Havis C-HDM-186 Manual

Havis Ikke kategoriseret C-HDM-186

Læs gratis den danske manual til Havis C-HDM-186 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Havis C-HDM-186, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
A-
GUIDE RING BUSHING REMOVAL
WE STRONGLY RECOMMEND NOT TO REMOVE THE
GUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLE
IS DESIRED - FOLLOW THIS SIMPLE REMOVAL
INSTRUCTION
INSERT MAXIMUM 1" DIAMETER OBJECT WITH
1.
SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.
MAKE SURE NOTHING PREVENTS GUIDE RING
2.
BUSHING FROM BEING EJECTED UNDERNEATH. HIT
WITH A HAMMER TO FORCE THE GUIDE RING
BUSHING OUT.
7/8" - 1"
DIAMETER
OBJECT
SUPPORT ARM
(OPTIONAL)
B -
INSTALL SPIDER COLLAR (OPTIONAL
COMES WITH C-HDM-401 & 403)
IF MOUNTING THE SPIDER COLLAR TO THE INNER
1.
POLE USE CM003406 REDUCING BUSHING. SPREAD
AND SNAP OVER THE INNER POLE.
LOOSELY ATTACH SPIDER COLLAR TO THE OUTER
2.
POLE OR CM003406. DO NOT MOUNT SPIDER
COLLAR ABOVE OUTER POLE HORIZONTAL CUT.
SPIDER MUST BE
BELOW THIS SLOT
ON THE OUTER POLE
C -
INSTALL OPTIONAL C-HDM-416
IF MOUNTING C-HDM-416 TO THE INNER POLE USE
1.
CM003406. SPREAD THE PIECE AND IT SHOULD SNAP
OVER THE INNER POLE.
ATTACH C-PM-101 TO CLAMP ASSEMBLY USING
2.
LONG CARRIAGE BOLTS INSERTED THROUGH THE
PRINTER AND ONE PIECE OF EXTRUSION.
ATTACH POLE CLAMP TO THE OUTER POLE OR
3.
CM003406. AFFIX SECOND PIECE OF EXTRUSION
AROUND POLE AND LOOSELY TIGHTEN THE
HARDWARE. DO NOT MOUNT CLAMP ABOVE
OUTER POLE HORIZONTAL CUT.
CM003406 REDUCING
BUSHING IS NECESSARY
IF MOUNTING TO
THE INNER POLE.
(USE ONLY ON FIXED
HEIGHT POLES)
C-PM-101
SOLD SEPARATELY
D-
INSTALL GAS SHOCK (OPTIONAL)
(SKIP IF GAS SHOCK IS NOT IN USE)
1.
UNSCREW SMALL PLASTIC DISC FROM SHOCK
2.
INSERT GAS SHOCK ASSEMBLY UPWARD FROM
THE BOTTOM OF HDM POLE ASSEMBLY WITH GAS
SHOCK'S ROD FACING DOWNWARD. GAS
SHOCK WILL SANDWICH BETWEEN MOUNTING
BASE C-HDM-100 SERIES (NOT SHOWN) AND
ACTION ADAPTER C-HDM-300 SERIES (NOT
SHOWN).
ONCE GAS SHOCK SITS PROUD OF THE INNER
3.
POLE REATTACH SMALL PLASTIC DISC
GAS SHOCK
(OPTIONAL)
E -
INSTALL C-HDM-409 OPTIONAL
& COLLAR CLAMP ALIGNMENT
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE C-HDM-409.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
F -
INSTALL C-HDM-410-412 OPTIONAL
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE OFFSET.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
45°
MAX.
45°
MAX
SLOTS IN TUBE
AND CLAMP
ALIGNED
HAMMER
PROJECT #
REV.
DESCRIPTION
DATE
BY
CHECKED BY
1765
3-13
REVISION DATE CORRECTED TO PT895 DOCUMENTED CHANGE.
NO OTHER CHANGES
8/5/2014
KDAVIS
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 8.362
TITLE:
DWG. NO.
C-HDM_INST
REV
A
3-13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES

Produkt Specifikationer

Mærke: Havis
Kategori: Ikke kategoriseret
Model: C-HDM-186
Produktfarve: Sort
Pakkevægt: 4990 g
Normal brug: Bil

Har du brug for hjælp?

Hvis du har brug for hjælp til Havis C-HDM-186 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Havis Manualer

Havis

Havis C-HDM-176 Manual

12 September 2025
Havis

Havis UT-1003-KIT Manual

12 September 2025
Havis

Havis SC-1000-ACC-03 Manual

11 September 2025
Havis

Havis C-MD-121 Manual

11 September 2025
Havis

Havis DS-GTC-212 Manual

11 September 2025
Havis

Havis C-DMM-2005 Manual

11 September 2025
Havis

Havis C-HDM-145 Manual

16 Februar 2025
Havis

Havis C-DMM-2004 Manual

16 Februar 2025
Havis

Havis C-DMM-125 Manual

16 Februar 2025
Havis

Havis CST00215 Manual

30 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Eschenbach

Eschenbach laboCLIP Manual

30 Oktober 2025
Iogear

Iogear GearPower GPAWC145W Manual

30 Oktober 2025
DeWalt

DeWalt DWST83471 Manual

30 Oktober 2025
Elvid

Elvid SignalMaster UDX-HS Manual

30 Oktober 2025
First Alert

First Alert SMCO600NV Manual

30 Oktober 2025
ROCWARE

ROCWARE RM702 Manual

29 Oktober 2025
Trinnov

Trinnov D-MON Manual

29 Oktober 2025
Meliconi

Meliconi Base Wash Evo Manual

29 Oktober 2025
Olimpia Splendid

Olimpia Splendid Bi2 SL AIR Manual

29 Oktober 2025
Abus

Abus C523–C526 Manual

29 Oktober 2025