Graco SaniSpray HP 20 Manual

Graco Ikke kategoriseret SaniSpray HP 20

Læs gratis den danske manual til Graco SaniSpray HP 20 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 100 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 50.5 anmeldelser. Har du et spørgsmål om Graco SaniSpray HP 20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

ti38477a

Read the sprayer manual 3A7646 (corded) or 3A7649 (cordless)

for complete instructions and warnings. This Quick Guide is not

a substitute for reading and understanding all instructions and

warning labels supplied with the equipment.

CHEMICAL HAZARD: Follow chemical warnings on disinfec-

tant container label and as listed in manual. Do not spray

humans or animals. Wear protective equipment.

FIRE AND EXPLOSION HAZARD: Do not use any alcohol-based

or other ﬂammable liquid in corded sprayer. Follow ﬁre and

explosion warnings as listed in your manual.

SKIN INJECTION HAZARD: High pressure equipment. Keep

clear of spray tip and leaks. Follow the Pressure Relief

Procedure whenever you stop spraying.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN

SERIOUS INJURY, AMPUTATION, OR DEATH.

WARNING

NOTICE

Do not run sprayer without ﬂuid.

Running the sprayer dry will cause damage to the pump.

Disinfectant left in the sprayer will damage the sprayer. To avoid

damage, always completely ﬂush with warm water after every use.

Do not store sprayer with disinfectant in it.

Foam in disinfectant may cause operation issues that could damage

the sprayer. Wait until foam has subsided to ﬁll FlexLiner.

KNOW YOUR CONTROLS

Spray Tip

Guard

Pump

Filter

Cup lid

Cup Support

Prime Knob

Trigger

Speed

Control

VacuValve™

FlexLiner™

Pressure Relief Procedure

Follow this procedure whenever instructed

to perform PRESSURE RELIEF PROCEDURE.

Disconnect power (unplug cord

or remove battery).

Turn Prime Knob down to PRIME

position to relieve pressure.

To begin a new job, ﬁrst

perform the PRESSURE

RELIEF PROCEDURE.

Insert one FlexLiner into the

Cup Support and ﬁll with

properly diluted disinfectant.

• NOTE: Verify there is no

damage, such as a crease, on

the top surface of the FlexLiner.

If damaged DO NOT USE.

Prime the pump with disinfectant

as follows:

A. Verify Prime Knob is pointed down

to PRIME position.

B. Plug the sprayer into a grounded

power source or install a fully

charged battery onto the sprayer.

C. Turn the sprayer upside down.

• Pull the Trigger for 5 seconds.

• NOTE: Disinfectant will not spray

out, but will recirculate through

the pump and back into the cup.

D. Turn the sprayer upright and open

the VacuValve cap.

E. Tilt the sprayer so the VacuValve

is the highest point.

F. Gently squeeze the FlexLiner until

disinfectant enters the VacuValve

reservoir and all air is evacuated

from the cup.

G. While continuing to squeeze

the FlexLiner, close the

VacuValve cap.

• NOTE: If FlexLiner is not

squeezed while VacuValve Cap is

open, air will quickly pull into the

FlexLiner. If any air bubbles are

visible in the cup, repeat steps

E-G.

Firmly tighten Cup Lid onto

Cup Support to ensure an

air tight seal.

Turn Prime Knob forward to

SPRAY position.

Verify Spray Tip is forward in

the SPRAY position.

Pull the Trigger to verify disinfectant

sprays from the sprayer. If sprayer

does not spray within 5 seconds,

STOP and repeat START UP.

YOU ARE NOW READY TO SPRAY!

Install the cup onto the sprayer:

A. Verify Pump Filter is installed

and clean.

B. Align VacuValve (on Cup Lid)

with Prime Knob (on sprayer).

C. Push cup assembly onto the

sprayer. Twist to lock.

Review Important User Information in your sprayer manual to understand

which types of disinfectants are compatible with your sprayer.

This sprayer arrives from the factory with a small amount of test ﬂuid

in the system. It is important that you ﬂush the sprayer with warm

water before using for the ﬁrst time. See Flushing a New Sprayer in

your sprayer manual.

Refer to disinfectant label for manufacturer’s directions on proper use. If

dilution is required, properly dilute disinfectant in a separate container.

START UP

START UPcontinued

AIRLESS HANDHELD

www.graco.com/techsupport

NOTE: Disinfectant left in the sprayer will damage the sprayer. To avoid

damage, always completely ﬂush with warm water after every use.

See Cleanup and Storage in your sprayer manual.

Do not store sprayer with disinfectant in it.

Make certain the sprayer is plugged into a grounded power

source or has a fully charged battery installed.

If the sprayer does not spray, try the steps below:

Verify Cup Lid is tight. An under tightened Cup Lid will allow air

to seep into the FlexLiner and cause a loss of prime.

