GW Instek PEL-3032E Manual

GW Instek Måling PEL-3032E

Læs gratis den danske manual til GW Instek PEL-3032E (2 sider) i kategorien Måling. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om GW Instek PEL-3032E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

GW INSTEK PAR NO. 82EL T -3KE00M 1

This section contains the basic safety symbols that may

appear on the accompanying User Manual CD or on the

instrument. For detailed safety instructions and

precautions, please see the Safety Instructions chapter

in the user manual CD.

These safety symbols may appear in the user manual or

on the instrument.

Warning: Identifies conditions or

practices that could result in injury or

loss of life.

Caution: Identifies conditions or

practices that could result in damage

to the instrument or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Earth (ground) Terminal

Frame or Chassis Terminal

Do not dispose electronic equipment

as unsorted municipal waste. Please

use a separate collection facility or

contact the supplier from which this

instrument was purchased.

When using the instrument in the United Kingdom,

make sure the power cord meets the following safety

instructions.

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed as

follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

loured Green/Green & Yellow. or co

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable of

0.75mm2

should be protected by a 3A or 5A fuse. Larger conductors

would normally require 13A types, depending on the connection

method used.

Any exposed wiring from a cable, plug or connection that is engaged

in a live socket is extremely hazardous. If a cable or plug is deemed

hazardous, turn off the mains power and remove the cable, any

fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

The Getting Started chapter introduces the instrument’s

main features, appearance, and set up procedure.

The PEL-3000E is an economic, standalone, high

performance DC electronic load positioned to test a

wide range of different power sources. The DC

electronic load is fully programmable to simulate

anything from basic static loads to complex dynamic

loads. The PEL-3000E is extremely robust and capable

of molding to any test environment.

PEL 3031E-

1V-150V

6A (Low range)

60A (High range)

300W

PEL 303- 2E

2.5V-500V

1.5A (Low range)

15A (High range)

300W

•High slew rates of up to 2.5A/μs

for a fast response speed -(PEL

3031E)

•High resolution – 16 bit

•7 operating modes: CC, CV, CR,

CP, CC+CV, CR+CV, CP+CV

•Fully programmable with normal

and fast sequences

•Soft start

•Dynamic mode

•OCP, OVP and other protection

features

•Remote sense

•Integrated meter

•Rack-mountable

•USB and GPIB

•External voltage or resistance

control

•Rear panel trigger in/out BNC

•Analog external control

Mode

I Range

H 60A

V Range

L 15V

Function

Static Configure

0.0000V

0.000A

0.00w

SlewRate 2500

CC B Value 0.000

CC A Value 0.000

LOADUSB

A Value

Fine

mA/us

1. Main frame status

panel

2. Operation status

panel

3. Soft keys

4. Setting area

5. Measurement area

Use the following when first using the procedures

PEL- E to power up the instrument, restore the 3000

factory default settings and check the firmware

version. Lastly, the Conventions section will introduce

you to the basic operating conventions used

throughout the user manual.















 



 















  

1. J1 Frame control

ports

2. TRIG OUT BNC

3. TRIG IN BNC

4. Exh aust fan

5. Power socket and

switch

6. GPIB (optional)

7. USB device port



















































 





 









 

 







P E L - 3 0 3 1 E





  

1. Air inlet

2. LCD Display

3. Function keys

4. Power key

5. Main/Local key

6. FUNC/File key

7. Help/Utility key

8. Short key

9. Load On/Off

10. Scroll wheel

11. Number pad,

Clear/Lock and Enter

keys

12. USB port, Preset and

Shift keys

13. Sense-, Sense+

terminals

14. Input terminals

User /Programming Manual CD

Quick Start Guide (this document)

Power C ord x1

Region Dependent

Front terminal washers ( M6) x2

61SF-062104N1

Remote sense cables, red x1, black

GTL- 105A

GPIB cable, 2.0m

GTL- 248

USB ca , Type A - ble Type B

GTL- 246

Dust filter

PEL 010-

GPIB option

PEL 004-

This manual contains proprietary information, which is

protected by copyright. All rights are reserved. No part

of this manual may be photocopied, reproduced or

translated to another language without prior written

consent of Good Will Corporation.

The information in this manual was correct at the time

of printing. However, Good Will continues to improve

its products and therefore reserves the right to change

the specifications, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd. No. 7-1, Jhongsing Rd., Tucheng

Dist. New i ., Taipei C ty 236, Taiwan

Produkt Specifikationer

Mærke:	GW Instek
Kategori:	Måling
Model:	PEL-3032E

Har du brug for hjælp?

Hvis du har brug for hjælp til GW Instek PEL-3032E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måling GW Instek Manualer

GW Instek GPM-8310 Manual

20 Juli 2025

GW Instek GPT-12004 Manual

1 Februar 2025

GW Instek GPT-12003 Manual

1 Februar 2025

GW Instek GPT-12002 Manual

1 Februar 2025

GW Instek GPT-12001 Manual

1 Februar 2025

GW Instek PEL-3032E Manual

15 November 2024

Måling Manualer

Nyeste Måling Manualer

PeakTech 5605 A Manual

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

Mitsubishi SRK25ZSH-WF Manual

16 December 2025

Mitsubishi SRK71ZRH-WF Manual

15 December 2025

Mitsubishi SRK50ZSXH-WF Manual

15 December 2025