Gamber-Johnson 7170-0166-02 Manual

Gamber-Johnson Ikke kategoriseret 7170-0166-02

Læs gratis den danske manual til Gamber-Johnson 7170-0166-02 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Gamber-Johnson 7170-0166-02, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Rev.N

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

RELOCATION

Top Plate

USB/Audio

Center Brace

12v Knockouts

Center Brace

Top Plate

12v Knockouts

INST-568

1/3

Form

If there is no factory front console plate

7120-0630(included) for required hardware

(Top Plate) installed, use hardware bag

Product Revision

FORD NGPI CONSOLE SEDAN & UTILITY, 2012+

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Printing Spec:

7160-0410, 7160-0412, 7170-0165, 7170-0166

INSTALLATION INSTRUCTIONS

Note:

NOTE: ARMREST AND

CUP HOLDER SHOWN

FOR REF. ONLY

PS-004

Sedan:

1. Remove the stock tunnel plate by removing the

6 bolts.

2. The harness on the right side of the YAW sensor

(located on the transmission tunnel) may impede

box installation. For ease of installation, pull up

on harness to disconnect the push fastener

attaching the harness to the transmission tunnel.

3. The rear mounting points may be hidden under

the flooring. Carefully cut the flooring as shown

to expose the mounting points (Fig 1).

4. Slide console box into place.

5. Attach console to transmission tunnel using OEM

hardware.

Fig 1 - Rear Mounting Bracket, Carpet Cut to Revel Threaded Inserts

Utility:

1. Remove the lower dash trim panels on either side

of the dash (Fig 2).

2. Remove the stock tunnel plate by removing the 6

bolts.

3. Remove the USB/Audio/12v jack Trim Panel (Fig 2)

and disconnect the USB, Audio and 12v cables.

4. Relocate OEM Module to under dash area (Fig. 3)

Fig 2 - Utility Lower Dash

5. The harness on the right side of the YAW sensor

(located on the transmission tunnel) may impede

box insallation. For ease of installation, pull up

on harness to disconnect the push fastener attaching

the harness to the transmission tunnel.

6. Remove the Top Plate from the console box.

7. Slide the console box into place.

8. Attach the console to the transmission tunnel using

the OEM hardware.

9. Attach the Lower Dash Trim Panel to the console box

by placing the lower lip of the Trim Panel into the

hook on the bottom of the console box (Fig 4).

10. Attach the top of the Lower Dash Trim Panel to the

console box using the supplied Trim Hooks (Fig 4).

Note that the left Trim Hook has an "L" cut out of it.

It may be easier to remove the Top Plate when

installing the Lower Dash Trim Panels.

11. Snap the Lower Dash Panels back into place.

2/3

Lower Dash

Trim Panel

USB/Audio

Trim Panel

Fig. 3 - OEM Module located on backside of trim Panel

Produkt Specifikationer

Mærke:	Gamber-Johnson
Kategori:	Ikke kategoriseret
Model:	7170-0166-02
Bredde:	228.6 mm
Dybde:	685.8 mm
Højde:	292.1 mm
Vægt:	14060 g
Velegnet til:	Bil
Produktfarve:	Sort
Produkttype:	Centerhuskonsol
Materiale:	Stål
Farvelægning:	Monokromatisk