Gossen Metrawatt SINEAX TV804 Manual

Gossen Metrawatt Måleudstyr SINEAX TV804

Læs gratis den danske manual til Gossen Metrawatt SINEAX TV804 (1 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 74 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 37.5 anmeldelser. Har du et spørgsmål om Gossen Metrawatt SINEAX TV804, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

SINEAX TV804 ENGLISH 2/2

SINEAX TV804

CURRENT CONVERTER

WITH GALVANIC SEPARATION

163 056 10.14

SINEAX TV804 ENGLISH 1/2

General characteristics

• Input current 0…20 mA or 4…20 mA

• Sensors supply in two wires technique: 20 V DC stabilized, 20 mA max.,

protected against short circuit.

• Measure and retransmission or an analog insulated output, current output

0…20 mA or 4…20 mA.

• Indication on the front if there is power supply.

• Insulation 3 wires: 1500 V AC.

Technical data

Power 9…40 V DC, 19…28 V AC, 50…60 Hz, max. 2.5 W

Input Current: 0…20 mA or 4…20 mA, input impedance 20 Ω

Output

Current: 0…20 mA or 4…20 mA,

max. loop impedance 600 Ω

Environmental conditions

Temperature: 0…50 °C, humidity min. 30%, max. 90%

at 40 °C not condensing (see also section “Installation

instruction”)

Errors referred to input’s

measure range

Calibration

0.5%

Thermal coefﬁ cient

0.02% / °C

Linearity

0.05%

Inputs protection Current 100 mA, continuative

Protection

output / power supply

Against pulses overvoltages 400 W/ms

Standards:

Complying equipments with prescriptions:

EN 50081-2 (electromagnetic compability, industrial

environnement)

EN 50082-2 (electromagnetic immunity, industrial

environnement)

Electrical connections

Power

9 - 40 VDC

19 - 28 VAC

2 3

Power voltage must be in a range from 9 to 40 V DC

(indifferent polarity) from 19 to 28 V AC; see also sec-

tion “Installation instructions”.

Upper limits must not be exceeded, if it happen

there could be damages for module.

It is necessary to protect power source from possible

modules failure by fuse correctly dimentioned.

Input

8 9

–

Active input

Connection to be used with transducers 2 wires tech-

nology.

Transducer is directly powered by module 20 V DC

stabilized voltage, 20 mA max., protected against

short circuit.

8 9

–

Passive input

Connection to be used if input current is given from

external (loop power supply is given from external).

Output

5 6

–

Active output

Connection to be used when output loop is to be

directly feeded from module.

Loop power supply given by modules is protected

against short circuit. Max. load resistance 600 Ω.

5 6

–

Passive output

Connection to be used if current loops power supply

is given from external.

Installation instructions

The module is designed to be mounted on a DIN 46277 rail, in vertical

position.

To obtain an optimal working and duration, it is necessary to assure an ade-

quate ventilation to modules, avoiding to place raceways or other objects that

can close abat-vents

Avoid to mount modules over deviced that generate heat; we suggest to mount

devices in the lower side of the panel.

Severe operating conditions

Severe operating conditions are as follows:

• High power voltage (> 30 V DC / > 26 V AC)

• Input sensor feeded

• Use of output in impressed current

When modules are put side by side its possible that it is necessary to sepa-

rate them at least 5 mm in the following cases:

• Upper board temperature higher than 45 °C and at least one of the heavy

working conditions veriﬁ ed.

• Upper board temperature higher than 35 °C and at least two of the heavy

working temperature veriﬁ ed.

Electrical connections

We recommand to use shielded cables to do signals connection; monitor must

be connected to a preferential ground for devices. Besides it is a good rool

avoid to pass wires near power installation cables like inverters, motors, in-

duction furnaces etc..

Dimensions

100 mm

17.5 mm

112 mm

Disposal of Electrical & Electronic Equipment (applicable throughout the

European Union and other European countries with separate collection

programs).

This symbol found on your product or on its packaging, indicates that this

product should not be treated as household waste when you wish to dis-

pose of it. Instead, if should be handed over to an applicable collection

point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences to the environment and human health, which could other-

wise be caused by inappropriate disposal of this product. The re cycling of

materials will help to conserve natural resources. For more detailed infor-

mation about the recycling of this product, please contact your local city

ofﬁ ce, waste disposal service or the retail store where you purchased this

product.

Tel. +41 56 618 21 11

Camille Bauer Metrawatt AG

Fax +41 56 618 21 21

Aargauerstrasse 7 info@cbma

g.com

CH-5610 Wohlen/Schweiz www.camillebauer.com

Produkt Specifikationer

Mærke:	Gossen Metrawatt
Kategori:	Måleudstyr
Model:	SINEAX TV804

Har du brug for hjælp?

Hvis du har brug for hjælp til Gossen Metrawatt SINEAX TV804 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Gossen Metrawatt Manualer

Gossen Metrawatt SECULIFE ST M693A Manual

6 September 2024

Gossen Metrawatt METRALINE EARTH M590R Manual

4 September 2024

Gossen Metrawatt METRA Hit 27Ex Manual

3 September 2024

Gossen Metrawatt METRAOHM 10 Manual

2 September 2024

Gossen Metrawatt POINTAX 6000M Manual

2 September 2024

Gossen Metrawatt METRAHIT CAL Manual

1 September 2024

Gossen Metrawatt PROFITEST PV Manual

1 September 2024

Gossen Metrawatt METRAPhase 1 Manual

1 September 2024

Gossen Metrawatt SECUTEST 21F Manual

1 September 2024

Gossen Metrawatt SECULOAD-N Manual

1 September 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025