Havis C-3090-4 Manual

Havis Bilsæt C-3090-4

Læs gratis den danske manual til Havis C-3090-4 (4 sider) i kategorien Bilsæt. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Havis C-3090-4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION INSTRUCTIONS C- - 3090’s & C 3089’s

COMPUTER LAPTOP MOUNT AND ACCESSORIES

TOOLS NEEDED:

Ratcheting wrench

Standard socket set

Open-end wrench set

Allen wrench set

Screwdriver set

Always!

 Read all instructions before installing any Havis, Inc. products.

 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!

 Use hardware provided with install kit

1. MOUNTING C-3090-3 or 4 & C-3089-3 or 4 to C- TCB’S

Photo #3 on page #2 is a basic assembly

instruction of a C-3090-3 (w/ tilt/swivel)

mounting to a C-TCB-x.

The tilt/swivel assembly, ( , which Photo #1)

comes pre-assembled to the C-3090 from the

factory, will bolt directly to the rotating plate,

using the hardware loosely attached to the

plate. You do not need to unassembled the

tilt/swivel from the C-3090.

Note: Be sure the 2” fender washer is assembled between

the rotating plate and the tilt/swivel assembly.

2. C-3090-1 or 2 & C-3089-1 or 2 MOUNTING TO

VEHICLE TUNNEL PLATES:

The C-3090 will come pre-assembled with

tilt/swivel attached.

Mount trak kit into vehicle.

Place console and C-3090 into desired

position on trak. (Photo #2)

Note: Be sure assembly does not interfere with dash or

console.

Slide ¼-20 hex nuts into slots on side of trak

in location to mount C-3090.

Attach C-3090 to trak using ¼-20 x ½” hex

bolts and washers. Tighten in desired area.

Photo #1

Photo #2

C-3090_INST_6-09.docx6- 09

3. ADJUST C-3090 PLATFORM FOR SPECIFIC LAPTOP:

The C-3090 will need to be adjusted to

properly hold your particular laptop.

Note: Do not adjust the latch on the underside of the

laptop.

Loosen the “L” clamps on the sides of

the C-3090. (Photo #4)

Release the latch on the underside of the

laptop.

Place laptop on top of C-3090 platform

and close the latch.

Open laptop and adjust “L” clamps so

they are ﬁrm against inside lip of

computer on the latch side.

Loosen ¼-20 nylock nuts on the plate on underside of laptop assembly and adjust to

width of laptop.

Photo #3

Produkt Specifikationer

Mærke:	Havis
Kategori:	Bilsæt
Model:	C-3090-4

Har du brug for hjælp?

Hvis du har brug for hjælp til Havis C-3090-4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilsæt Havis Manualer

Havis PKG-PSM-118 Manual

3 September 2024

Havis C-HDM-201 Manual

3 September 2024

Havis C-HDM-183 Manual

3 September 2024

Havis C-HDM-407 Manual

3 September 2024

Havis C-VS-1600-EXPL Manual

3 September 2024

Havis DS-DA-409 Manual

3 September 2024

Havis C-HDM-204 Manual

3 September 2024

Havis UT-X-SD-KIT-1 Manual

3 September 2024

Havis C-HDM-141 Manual

3 September 2024

Havis PKG-PSM-144 Manual

3 September 2024

Bilsæt Manualer

Nyeste Bilsæt Manualer

Metra 99-8270HG Manual

3 April 2025

Metra 99-8722B Manual

3 April 2025

Metra 99-7802CH Manual

3 April 2025

Metra 99-8214TG Manual

3 April 2025

ZZ-2 IC-SYM Manual

1 April 2025

Metra 99-4000 Manual

31 Marts 2025

Exibel INBTK006 Manual

14 Januar 2025

Metra 95-5026 Manual

28 December 2024

Metra 95-7883HG Manual

28 December 2024

Scosche HA1714B Manual

28 December 2024