Futaba SBD-1 Manual

Futaba Radiostyret legetøj SBD-1

Læs gratis den danske manual til Futaba SBD-1 (2 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Futaba SBD-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

󾙏CAUTION

󾙍 Do not connect any device (gyro, battery,

etc.) other than servos to the servo

connector of the SBD-1. There is the danger of

erroneous operation or damage.

󾙍 Do not connect an S.BUS conne cto r

of the SBD- 1 to other than an S.BUS

servo connection port. There is the danger of

erroneous operation or damage.

󾙏WARNNG

󾙋 Always use in the state in which the

SBD-1 is ﬁrmly attached to the fuselage

of the airplane or helicopter. There is the danger

of loss of control and crashing if the connector is

disconncted by vibration and shock.

Futaba Co rp. will not be resp onsible for

damage caused by combination with other

than Futaba Genuine parts.

S.BUS Decoder

INSTRUCTION MANUAL

Before using your new SBD-1, please read this manual

thoroughly and use the system properly and safely.

After reading this manual, store it in a safe place.

•Channel setting by SBC-1

1 Connect the S.BUS connector of the SBD-1

to the S.BUS servo connection port of the

SBC-1.

2 C o nne c t t he bat t e r y t o t he bat t e r y

connection port of the SBC-1.

* Status display LED blinks slowly. (About 1 sec/time)

3 Quickly press and release the SBC-1 setting

switch and select the servo connection port

at which the channel is to be set.

* Each time the switch is pressed, the set servo

connection port and the number of times the LED

blinks change.

SBC-1 SBD-1 servo con-

nector selection

Se tt in g s wit ch

operation LED display

W h e n p o w e r

turned on

1 sh o r t b l i n k

each second

Connector (SX1)

selected.

Switch pressed

a nd r e l e a s e d

quickly

2 s h o r t b li nk s

each second

Connector (SX2)

selected.

Switch pressed

a nd r e l e a s e d

quickly

3 s h o r t b li nk s

each second

Connector (SX3)

selected.

* (Channel conrmation)

When the operation position of the channel selector

switch and the channel set at the connector during

the servo connector selection coincide, the SBD-1

LED changes to a steady light.

4 Set the SBC-1 channel selector switch to

the channel you want to set.

5 Hold down the setting switch (about 1

second).

manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent

errors or omissions. Please contact our service center if you feel that any corrections or clariﬁcations should be made.

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

1M23N23401 ©FUTABA CORPORATION 2010, 2 (1)

Meaning of Special Markings

Pay special attention to safety where indicated by the following marks:

󾙏DANGER Procedures which may lead to dangerous conditions and

cause death/serious injury if not carried out properly.

󾙏WARNING

Procedures which may lead to a dangerous condition or

cause death or serious injury to the user if not carried out

properly, or procedures where the probability of superﬁcial

injury or physical damage is high.

󾙏CAUTION

Procedures where the possibility of serious injury to the user

is small, but there is a danger of injury, or physical damage,

if not carried out properly.

󾙍= Prohibited 󾙋= Mandatory

Usage Precautions

Name of Each Part and Accessories

Channel Setting

Usage Method

•Connection

1 Connect the S.BUS connector of the SBD-1

to the receiver S.BUS connection port or

S.BUS hub.

2 Connect a conventional servo or an S.BUS

servo to the servo connector of the SBD-1.

* When an servo was connected, that servo S.BUS

will operate as a conventional servo. However,

it operates on th e channel s et at th e s er vo

connector of the instead of the channel set SBD-1

at the servo itself.

Thank you for purchasing an SB D-1, S.BUS* 1

decoder. The SBD-1 is a converter for using

conventional servos (other than S.BUS servo*2) with

the S.BUS system.

There are ve types of SBD-1 available as follows.

Type Total Length

S.BUS Decoder

SBD-1

200 200mm (8in.)

400 400mm (16in.)

600 600mm (24in.)

1100 1,100mm (43in.)

1600 1,600mm (63in.)

Before installing the SBD-1 to the fuselage, set

each channel at each servo connector ( SX1~3).

Use the SBC-1 S.BUS channel changer or CIU-2

USB adapter (PC-Link software for setting) to set

the channel.

* S.BUS decoder channel setting is impossible with

the receiver .S.BUS R6108SB

* PC-Link software can be downloaded from the

home page of your region's Futaba importer.

Conventional servo

(or S.BUS servo)

to the receiver S.BUS con-

nection port or S.BUS hub

SX1

SX2

SX3

SBD-1

Servo connector

(Upper)

SX1

(Middle)

SX2

(Lower)

SX3

S.BUS connector

[SBD-1 Ratings]

•Dimensions:

41.8x12.3x8.4mm

(1.65x0.48x0.33in.)

(excluding protruding)

•Weight:

6.9/10.8/14.7/24.5/34.3g

(0.24/0.38/0.52/0.86/1.21oz.)

•Powerrequirement:

Ni-Cd, Ni-MH 4 to 5 ce lls

equivalentbattery(Futaba)

•Op e r a t i n g t e m p e r a t u re

range:-10to+45°

*During channel setting,the LED blinks quickly

(about 5 times/sec). When the LED changes to a

steady light, channel setting is complete.

6 To s e t th e c h an ne l o f ot h e r se r vo

conne ction por ts, quickly p ress an d

release the setting switch and repeat steps

4 and 5.

Channel No. Label

•PutthechannelNo. labelon theservoconnector

fortheidenticationofchannelNo..

Instruction manual (this manual)

*1 S.BUS: Serial communication system for Futaba R/C system

*2 Use the S.BUS hub as the extension code used for the S.BUS servo. Also SBD-1 can be used.

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Radiostyret legetøj
Model:	SBD-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Futaba SBD-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj Futaba Manualer

Futaba R7208SB Manual

16 Juli 2025

16 Juli 2025

8 Juli 2025

8 Juli 2025

8 Juli 2025

Futaba R7214SB Manual

5 Februar 2025

Futaba GY470 Manual

5 Februar 2025

Futaba GYA553 Manual

5 Februar 2025

Futaba SBS-01RO Manual

15 Januar 2025

Futaba 12Z Manual

3 Oktober 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

Spektrum NX20 Manual

1 August 2025

Spektrum Avian 2813-1750Kv Manual

1 August 2025

Spektrum S120 Manual

1 August 2025

Spektrum S6295 Manual

1 August 2025

Spektrum Avian 60 Manual

1 August 2025

Spektrum S1200 Manual

1 August 2025

Spektrum iX20SE Manual

1 August 2025

Spektrum AR20410T Manual

1 August 2025

Spektrum Avian 6362-200Kv Manual

1 August 2025

Carrera Red Hunter X Manual

1 August 2025