Make certain there is no damage, such as a crease, on the top

surface of the FlexLiner. If damaged, DO NOT USE.

Make certain the Spray Tip is not plugged. See Clear Tip Clogs in

your sprayer manual for instructions on how to reverse and

easily clear a clog.

Make certain there is only one FlexLiner in the Cup Support.

Multiple FlexLiners nested tightly together can go unnoticed.

Repeat START UP step 5 to ensure all air is evacuated from the

FlexLiner.

If necessary, replace VacuValve cap. Two new VacuValve caps

came with your sprayer.

See Troubleshooting in your sprayer manual for more

information.

Make certain the Cup Lid is properly threaded to the Cup

Support. If threads are visible below the Cup Lid when tight,

then the Cup Lid is cross-threaded.

HOW TO SPRAY

CUP REFILLS

CLEANUP AND STORAGE

CLEANUP AND STORAGE TROUBLESHOOTING

Review How To Spray in your sprayer manual. continued

Adjust the Spray Tip Guard for

desired horizontal or vertical

spraying direction.

Point sprayer toward the

surface to be sprayed.

Remove cup assembly from

the sprayer. Set sprayer

on a rag.

Remove Cup Lid from Cup

Support and reﬁll with

properly diluted disinfectant.

Follow START UP instructions

to proceed.

Set the Speed Control to

the lowest setting.

Pull and hold the Trigger

and slowly increase the

Speed Control to the minimum

setting necessary to produce

an acceptable spray of

disinfectant.

Adjust the sprayer’s distance

from the surface and your

hand speed to achieve the

desired surface coverage.

To reﬁll the cup, ﬁrst perform the PRESSURE RELIEF PROCEDURE.

To clean your sprayer, ﬁrst perform the PRESSURE RELIEF

PROCEDURE.

Remove cup assembly from the sprayer. Set sprayer on a rag.

Remove Cup Lid from Cup Support

and pour excess disinfectant into

waste bucket.

You can either dispose of the used

FlexLiner and install a new FlexLiner,

or clean a used Flexliner.

Fill FlexLiner with warm water.

Firmly tighten Cup Lid onto Cup

Support to ensure an air tight seal.

Verify Prime Knob is downward

in PRIME position and set Speed

Control to #10 setting.

Turn the sprayer upside down.

A. Point the sprayer into a waste bucket.

B. Pull the Trigger for 10 seconds

to clean pump.

• NOTE:

Water will not spray out,

but will recirculate through the

pump and back to the cup.

Turn Prime Knob forward to SPRAY.

A. With sprayer upside down point

into a waste bucket.

B. Pull the Trigger for 10 seconds,

spraying into the waste bucket.

C. Reverse the Spray Tip to the

UNCLOG position and with sprayer

upside down, spray into the

waste bucket for 30 seconds.

• NOTE: Do not run sprayer without

ﬂuid. Running the sprayer dry will

cause damage to the pump.

A. Turn Prime Knob to PRIME

position and disconnect power

(unplug cord or remove battery).

B. Dispose of all waste ﬂuid

according to the instructions on

the disinfectant container label

and applicable regulations.

Remove and clean the Spray Tip, Spray Tip Guard, Pump Filter,

Cup Support and Cup Lid with warm water. Clean the outside of

the sprayer with a soft cloth moistened with warm water.

Install the cup onto the sprayer.

3A7929 Revision E, October 2020, Original Instructions. This Quick Guide contains English.

Produkt Specifikationer

Mærke:	Graco
Kategori:	Ikke kategoriseret
Model:	SaniSpray HP 20

Har du brug for hjælp?

Hvis du har brug for hjælp til Graco SaniSpray HP 20 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Graco Manualer

Graco 244161 Manual

29 September 2025

Graco TC Pro Corded 17N163 Manual

28 September 2025

Graco TC Pro PLUS Cordless 17N223 Manual

27 September 2025

Graco Trabon 24B496 Manual

1 September 2025

Graco InvisiPac HM50 24Y118 Manual

20 Juli 2025

Graco SmartSense Soothing Bassinet Manual

10 Juli 2025

Graco Crib Conversion Kit Manual

9 Juli 2025

Graco Cradle Me Lite 3-in-1 Manual

9 Juli 2025

Graco SmartSense Swing Manual

9 Juli 2025

Graco Teddi Changing Table Manual

6 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Shape ALPKIT Manual

19 Oktober 2025

Shape COMPOFIC Manual

19 Oktober 2025

ResMed AirFit F10 Manual

18 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Shape BP0008EVF Manual

18 Oktober 2025

ResMed Mirage Micro Manual

18 Oktober 2025

AstralPool Swimspa Compact Manual

18 Oktober 2025

ResMed Chin Restraint Manual

18 Oktober 2025

Shape FS5BASEKIT Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025