Extron TLP Pro 1725MG Manual

Extron overvåge TLP Pro 1725MG

Læs gratis den danske manual til Extron TLP Pro 1725MG (6 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Extron TLP Pro 1725MG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

www.extron.com

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Overview

The Extron® TLP Pro 1225MG, TLP Pro 1525MG, and TLP Pro 1725MG are wall-mounted touchpanels with capacitive, edge-to-edge

glass touchscreens. The TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525MG has a 15.6 inch

screen with a 1366x768 resolution. The TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution. All three touchpanels

are ideal for any AV applications requiring large touchpanels with exible mounting options and fully customizable interfaces. This

guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the

TLPPro 1225, 1525, and 1725 Series User Guide at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

GUI Designer — Used to design layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces.

Global Configurator® Plus and Professional — Used to set up and congure the control processor and touchpanel.

Global Scripter® — Used to rovide an integrated development environment for Extron control systems programming.

Global Scripter provides an Extron-exclusive Python™ library (ControlScript®) and modules to get you started.

Toolbelt — Used for device discovery, device information, rmware updates, and conguration of network settings, system

utilities, and user management for TouchLink Pro devices.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you also require:

IP address Subnet mask Gateway

Username — This can be either or .

Passwords — The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords can be changed during conguration. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is (for

either or ).

Make a note of the touchpanel MAC address from the label on the back of the device.

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels until you have read the Attention in the “Power Supply” section of the

TLPPro 1225, 1525, and 1725 Series User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «sources d’alimentation» du TLPPro

1225, 1525, and 1725 Series User Guide.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see on page 2). Mounting

Connect cables to the touchpanels (see on page 4).Rear Panel Features

Connect the touchpanel to a Power over Ethernet (PoE) injector. The TLP Pro 1725MG ships with the PI 140 power injector.

A power injector must be purchased separately for the 12-inch and 15-inch models.

Connect an Extron IP Link® Pro control processor to the same Ethernet subnetwork as the touchpanel.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and touchpanel .to the same Ethernet subnetwork

Use the (see page 6) or Toolbelt (see Setup Menu Toolbelt Help File) to set the DHCP status and, if necessary, the IP

address, subnet mask, gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

Create a graphical user interface with GUI Designer (see for step-by-step instructions).GUI Designer Help File

Associate functions with the graphical user interface features by conguring (see the ) or Global Conﬁgurator Help File

programming (see the ) the system.Global Scripter Help File

TLP Pro 1225MG, 1525MG, and 1725MG • Setup Guide

Mounting

ATTENTION:

• Do not install the TLP Pro 1225MG, TLP Pro 1525MG, or TLP Pro 1725MG in a re resistant rated wall or partition

assembly.

• Ne pas installer le TLP Pro 1225MG, le TLP Pro 1525MG, ou le TLP Pro 1725MG dans un mur résistant au feu ou une

cloison.

• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and

national building codes and electrical codes.

• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du

bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

Wall Mounting

The touchpanels can be wall mounted using the provided hardware. Where local codes require a rear metal enclosure, either model

can be mounted using the Extron BB 700M (not provided). Figure 1 shows the TLP Pro 1525MG. Mount the TLP Pro 1225MG or

TLP Pro 1725MG in the same way.

With a wall box

Some local building codes require the touchpanel to be mounted in a wall box such as the Extron BB 700M. This installation

procedure is described below.

1. Cut a hole in the drywall, 9.6 inches (243 mm) wide

x 6.6 inches (166 mm) high, and install the

Install the BB 700M (optional).

TLP Pro 1525MG

Back View

Hold the touchpanel at a slight angle

Mount the touchpanel over the two

hooks on the mounting plate.

Add the mounting plate. Align with

the wall box and mark holes for screws.

Secure the mounting plate

to the wall with screws (4).

Place the provided mounting sc ws (2)re

with washers in the mounting sc w slotre

in the touchpanel.

Secu the touchpanel by tightening there

mounting sc ws against the base of the re

mounting plate.

BB 700M (see gure 1, 1), as described

in the (see BB 700M Installation Guide

www.extron.com).

2. Place the metal mounting plate

against the wall, mark the four

mounting holes, and drill four pilot

holes (2) in those locations.

3. Secure the mounting plate with four

#10 screws (3).

4. Run and connect cables to the back

of the touchpanel (4, and see Rear

Panel Features on page 4).

5. Insert the two provided Phillips pan

head #6-32 x ¾ inch length screws

with washers in the mounting screw

slot (5, see gure 1, Back View

inset). Leave a gap for the ange at the

bottom of the mounting plate to t into.

6. Hold the touchpanel at a slight angle

and lower the notches at the top of

the back panel over the hooks of the

mounting plate (6).

7. Swing the bottom of the touchpanel

inwards so that it lies at against the

mounting plate with the ange at the bottom

of the mounting plate sitting in a groove in the

bottom of the touchpanel.

8. Secure the touchpanel to the mounting plate with the

mounting screws (7).

Without a wall box

If the wall box is not required by local building codes, you can

mount the touchpanel directly into drywall.

1. Download the cut-out template for your touchpanel from Figure 1. TLP Pro 1525MG Mounting

www.extron.com. Print it at 100% (no scaling).

2. Use the template to mark the wall, cut the hole, and drill the four pilot holes. The size of the cut-out hole is 9.25 inches (235 mm)

wide x 6.25 inches (159 mm) high.

3. Secure the mounting plate and complete the installation, as described in steps 3 through 8 above.

Produkt Specifikationer

Mærke:	Extron
Kategori:	overvåge
Model:	TLP Pro 1725MG

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron TLP Pro 1725MG stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

overvåge Extron Manualer

Extron TLS 1025M Manual

2 April 2025

Extron TLP Pro 525C Manual

18 September 2024

Extron TLP Pro 525T Manual

6 September 2024

Extron TLP Pro 725M Manual

6 September 2024

Extron TLP Pro 1525TG Manual

6 September 2024

Extron TLP Pro 1725MG Manual

6 September 2024

Extron TLP Pro 1025M Manual

6 September 2024

Extron TLP Pro 1025T Manual

5 September 2024

Extron TLP Pro 725T Manual

5 September 2024

overvåge Manualer

Nyeste overvåge Manualer

BenQ DesignVue PD2730S Manual

8 April 2025

Asus VA279QGS Manual

8 April 2025

Acer EV227Q Manual

8 April 2025

BenQ PD3226G Manual

7 April 2025

Philips 221V8LB Manual

4 April 2025

PureTools PT-SCREEN-100 Manual

1 April 2025

Viewsonic VG2752-2K Manual

30 Marts 2025

Satco S13165 Manual

30 Marts 2025

Satco S16434 Manual

30 Marts 2025

Satco S23165 Manual

30 Marts 2025