Hikoki NT65M2 Manual

Hikoki Hæftemaskine NT65M2

Læs gratis den danske manual til Hikoki NT65M2 (13 sider) i kategorien Hæftemaskine. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Hikoki NT65M2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/13
Finish Nailer
Model NT 65M2
Handling instructions
Note:
Before using this Pneumatic Power Tool, carefully read through
these HANDLING INSTRUCTIONS to ensure efficient, safe operation.
It is recommended that these INSTRUCTIONS be kept readily
available as an important reference when using this power tool.
2
GENERAL OPERATIONAL PRECAUTIONS
1. Operate the power tool safely for correct uses.
Do not use the power tool for uses other than
those specified in this instructions.
2. For safe operation handle the power tool correctly.
Please follow the instructions given in this
instruction manual and correctly handle this tool
so as to ensure safe operation. Never let the tool
be use by children or people who do not know
enough to be able to handle it correctly, or let
it be used by people who cannot operate it
correctly.
3. Confirm the safety of the workshop.
Keep unauthorized people away from the
workshop. Especially children should be kept away.
4. The right parts in the right places.
Do not remove any of the covers or screws. Keep
them in place as they have their functions.
Moreover, because it would be dangerous, never
make modifications to the tool or use it after
making modifications.
5. Check the tool before using it.
Before using the tool, always check that no parts
of it are broken, that all screws are completely
tight, and that no parts are missing or rusty.
6. Excessive work could cause accidents.
Do not make tools and accessories work beyond
their abilities. Excessive work not only damages
the power tool but also is dangerous in itself.
7. Stop operation immediately if abnormalities are
noticed.
Stop operation if you notice abnormalities, or if
the power tool does not work properly; have the
power tool inspected and serviced.
8. Look after the power tool carefully.
If you drop or knock the power tool against things,
the outer frame may be deformed and cracks or
other kinds of damage may occur, so please handle
it with sufficient care. Also, do not scratch or
engrave signs on the power tool. Owing to high
pressure air inside the tool, cracks in the surface
are dangerous.
Never use the power tool if a crack develops or
if air is escaping from a crack.
9. Take good care for a long life.
Always take good care of the power tool and keep
it clean.
10. Inspection at regular intervals is essential for
safety.
Inspect the power tool at regular intervals so that
the power tool can be operated safety and
efficiently at all times.
11. Consult an authorized service center if repair or
parts replacement is necessary.
Ensure that the power tool is serviced by authorized
service center only, and that only genuine
replacement parts are used.
12. Keep the power tool in a proper place.
When not in use, the power tool should be kept
in a dry place out of the reach of children. Put
into the body about 2cc oil through the hose joint
to protect the tool from rust.
13. The exploded assembly drawing on this handling
instructions should be used only for authorized
service center.
PRECAUTIONS ON USING NAILER
1. Safe operation through correct usage
This tool was designed for driving nails into wood
and similar materials. Use it for its intended
purpose only.
2. Make sure air pressure is within the rated range
of air pressure.
Please make sure that the air pressure is within
a range of 4.9 bar – 8.3 bar, and that the air which
is used is clean and dry. If the air pressure is
greater than 8.3 bar, the life of the power tool
will be shortened and dangerous conditions could
develop. Tools shall not be connected to pressure
which potentially exceeds 14 bar.
3. Never operate the equipment with high-pressure
gases other than compressed air.
Never use carbon dioxide, oxygen or another gas
from pressurized containers under any
circumstances.
4. Be careful of ignition and explosions.
Since sparks may fly during nailing, it is dangerous
to use this tool near lacquer, paint, benzine, thinner,
gasoline, gas, adhesives and similar inflammable
substances as they may ignite or explode. Under
no circumstances should this tool therefore be
used in the vicinity of such inflammable material.
5. Always wear eye protection (protective goggles).
When operating the power tool, always wear eye
protection, and ensure that surrounding people
wear eye protection too.
The possibility of fragments of the nails that were
not properly hit entering the eye is a threat to
sight. Eye protection can be bought at any
hardware store. Always wear eye protection while
operating this tool. Use either eye protection or
a wide vision mask over prescription glasses.
Employers should always enforce the use of eye
protection equipment.
6. Protect your ears and head.
When engaged in nailing work please wear ear
mufflers and head protection. Also, depending on
condition, ensure that surrounding people also
wear ear mufflers and head protection.
7. Pay attention to those working close to you.
It would be very dangerous if nails that were not
properly driven in should hit other people.
Therefore, always pay attention to the safety of
the people around you when using this tool.
Always make sure that nobody’s body, hands or
feet are close to the nail outlet.
8. Never point the nail outlet towards people.
Always assume the tool contains fasteners.
If the nail outlet is pointed towards people, serious
accidents may be caused if you mistakenly
discharge the tool. When connecting and
disconnecting the hose, during nail loading or
similar operations, be sure the nail outlet is not
pointed towards anyone (including yourself). Even
when no nails are loaded at all, it is dangerous
to discharge the tool while pointing it at someone,
so never attempt to do so. No horseplay. Respect
the tool as a working implement.
9. Before using the power tool, check the push
lever.
Before using the power tool make sure to check
that the push lever and valve operate properly.
Without nails loaded into the power tool, connect
the hose and check the following. If the sound
of operation occurs this indicates a fault, so in

Produkt Specifikationer

Mærke: Hikoki
Kategori: Hæftemaskine
Model: NT65M2

Har du brug for hjælp?

Hvis du har brug for hjælp til Hikoki NT65M2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hæftemaskine Hikoki Manualer

Hikoki

Hikoki NP1835DA Manual

21 Juli 2025
Hikoki

Hikoki NT1865DAA Manual

11 Juli 2025
Hikoki

Hikoki NR 1890DCA Manual

9 Juli 2025
Hikoki

Hikoki NT1865DSA Manual

9 Juli 2025
Hikoki

Hikoki NT65MA4 Manual

25 August 2024
Hikoki

Hikoki NR90AD Manual

25 August 2024
Hikoki

Hikoki NT1865DBSL Manual

25 August 2024
Hikoki

Hikoki NC40G Manual

23 August 2024
Hikoki

Hikoki NV65HMC Manual

23 August 2024
Hikoki

Hikoki NV100H Manual

23 August 2024

Hæftemaskine Manualer

Nyeste Hæftemaskine Manualer

Milwaukee

Milwaukee M18 FUEL FFN Manual

30 Juli 2025
Milwaukee

Milwaukee M18 FDN Manual

22 Juli 2025
Sthor

Sthor 78157 Manual

18 Juli 2025
Craftsman

Craftsman CMCN616 Manual

17 Juli 2025
Milwaukee

Milwaukee M18 FUEL 2744-20 Manual

16 Juli 2025
Milwaukee

Milwaukee 7220-20 Manual

16 Juli 2025
Milwaukee

Milwaukee M18 FUEL 2745-20 Manual

15 Juli 2025
Milwaukee

Milwaukee M18 FUEL 2839-20 Manual

15 Juli 2025
Bosch

Bosch GBA 12V 6.0Ah Professional Manual

10 Juli 2025
Milwaukee

Milwaukee M18 FUEL FRCN45 Manual

9 Juli 2025