Gembird EG-EM1 Manual

Gembird Elmester EG-EM1

Læs gratis den danske manual til Gembird EG-EM1 (4 sider) i kategorien Elmester. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Gembird EG-EM1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Energy Meter
Model No. EG-EM1
Introduction
With the Energy Meter, you are now able to determine power costs of your power loads in the easiest way.
Proper use
The measurement range of the Energy Meter extends from 5W to 3680W. If values fall below or exceed
these limit values, exact measurement are no longer possible. Also the device could not be overloaded,
otherwise will be destroyed. There will be alarm for the power overloading.
The Energy Meter has been developed for monitoring and measuring electrical loads.
The Energy Meter is only certified for operation at 230V AC.
Only power loads with a power supply of 230V AC 50/60Hz may be connected.
The maximum power of any connected load may not exceed 3680W (max. current 16A).
It is only suitable for electrical appliances with resistive load.
Operation of the Energy Meter is only permitted in interior spaces and dry environments, Usage in the
open air is strictly forbidden!
Safety Instructions
This device is not a toy and does not belong to the hands of children.
Only connect the Energy Meter to certified protected contact outlets 230V AC 50/60Hz (10/16A) with a
ground wire.
The connected load may not exceed 3680W(16A).
The recommended operating temperature is between +5 to +40 . High temperature may lead to
overheating and can thereby permanently destroy the Energy Meter.
Avoid operating under adverse environmental temperatures or near flammable gases, vapour and dust.
For reasons of safety, never allow the device to be operated when in wet or in a damp environment
When cleaning or servicing, the device must be disconnected from every source of operating voltage.
Condensers in the device may still be charged, even if the device was disconnected from all voltage
sources.
Do not insert needles, metals or any other objects into the device.
Properties
Display current time (24 hours type), week, load power and cost tariff.
Display total used energy and accrued energy cost.
Display total recorded time, total ON time and percentage .
Dual programmable power tariffs.
Displaying line of power Blinks (fig4,the second line) if the load power is over 3680W
Connection, operation settings
Before you connect the Energy Meter to an outlet or power or power load, condensers in the device will be
charged. Five minutes later, the condensers will have enough power to sustain the normal display of LCD
then the current time and your desired power tariff must be set.
Suggestion:
It is better to take 8-12 hours to charge the condensers fully for the first time, in order
to make the rechargeable Li-batteries to achieve optimum performance.
The procedure for entering the time and power tariff is described as following:
A. The setting of current time and week
1. Press“+” “-“ buttons together to enter into system setting, first setting
is the current time.
2. With “+” button to increase the value of the blinking position, while
with “-“ button to decrease the value of the blinking position.
3. Press “MODE” button to select next position.
4. After the setting of week, press “MODE” button, the system will enter
into the setting of cost tariff 1.
B. The setting of cost tariff 1
1. Set the effect time of cost tariff 1.
2. Set the value of tariff 1.(it is cent as unit, such as: 10cent)
3. With “+” button to increase the value of the blinking position, while
with “-“ button to decrease the value of the blinking position.
4. Press “MODE” button to select next position.
5. Press “MODE” button, the system will enter into the setting of cost
tariff 2.
C. The setting of cost tariff 2
1. Set the effect time of cost tariff 2.
2. Set the value of tariff 2. .(it is cent as unit, such as: 10cent)
3. With “+” button to increase the value of the blinking position from 0 to
9,while with “-“ button to decrease the value of the blinking position.
4. Press “MODE” button to select next position.
5. Go on pressing the button “mode” until the display board of fig4
appears.
D. Press “MODE”, “+” “-” simultaneously to delete all data (the data of current time
and the week will not be deleted) after 5 seconds.

Produkt Specifikationer

Mærke: Gembird
Kategori: Elmester
Model: EG-EM1

Har du brug for hjælp?

Hvis du har brug for hjælp til Gembird EG-EM1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Elmester Gembird Manualer

Gembird

Gembird EG-EM1 Manual

25 Juli 2024

Elmester Manualer

Nyeste Elmester Manualer

Schneider

Schneider METSEPM8213 Manual

18 December 2024
Schneider

Schneider METSEPM8214 Manual

18 December 2024
SIIG

SIIG CE-H23112-S1 Manual

31 August 2024
ORNO

ORNO OR-WE-512 Manual

31 August 2024
Plugwise

Plugwise Sub 803 Manual

27 August 2024
ORNO

ORNO OR-WE-516 Manual

18 August 2024
SolarEdge

SolarEdge MTR-240-1PC1-DW-MW Manual

15 August 2024
Becken

Becken BBPM3007 Manual

10 August 2024
ORNO

ORNO OR-WE-513 Manual

30 Juli 2024
Hager

Hager ECP140D Manual

30 Juli 2024