Fluke 700HTP-2 Manual

Fluke Pumpe 700HTP-2

Læs gratis den danske manual til Fluke 700HTP-2 (2 sider) i kategorien Pumpe. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Fluke 700HTP-2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
PN 4096896
September 2011
2011 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
How to Prime Pump the Test
Before you connect the to the Unit Under T), the Pump Test (UU
Pump must be lled with uid and primed for use. Follow the
directions below to prepare the for use. Pump
1. Fill the with uid: Pump
a. Remove the Reservoir Filler Cap (item .)
b. Fill the Hydraulic Fluid Reservoir approximately -thirds full two
(66 with distilled water, mineral oil, or hydraulic oil. cc)
Note
If water is used in the , use only DISTILLED water Pump
and drain the water out of the after use. Pump
c. Install the Reservoir Filler Cap (item .) Tighten by hand.
2. the : Prime Pump
a. Adjust the Vernier Fine Adjustment Knob (item ) to the
approximate dle-range.mid
b. Turn the Pressure Bleed Knob (item ) clockwise until it
stops in the full closed position.
c. Squeeze the handles together to pump uid. uid until Pump
uid shows at the . Pump Port
d. Attach the uid hose to the . Pump
e. Squeeze the handles together until uid shows at the end of
the hose.
f. Attach the uid hose to the Unit Under (UUT) and Test
squeeze the handles until pressure increases. Pump
g. Bleed the trapped air from the Pump. Pressurize the Pump to
1,000 psi then slowly turn the Pressure Bleed Knob (item )
counter-clockwise to release pressure.
Notes
• As the pressure it will be hard to squeeze the rises
handles together. Use the Handle Limiter (item ) to
limit the travel of the handles which will make them
easier to squeeze together. toggle the Handle To
Limiter on or o, squeeze the handles together and
push the Handle Limiter (item
) in or out.
• The rate at which the pressure increases is directly
related to the test conguration (hose length and
volume of UUT.)
Replacement Parts
Rebuild Kit, Fluke PN 4097836
Hydraulic Fluid Reservoir Rebuild , Fluke PN 2844341 Kit
Handle Assembly Rebuild , Fluke PN 2844352 Kit
LIMITED WARRANTY AND OF LIABILITYLIMITATION
This Fluke product will be from defects in material and workmanship for free
one year from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage from accident, neglect, misuse, alteration,
contamination, or conditions of operation or . Resellers are abnormal handling
not authorized any obtain to extend other warranty on Fluke’s behalf. To
service during the warranty period, contact your nearest Fluke authorized
service r cente to obtain return authorization information, then send the product
to that with a description of the problem.Service Center
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE SPECIAL, INDIRECT, IS NOT LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or of an implied warranty or of incidental or limitation
consequential damag not apply to you.es, this limitation of liability may
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
Fluke 700HTP- -2
Hydraulic Test Pump
Instruction Sheet
Introduction
The Fluke 700HTP-2 Hydraulic (the or ProductTest Pump Pump ) is a
portable source of high pressure.
Safety
W Warning
To prevent personal injury se the Product only as , u
specified, or the protection supplied by the Product can be
compromised.
Pump Sp ecifications
• Maximum pressure: 10,000 psi (690 bar)
• raulic media: distilled water, mineral based hydraulic oil, up Hyd or
to hydraulic oil 100 (30 W).
• Wetted materials: 303 stainless steel, aluminum, polyurethane,
PTFE, nitrile, and nylon.
• Weight: 1.29 lb (0.58 kg)
• Dimensions: length 9.5 41 mm), width 6.1 in (155 mm), depth in (2
2.6 in (66 mm)
Box Contents
• Model 700HTP-2 Hydraulic with a 1/4- NPT tee Test Pump inch
installed.
• 1/4- NPT male to 1/4- female adapters. Two inch inch BSP
• One 1/4- NPT male to 1/4- NPT male tting. inch inch
• One 1/4- NPT male to 1/8- NPT male tting. inch inch
• Instruction Sheet
How to Contact Fluke
To contact Fluke, call one of the following telephone numbers:
• Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
• Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
• Canada: 1-800-36-FLUKE
(1-800-363-5853)
• Europe: +31 402-675-200
• Japan: +81-3-6714-3114
• Singapore: +65-738-5655
• Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit . http://register.uke.com
To view, print, or download the latest manual supplement, visit
http://us.uke.com/usen/support/manuals.

Produkt Specifikationer

Mærke: Fluke
Kategori: Pumpe
Model: 700HTP-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke 700HTP-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Pumpe Fluke Manualer

Fluke

Fluke 700HTP-2 Manual

14 December 2023
Fluke

Fluke 700LTP-1 Manual

16 December 2022
Fluke

Fluke 730LTP600K Manual

8 November 2022

Pumpe Manualer

Nyeste Pumpe Manualer

Dedra

Dedra N1540 Manual

31 Oktober 2025
Westinghouse

Westinghouse WH50SS Manual

15 Oktober 2025
Westinghouse

Westinghouse WH50BBU Manual

14 Oktober 2025
Coleman

Coleman QuickPump Manual

13 Oktober 2025
Pontec

Pontec PondoMax Eco 5000 Manual

12 Oktober 2025
Pontec

Pontec PondoCompact 1200 Manual

12 Oktober 2025
Pontec

Pontec PondoAir Set 3600 Manual

12 Oktober 2025
Pontec

Pontec PondoCompact 500i Manual

12 Oktober 2025
Pontec

Pontec PondoGarden 3200 Manual

12 Oktober 2025
Pontec

Pontec PondoCompact 800 Manual

11 Oktober 2025