Henry Engineering MultiPhones Guest Pod II Manual

Henry Engineering Ikke kategoriseret MultiPhones Guest Pod II

Læs gratis den danske manual til Henry Engineering MultiPhones Guest Pod II (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Henry Engineering MultiPhones Guest Pod II, eller vil du spørge andre brugere om produktet?

Side 1/2
MULTIPHONES GUEST POD II
HEADPHONE AMPLIFIER with TALENT CONTROL
DESCRIPTION
The MultiPhones Guest Pod II is an individual headphone listening station for use with the MultiPhones Distributed
Headphones System. It features a high performance headphone amplifier, plus two illuminated pushbuttons that
are typically used by talent for Cough and Talkback functions. When used with the MultiPhones Master unit,
power and audio are supplied by the Master. The Guest Pod can also be used as a stand alone headphone
listening station (without a MultiPhones Master unit) if other powering is provided. The Guest Pod includes a Level
control and both ¼ and 3.5mm headphone jacks.
The Guest Pod II is designed for tabletop, under-counter, or r tabletop use, install the in-cabinet installation. Fo
rubber feet on the bottom of the enclosure. Another option is to install two #8 screws in the tabletop, 3 apart, and
slide the unit onto the screw heads. For under-counter installation, open the Guest Pod enclosure by removing the
four corner screws from the bottom of the unit. Remove the top of the clamshell enclosure. Drill screw holes in the
top as necessary and screw the top to the underside of the countertop. Re-attach the lower section to the top with
the bottom screws.The Guest Pod II can also be mounted into cabinetry using the optional Cabinet Mounting Plate.
For use with MultiPhones Master unit: The Guest Pod(s) is connected to the MultiPhones Master unit using cat5
cabling. In most cases, unshielded cables can be used. WARNING! DO NOT USE CROSSOVER CABLES.
Connect up to 3 Guest Pods directly to the MultiPhones Master unit. Each Guest Pod has 2 RJ45 connectors,
which are wired in parallel. (Use either connector.) Additional Guest Pods can be daisy chained together in any
combination. The total number of Guest Pods connected to one MultiPhones Master should not exceed 12 units.
For use as a stand alone headphone listening station: For stand alone use, the Guest Pod requires a
power source. Henry Engineerings transformer may be used. The PowerPod will PowerPod or any 9-12 volt AC
power up to 12 Guest Pods. If a 12V AC transformer is used, each Guest Pod will require about 50 mA.
Two ¼ TRS input jacks on the rear panel accept stereo balanced audio at about 0 dBu.
Wire the inputs as follows: Tip = High; Ring = Low; Sleeve = Ground.
Multiple Guest Pods can be used by daisy chaining them together with cat5 cabling. Both power and audio will be
distributed to all Guest Pods via the cat5 cables. (To distribute power but not audio, remove R1, R19, R21, & R22
from each Guest Pod unit in the system.)
Talent control buttons: The two talent buttons (Cough and Talkback) must be wired to the Control RJ45
connector by the user. Any pin-out can be accommodated. Install wires between the switch terminals and the PC
board pads labeled , which correspond to the pins on the Control RJ45 connector. Be sure to install a W1 thru W8
resistor in series with the LED in each switch according to the tally supply voltage being used. (12vdc = 2K ohms.)
See the schematic on the reverse side for switch terminal details.
OPERATION
The Guest Pod II is simple in its operation. The LEVEL controls adjust the audio level to the PHONES jacks. Do
not use both jacks at the same time. Use headphones with an impedance between 24 and 600 ohms.
Do not use older 8-ohm headphones. Excessive listening levels can cause permanent hearing damage!
SPECIFICATIONS
INPUT From MultiPhones Master unit or
¼ TRS jacks, 2X, 0 dBu, balanced 20K
OUTPUT For 24 600 ohm headphones, ¼ and 3.5mm jacks
FREQUENCY RESPONSE 5 Hz 20 kHz, +/- 0.25 dB
DISTORTION .005% typical
NOISE -80 dBm typical
POWER INPUT Supplied by MultiPhones Master unit, PowerPod,
or 9-12 VAC transformer, 50mA per unit
PHYSICAL DIMEN 5.75w X 1.75h X 6.0d, 1 LB
MOUNTING PLATE 5.5w X 1.5h, 6.0 behind panel; cutout: 4.5w X 1.0h (optional)
Specifications subject to change without notice. Rev. 1/19
HENRY ENGINEERING
PO Box 3796
Seal Beach, CA 90740
Tel: 562.493.3589
www.henryeng.com
TM


Produkt Specifikationer

Mærke: Henry Engineering
Kategori: Ikke kategoriseret
Model: MultiPhones Guest Pod II

Har du brug for hjælp?

Hvis du har brug for hjælp til Henry Engineering MultiPhones Guest Pod II stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Henry Engineering Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

T'nB

T'nB VINEKIT Manual

16 September 2025
T'nB

T'nB PADA36W Manual

16 September 2025
T'nB

T'nB TCUNSAM Manual

16 September 2025
T'nB

T'nB MHFIXDUAL Manual

15 September 2025
T'nB

T'nB MHFLEX Manual

15 September 2025
T'nB

T'nB ANIN02 Manual

15 September 2025
T'nB

T'nB TCUNVES Manual

15 September 2025
T'nB

T'nB NBSTANDFLEX Manual

15 September 2025
T'nB

T'nB TCUN01 Manual

15 September 2025