Henry Engineering Mike Alert Manual

Henry Engineering Ikke kategoriseret Mike Alert

Læs gratis den danske manual til Henry Engineering Mike Alert (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 51 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 26 anmeldelser. Har du et spørgsmål om Henry Engineering Mike Alert, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MIKE ALERT

HENRY ENGINEERING

Microphone Tally Light Controller

PO Box 3796

Seal Beach, CA 90740

Tel: 562.493.3589

www.henryeng.com

DESCRIPTION

Mike Alert is an interface unit for controlling the dual-color tally lights on “MIKA” microphone arms. The Mike Alert

unit allows two mic arm tally lights to be independently controlled, and provides power and control circuitry to

operate the white and red tally indicators in each mic arm.

WARNING! For 230V operation, change mains voltage jumpers before connecting to AC power!

Remove jumpers between E6 & E7, and between E5 & E8. Install a jumper between E5 & E6 for 230V; replace

fuse with a .125a fuse. See schematic on reverse side. Jumpers should be changed by a qualified technician only.

INSTALLATION

Connect each MIKA mic arm to the 5-pin female XLR Input connector. Wire the cable from the MIKA mic arm to a

5-pin male XLR connector as follows:

Pin 1 = Mic ground (Ties to Pin 1 of Mic Output connector)

Pin 2 = Mic audio + (Ties to Pin 2 of Mic Output connector)

Pin 3 = Mic audio – (Ties to Pin 3 of Mic Output connector)

Pin 4 = Tally light BLACK wire

Pin 5 = Tally light ORANGE wire

Note: Mic audio will be passed-through to the 3-pin male XLR Output connector on the Mike Alert unit.

All tally light control inputs are via the 15-pin D Control connector. There are two inputs for each mic arm. One

input activates the WHITE tally light, the second input activates the RED tally light. All control inputs are opto-

isolated. Control inputs can be either a maintained DC voltage (5-12 vdc) or a contact closure or open collector.

For control via maintained DC voltage, connect to the + and – input terminals only. (Input Z = 2k ohms)

Pin 1: MIC 1 WHITE + Pin 5: MIC 2 WHITE + Pin 9: +12V SOURCE Pin 13: +12V SOURCE

Pin 2: MIC 1 WHITE - Pin 6: MIC 2 WHITE - Pin 10: GROUND Pin 14: WHITE Output

Pin 3: MIC 1 RED + Pin 7: MIC 2 RED + Pin 11: +12V SOURCE Pin 15: RED Output

Pin 4: MIC 1 RED - Pin 8: MIC 2 RED - Pin 12: GROUND

For control via an external contact closure or open collector, connect the + input(s) to any +12V SOURCE pin.

Connect the closure between the – input(s) and any GROUND pin. (The external contact closure completes the

circuit to ground, using the Mike Alert as a power source.)

Pins 14 & 15 are “master outputs” for the WHITE and RED tally indicators. These outputs provide 12 vdc whenever

either the white or red tally outputs is active. These outputs can be connected to a Henry Engineering

SUPERELAY to activate the studio’s main On The Air tally light. If multiple Mike Alert units are used, these outputs

can be bused together so that the main On The Air light will turn on when ANY microphone is in use. Connect Pin

14 and/or Pin 15 to the Superelay’s IN+ control input. Connect any GROUND pin of the Mike Alert to the Superelay

G input.

OPERATION

Mike Alert will activate the MIKA tally lights when it receives a control input. All inputs must be maintained (not a

momentary pulse). Note that the RED input will always take precedence: if the WHITE and RED inputs are both on

at the same time, only the RED tally light will operate. The LEDs on the front of the unit will indicate which tally

lights are active. (Yellow LED = WHITE; Red LED = RED)

Produkt Specifikationer

Mærke:	Henry Engineering
Kategori:	Ikke kategoriseret
Model:	Mike Alert

Har du brug for hjælp?

Hvis du har brug for hjælp til Henry Engineering Mike Alert stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Henry Engineering Manualer

Henry Engineering Talent Pod II Manual

28 September 2025

Henry Engineering SuperLight Manual

25 December 2024

Henry Engineering MultiPhones Mini Pod Manual

25 December 2024

Henry Engineering Autoswitch Manual

25 December 2024

Henry Engineering LogiConverter Manual

25 December 2024

Henry Engineering SUPERELAY II Manual

25 December 2024

Henry Engineering SportsCaster Manual

7 December 2024

Henry Engineering TwinMatch Manual

20 November 2024

Henry Engineering Mike Alert Manual

6 September 2024

Henry Engineering MultiPort Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW PROPULLATOR 2500MH Manual

3 November 2025

ANCEL HD3200 Manual

3 November 2025

Lantronix C3220 Manual

3 November 2025

Cooler Master MasterBox MB511 Manual

3 November 2025

Klarstein La Palma 750 Smart Manual

3 November 2025

ANCEL AD610 Elite Manual

3 November 2025

ErgoAV ERIWA1-01W Manual

3 November 2025

QOLIXm YQAWSL-6A4U Manual

3 November 2025

ANCEL AJ400 Manual

3 November 2025

Emerson ITL9907RE Manual

3 November 2025