Futaba SBS-01RO Manual

Futaba Radiostyret legetøj SBS-01RO

Læs gratis den danske manual til Futaba SBS-01RO (1 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Futaba SBS-01RO, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Use : RPM Sensor

Length 160mm (6.3") ：

Weight 4.9g (0.173oz)：

Voltage : DC3.7 7.4V～

Range : 360 300,000RPM/blades～

SBS-01RO

Double-stick tape × 2

SBS-01RO Sensor Stay

Surface of

rotation

RPM sensor

（Optical type）

1M23N26716

＜ SBS-01RO ＞

Installation

Contents

Wiring

For Helicopter

Number of blades

ID Number Slot Number Setup

Brightness

Surface of

revolution

Less than

150 mm

(5.9”)

Sensor

S.BUS2

Port

Telemetry

S.BUS2 Receiver

Optical perception

part

Instruction Manual

Thank you for purchasing Futaba's SBS-

01RO RPM senso r. This senso r, used

in conjunction with a telemetry enabled

transmitter/receiver, is used to indicate the

number of rotations (propeller, rotor, etc. ) of

the item to which it is attached. The number

of rotations of a model in the sky is a system

which can be checked with a transmitter etc.

To maximize your enjoyment, and to ensure

proper sensing, please read through this

manual thoroughly. We also encourage you to

retain the manual for future reference should

the need arise.

●The SBS-01RO is designed for use

with Futaba telemetry systems.

Sensor

Propeller/Rotor

To receiver S.BUS2 port

󾛽WARNING

󾛹To utilize the SBS-01RO sensor, connect it

to the S.BUS2 port of the Futaba telemetry

enabled receivers.

■The SBS-01RO will not function properly if connected to

an S.BUS port or other channel ports.

󾛹

Be careful of the connector polarity.

■Because of the case construction, reversing the polarity

may cause trouble or sparking from the wiring.

󾛹 Mount the sensor in accordance with the

installation method described below.

■If the SBS-01RO drops out during ﬂight, it cases erratic

operation or loss of control.

󾛹Vibration-proof the PC board and mount the

SBS-01RO where it will not be exposed to

fuel and water.

■Electronic parts are used at the PC board. Take protective

measures against vibration, shock, high temperature, and

so forth.

󾛹 When mount ing t he SB S-01 RO t o the

fuselage, be sure there is som e slack in the

wiring cable.

■If the cable is too tight, vibration may cause the wire to break

or the connector to be dislodged and cause a malfunction.

󾛹 Always perform an operation check after

assembling.

■Do not ﬂy until inspection is complete.

󾙍 Don't touch a sensor during engine motor

rotation.

■When a rotation portion is touched, there is a possibility

of carrying out a large injury.

󾙍 Do not use the SBS-01RO with anything

other than an R/C model.

󾙍 Don't make different connection from a

manual.

■It will break down, if different connection is made.

Please note that the proper default slot for

this accessory is number 2. Information

on how to change the slot assignment is

included in the transmitter's manual.

The SBS-01RO uses an optical

sensor. To operate properly the

prop or rotor being measured must

be fairly brightly lit. Typically the

sensor will not operate properly

indoors, on cloudy days or in early

mornings/late evenings when the

angle of the light striking the prop

or rotor is bad. When one of these

conditions exist, the RPM will be

displayed as 0.

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2012, 11 (3)

The distance between the sensor and the

surface of rotation less than 150 mm.

*Mount the sensor as close as possible to the

prop or rotor.

*The color of the prop or rotor could cause the

RPM to not be detected.

*The SBS-01RO only works in sunlight.

●Sensor Mounting Example

[ Airplane ] [ Helicopter ]

The SBS-01RO may only be used

with telemetry enabled receivers

that o󰮏er S.BUS 2 port. Please refer

to the manual(s) that accompanied

your transmitter and/or receiver for

proper connection methodology.

T h e S B S -01R O i s n o t o p t i m a l f o r

helicopter use due to the large distance

between the rotor and sensor, as a

result, the reading can be unstable. We

recommend the SBS-01RM

magnetic

sensor be utilized for helicopters.

The sensor defaults to two blades. If

the prop/rotor has more than 2 blades

this option must be changed in the

transmitter. (Refer to the transmitters

manual.)

Each sensor has a unique ID number

printed on it. If more than one of the

same type of sensor is utilized in a model,

the ID will need to be input into the

sensor menu of your transmitter.

Sensor stay mounted to a

tail boom using wire ties.

Mount the sensor to the stay using

double-sided tape.

Sensor Stay

Heli Tail pipe

It attaches to the position which

is rotation within the limits of

a main rotor and with which a

stabilizer does not interfere.

Use strong double-sided tape

or screws to mount to the

fuselage of an airplane.

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Radiostyret legetøj
Model:	SBS-01RO

Har du brug for hjælp?

Hvis du har brug for hjælp til Futaba SBS-01RO stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj Futaba Manualer

Futaba R7208SB Manual

16 Juli 2025

16 Juli 2025

8 Juli 2025

8 Juli 2025

8 Juli 2025

Futaba R7214SB Manual

5 Februar 2025

Futaba GY470 Manual

5 Februar 2025

Futaba GYA553 Manual

5 Februar 2025

Futaba SBS-01RO Manual

15 Januar 2025

Futaba 12Z Manual

3 Oktober 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

FMS A6M5 Zero Manual

1 December 2025

FMS 1:12 Toyota FJ45 Manual

1 December 2025

FMS T-28 Trojan V2 Manual

1 December 2025

FMS 1:24 FCX24 Chevrolet K5 Blazer RTR Manual

1 December 2025

1 December 2025

24 November 2025

23 November 2025

14 November 2025

10 November 2025

Axial SCX30 Ford Bronco Manual

29 Oktober 2025