Fusion SG-FT88SPWC Manual

Fusion Højttaler SG-FT88SPWC

Læs gratis den danske manual til Fusion SG-FT88SPWC (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Fusion SG-FT88SPWC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Waketower Can Speakers Installation Instructions............................................................................2

Instructions d'installation Waketower Can......................................................................................... 4

Waketower Can Istruzioni di installazione......................................................................................... 6

Waketower Can Lautsprecher – Installationsanweisungen............................................................... 8

Instrucciones de instalación de los altavoces Waketower Can....................................................... 10

Waketower Can Waketower Can..................................................................................................... 12

Waketower Can luidsprekers installatie-instructies..........................................................................14

Garmin®, the Garmin logo, FUSION®, and the Fusion logo, are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express

permission of Garmin.

October 2018

190-02482-90_0A

Waketower Can Speakers Installation

Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vehicle or vessel, or poor product

performance.

This device must be installed according to these instructions.

Disconnect the vehicle's or vessel's power supply before

beginning to install this product.

CAUTION

Continuous exposure to sound pressure levels over 100 dBA

may cause permanent hearing loss. The volume is typically too

loud if you cannot hear people speaking around you. Limit the

amount of time you listen at high volume. If you experience

ringing in your ears or muffled speech, stop listening and have

your hearing checked.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

It is strongly recommended that you have your audio system

installed by a professional installer to ensure optimum

performance.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation, go

to for product support.www.fusionentertainment.com

What's In the Box

• Two Waketower can speakers

Materials and Tools Needed

• 18 AWG (0.82 mm2) wire (speakers)

• 20 AWG (0.5 mm2) wire (LEDs)

• 3 A in-line fuses (LEDs)

• Speaker mounting bracket (sold separately)

• Drill and 12 mm (1/2 in.) drill bit

• Wire strippers

• Solder and heat-shrink tubing for wire connections

NOTE: For customized installations, additional tools and

materials may be needed.

Mounting the Speakers

You must purchase mounting brackets for the FUSION

Waketower Can speakers separately. Each type of mounting

bracket contains specific installation instructions.

1If necessary, mark the locations on the waketower or the

deck where you plan to mount the speakers.

2If necessary, drill a 12 mm (1/2 in.) cable pass-through hole in

the waketower or deck.

3Route the speaker and LED power wires (not included) to the

mounting locations.

4Using the installation instructions provided with the mounting

bracket, connect the bracket to the speakers and to the

waketower or the deck.

5Connect the speaker wires ( ).Speaker Wiring, page 2

6If necessary, connect the LED power wires (Speaker LED

Wiring, page 2).

7If speakers were installed at an angle, rotate the front of the

speaker and the endcap so the FUSION logo appears level

( ).Adjusting the Angle of the FUSION Logos, page 2

Speaker Wiring

When connecting the speakers to your stereo, observe these

considerations.

• Speaker wire is not included with the speakers. You should

use 18 AWG (0.82 mm2) speaker wire to connect the

speakers to the stereo.

• You should make all wiring connections using solder and

heat-shrink tubing (not included).

• You can use this table to identify the polarity of the leads on

the speaker.

White Positive (+)

White with a black stripe Negative (-)

Speaker LED Wiring

You can control the color of the LEDs through the polarity of the

LED wires.

• Wire is not included with the speakers. You should use

20 AWG (0.5 mm2) or thicker wire to connect the speaker

LEDs to power.

• You should connect the positive (+) power wire to a 12 Vdc

power source through an isolator switch or circuit breaker to

turn the speaker LEDs on and off.

NOTE: You can use the same isolator or circuit breaker

controlling the power supply to your stereo, which allows you

to turn the speaker LEDs and the stereo on and off at the

same time.

• You should make all wiring connections using solder and

heat-shrink tubing (not included).

• You can use this table to connect the LED wires from the

speaker to power according to the preferred LED color.

Blue LED Black to negative (-)

Red to positive (+)

White LED Black to positive (+)

Red to negative (-)

Adjusting the Angle of the FUSION Logos

You should secure the speaker to the waketower or the deck

before adjusting the angle of the FUSION logos.

If you installed the speaker at an angle, you can rotate the front

and the endcap so the FUSION logos appear level.

1Remove the six #2 Phillips screws holding the front of the

speaker to the can.

2Rotate the front of the speaker until the FUSION logo

appears level.

You can rotate the front of the speaker in 30-degree

increments.

3Secure the front of the speaker to the can using the screws

you removed in step 1.

4Rotate the endcap on the back of the can by hand until the

FUSION logo appears level.

5Repeat this procedure for other speakers on the boat, as

needed.

Speaker Information

True-Marine™ Products

True-Marine products are subjected to rigorous environmental

testing under harsh marine conditions to surpass industry

guidelines for marine products.

Any product that bears the True-Marine stamp of assurance has

been designed for simplicity of use and combines advanced

marine technologies to deliver an industry leading entertainment

2 Installation Instructions

Produkt Specifikationer

Mærke:	Fusion
Kategori:	Højttaler
Model:	SG-FT88SPWC

Har du brug for hjælp?

Hvis du har brug for hjælp til Fusion SG-FT88SPWC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Fusion Manualer

Fusion EL-F653W Manual

9 Januar 2025

Fusion SG-CL65SP Manual

20 August 2024

Fusion XS-F40CWB Manual

19 August 2024

Fusion MS-EL602 Manual

18 August 2024

Fusion XS-F65SPGW Manual

17 August 2024

Fusion XS-FL65SPGW Manual

16 August 2024

Fusion SG-F65W Manual

16 August 2024

Fusion FM-F65RW Manual

16 August 2024

Fusion SG-F772W Manual

16 August 2024

Fusion SG-FL882SPC Manual

16 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Greadio R-919 Manual

14 Juni 2025

J.W. SPEAKER 8700 Evolution J2 Manual

14 Juni 2025

SpringFlora HM11 Manual

14 Juni 2025

Fiodio F-130 Manual

14 Juni 2025

HEYSONG Bubble Manual

14 Juni 2025

ANCOBER ACB-001 Manual

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025