State

Description

Power 1

52-57VDC

Power Ground

Power 2

52-57VDC

Power Ground

Earth Terminal

Relay Output Rating

0.5A @ 48VDC

Relay Output Alarm

The switch provides a relay output contact. The relay is used to indicate a user-

defined power redundancy failure. The current is 0.5A@48VDC at Normally Open

or Normally Closed.

Relay Contact

Normally Open

Normally Closed

No power

Open

Closed

Normal

Closed

Open

Abnormal

Open

Closed

LED Indicators

TG103(H)-0442 TG103(H)-0802 TG103(H)-0800

LED

Color

Status

L/A (Link/Active)

Green

On: Link active

Off: No link

Flashing: Data transmission

PWR 1 & 2

Green

On: Power on

Off: Power off

Alarm

Red

On: Error - power redundancy

failure

Off: No power error condition

PoE

Amber

On: Powered Device connected

Off: Powered Device disconnected

Power-Up Sequence

When the switch is powering up:

▪ All Link/ACT LEDs blink momentarily.

▪ The Power 1, 2 LEDs light up and stay lit.

▪ LEDs for every port connected to a device will flash, as the switch conducts a

brief Power On Self-Test (POST).

Quality of Service (QoS)

The QoS feature is automatically activated when the switch is running. Priority

mapping is handled according to the following tables:

CoS priority

(802.1p)

7, 6

5, 4

3, 2

1, 0

DSCP priority

59, 55

47, 46, 43

Other

Queues

WFQ

Highest

Priority

Secondary

Priority

EtherNet/IP: UDP 2222 (Queue 2)

Profinet Ether type: 0x8892 (Queue 2)

DIP Switch Settings

There is a 10-pin DIP switch for enabling the Watchdog (WDG) function.

When the DIP switch for a port is set to ON, the WDG function will be enabled

after the TG103(H) has been powered on for 10 minutes to give powered devices

time to boot. Every 30 seconds WDG will detect whether the packets from a

powered device are being received or not. If no packet is received after 30

seconds, connected ports with the DIP switch set to ON will be restarted (other

ports are not disturbed). If a packet is received in the 25th second, then the 30

seconds interval will be restarted.

If DIP switch 9 (EXT) is set to ON, the WDG function will be enabled after 5

minutes instead of 10 minutes after the switch powers on, to accommodate

faster booting powered devices.

Produkt Specifikationer

Mærke:	EtherWAN
Kategori:	Ikke kategoriseret
Model:	OttoE 10H

Har du brug for hjælp?

Hvis du har brug for hjælp til EtherWAN OttoE 10H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret EtherWAN Manualer

EtherWAN EX35000 Manual

15 November 2025

EtherWAN ED3238 Manual

13 November 2025

EtherWAN AiR PACE Manual

13 November 2025

EtherWAN EN301 Manual

7 November 2025

EtherWAN SPL90BT Manual

7 November 2025

EtherWAN EDGE 2 Manual

5 November 2025

EtherWAN OttoE 10H Manual

5 November 2025

EtherWAN EX42905 Manual

4 November 2025

EtherWAN ED3575 Manual

4 November 2025

EtherWAN AiR PACE CL Manual

4 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

KoolStar Starter 950 Manual

25 December 2025

VOX SETSF5702B Manual

25 December 2025

Yamazen SUC-202 Manual

25 December 2025

Vaxcel OW37081 Manual

25 December 2025

Vaxcel T0253 Manual

25 December 2025

Reelcraft L 4525 123 7A Manual

25 December 2025

Reelcraft L 5700 Manual

25 December 2025

Viewsonic ViewBoard IN8621C Manual

25 December 2025

Yamazen YTY-A410 Manual

25 December 2025

BlaknBlu Oscar DSF Manual

25 December 2025