EXSYS EX-60340 Manual


Læs gratis den danske manual til EXSYS EX-60340 (2 sider) i kategorien Audio/video konverter. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om EXSYS EX-60340, eller vil du spørge andre brugere om produktet?

Side 1/2
RJ45 Port
Pin Signal PoE Pin Signal PoE
1 BI_DA+ VCC+ 5 BI_DC- VCC+
2 BI_DA- VCC+ 6 BI_DB- VCC-
3 BI_DB+ VCC- 7 BI_DD+ VCC-
4 BI_DC+ VCC+ 8 BI_DD- VCC-
87654321
6 5
rung zwischen Kupfer- und Lichtwellenleiter-Umgebungen. Er ist kompatibel zu
10/100/1000Base-T mit 60W PoE+ und dual mode 100/1000Base-X SFP (auto detection). Der
Ethernet-Port unterstützt sowohl den Halbduplex- als auch den Vollduplex-Modus. Je nach
Bedarf können verschiedene Arten von optional erltlichen SFP-Modulen verwendet werden.
Dank dem robusten Metallgehäuse und dem erweiterten Betriebstemperaturbereich von -40°C
bis 80°C ist er für eine Vielzahl von Anwendungen auch in rauen Umgebungen geeignet. Die
Stromversorgung erfolgt über den Terminal Block (12~48VDC). Der EX-60340 unterstützt Auto-
MDI/MDI-X und Auto-Negotation. Im Lieferumfang ist ein DIN-Rail Kit (vormontiert) und ein
Wandmontagebügel enthalten.
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Kompatibilität: Gigabit Ethernet 10/100/1000Base-T, 100/1000Base-X
PoE: IEEE 802.3af/at (PoE+)
PoE (PSE): Typ 1 = 15.4W / Typ 2 = 34.2W / 4PPoE = 60W
Betriebssysteme: Alle Betriebssysteme
Anschlüsse: 1x RJ45-Buchse, 1x SFP-Slot, 1x Terminal Block 12~48VDC
Lieferumfang: EX-60340, DIN-Rail Kit, Wandmontagehalterung, Anleitung
HARDWARE INSTALLATION
CONNECTORS & LED'S
12-48V T-Block für optional
erhältliches Netzteil
12V to 48V T-Block:
ATTENTION!
Please pay attention to the correct polarity!
Never connect the power supply to the terminal block
while it is switched on!
Redundant power supply possible to reduce operational failure.
Both power supplies must use the same voltage!
V- V+ V- V+
RJ45 Port:
Please read the following installation instructions.
1. Install the EX-60340 on a mounting rail using the DIN-Rail kit or on the wall using the wall
mounting bracket.
2. Slide the optionally available SFP transceiver into the SFP slot.
3. Connect your network device (PoE IP Camera etc.) to the switch using a network cable.
4. Connect the fiber optic cable used to connect to the media converter or switch to the SFP
transceiver you are using.
CAUTION! Do not look directly into the laser beam of the fiber optic connector!
5. Connect the power connector of the optionally available power supply to the terminal block
and switch on the power supply.
6. After the power is turned on, the PWR indicator lights up. If the indicator does not light up,
check that it is connected to the power supply correctly.
7. When all cables are connected correctly, the indicators light up according to the port status
of the LEDs (page 5).
The DIN-Rail Kit is pre-assembled with
two screws on the rear side
To install the wall mount, the DIN-
Rail kit must be replaced by the
mounting bracket
Betriebs-LED
1x SFP Slot
100/1000
SFP slot:
ATTENTION!
SFP Transceivers are a Class 1 Laser/LED product. To avoid
causing serious damage to your eyes, do not stare
directly into the laser beam.
LINK / Activity LED
PoE LED
Status LEDs:
LED Name Color LED Function
LINK (ACT) Yellow
Steady on: Linked
Blinking: Data Transmission
FX
Green
Steady on: Fiber linked
Blinking: Data Transmission
PoE Green
Steady on: PoE is activated
Blinking: Power Device (PD) detected
Off: No (PD) device connected
FX LED
1x RJ45
Gigabit PoE
FX-LED
Status LEDs
E 6034
Anleitun
Vers. 1.1 / 20.12.24
Switzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
Italy:
EXSYS Italia Srl
Via Belvedere, 45/B
I-22100 Como
www.exsys.it
Procedure for STP Cable Grounding
When using shielded cables to connect two Ethernet devices, a ground loop may occur if the
shielding on the cables generates an additional grounding connection path. This can cause
ground current to flow through to the Ethernet ports and damage the devices. If it is necessary
metallic connector on the other end. Alternatively, a patch panel can be used in between the
two devices to prevent ground loops from occurring.
Switch off the power supply before disconnecting modules or wires.
The propper power supply voltage is indicated on the product label. Check the voltage of your
power source to ensure you are using the correct voltage. DO NOT use a voltage higher than
what is specified on the product.
SFP Transceivers are a Class 1 Laser/LED product.
To avoid causing serious damage to your eyes, do not stare directly into the
laser beam.
NOTICE & CLEANING
To clean the device, please use only a dry, non-fibrous cloth and remove the dirt with light
pressure. In the area of the connections, please make sure that no fibers of the cloth are left in
the socket.
Attention! Never use a moist or wet cloth for cleaning!
ACHTUNG!
Bei geerdetem Minuspol der Stromversorgung
unbedingt den Technischen Hinweis auf Seite 3
beachten.


Produkt Specifikationer

Mærke: EXSYS
Kategori: Audio/video konverter
Model: EX-60340

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-60340 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Audio/video konverter EXSYS Manualer

Audio/video konverter Manualer

Nyeste Audio/video konverter Manualer

BirdDog

BirdDog FLEX 4K BP Manual

5 December 2025
BirdDog

BirdDog 4K SDI Si2 Manual

4 December 2025
BirdDog

BirdDog PLAY Manual

3 December 2025
BirdDog

BirdDog FLEX 4K OUT Manual

3 December 2025
BirdDog

BirdDog 4K Quad Manual

2 December 2025
BirdDog

BirdDog OG4 Manual

2 December 2025
BirdDog

BirdDog 4K HDMI Si2 Manual

2 December 2025
MuxLab

MuxLab 500427 Manual

1 December 2025
MuxLab

MuxLab 500425 Manual

1 December 2025
MuxLab

MuxLab 500412-V2 Manual

1 December 2025