Extron TLP Pro 525C Manual
Læs gratis den danske manual til Extron TLP Pro 525C (10 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Extron TLP Pro 525C, eller vil du spørge andre brugere om produktet?
Side 1/10
1
TLP Pro 525C Series • Setup Guide
Overview
The Extron TLP Pro 525C is a 5-inch Cable Cubby touchpanel. It has a ip-up, 800x480 (WVGA), LCD touchscreen with
24-bit color depth. The TLP Pro 525C NC is a streamlined model, with a set of features that adhere to government and military
security protocols.
These touchpanels are suitable for any AV application requiring a Cable Cubby touchpanel with a customizable interface.
This guide provides instructions for experienced installers to mount and install these touchpanels. For more complete instructions,
see the at TLPPro 525C and 725C Series User Guide www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — For designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces.
Global Configurator® Professional and Global Configurator Plus — For setting up and conguring the control
processor and touchpanel.
Toolbelt — Provides device discovery, device information, rmware updates, and conguration of network settings,
system utilities, and user management for TouchLink Pro devices.
Global Scripter® — Provides an integrated development environment for Extron control systems programming.
NOTE: All four software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status — (on or off). If DHCP is off, you must also obtain:
IP address Subnet mask Gateway
User name — This can be either or .
Password — The factory congured passwords for all accounts on this device have been set to the device serial
number. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password will be the default password conguration. The default
password is (for either or ).
Make a note of the touchpanel MAC address.
Make sure you are familiar with all the included parts and have all the necessary Tools Required for Installation (see
page 4) for installing the cable cubby.
Included Parts
Check that all the following parts are included:
3/8” Hole Plug (4)1/4” Hole Plug (1)
#6-32 Sc w (4)#6 Star Washer (4) re
TLP Pro 525C or
TLP Pro 525C NC (1)
2-space
MAAP Frame (1)
TLP Pro 525C
Connectivity
Bracket (1)
Short Clevis Pin (1)
Cotter Pin (1)
HDMI Lockit (1)
Tie wrap (1)
5-cable Pass-through
Plate (1)
Figure 1. TLP Pro 525C Included Parts
NOTE: Active or passive MAAPs must be purchased separately (see www.extron.com).
2
TLP Pro 525C Series • Setup Guide (Continued)
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels until you have read the attention notication in the “Base Features” section of the
TLPPro 525C and 725C Series User Guide.
• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde de la section «Base Features » du TLPPro 525C and
725C Series User Guide.
Cut a hole in the table (see Step 1 — Verify Cut-out Dimensions Step 2 — Cut the Surface on page 4 and on
page 5).
Run cables to the cable cubby (see on page 5).Step 3 — Run all Cables
Install modules into the Cable Cubby enclosure. Multiple optional modules can be installed in the TLP Pro 525C Cable Cubby
in a variety of congurations. Decide which modules and which conguration best serve your needs. Options include:
• Cable Retractors (see on page 5).Step 4 — Install Cable Retractors (Optional)
• Pass-through Cable Modules (see Step 5 — Assemble the Pass-through Cable Module (Optional) on page 6).
• AAP Modules (see on page 6).Step 6 — Assemble the MAAP Module (Optional)
• Power Modules (see on page 7).Step 7 — Install Modules
Use the setup menu for initial conguration of the touchpanel (see on page 10).Setup Menu
Mount the units (see on page 9).Step 8 — Mounting the Enclosure
Connect the touchpanel to a Power over Ethernet (PoE) injector (see on page 10).figure 13
Connect the power injector to the LAN and power it on (see ).figure 13
Set up the Touchpanels for Network Communication
Connect the PC that you are using for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.
Use the (see page 10) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, Setup Menu
gateway, and related settings for the touchpanel.
Configure the Touchpanels
The , the , and the GUI Designer Help File Global Configurator Help File Toolbelt Help File provide step-by-step instructions and
detailed information. The includes an introduction to the software and sections on how to start a Global Configurator Help File
project and conguration.
Global Scripter provides an Extron-exclusive Python library (ControlScript®) and Global Scripter modules to get you started.
Produkt Specifikationer
| Mærke: | Extron |
| Kategori: | overvåge |
| Model: | TLP Pro 525C |
Har du brug for hjælp?
Hvis du har brug for hjælp til Extron TLP Pro 525C stil et spørgsmål nedenfor, og andre brugere vil svare dig
overvåge Extron Manualer
18 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
5 September 2024
5 September 2024
overvåge Manualer
- Palmer
- EMachines
- AMX
- Philips
- BenQ
- HKC
- IOIO
- NEC
- Peerless-AV
- Toshiba
- Samson
- NewStar
- Kubo
- Fujitsu
- PeakTech
Nyeste overvåge Manualer
4 April 2025
5 Marts 2025
5 Marts 2025
27 Februar 2025
21 Februar 2025
18 Februar 2025
11 Februar 2025
11 Februar 2025
11 Februar 2025
11 Februar 2025