Hinkley Lighting Bolla 4660BN Manual

Hinkley Lighting Lys Bolla 4660BN

Læs gratis den danske manual til Hinkley Lighting Bolla 4660BN (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Hinkley Lighting Bolla 4660BN, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
assembly instructions
Family: Bolla Item No. 4660
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
*** The construction of this fixture will be accomplished by first assembling the
main body of the fixture, making all necessary electrical connections, hanging
the fixture from the ceiling, and then installing the glass.
start here
4660
1. To assemble main body, take stem and thread one end into coupler - see (2) (A)
Drawing 3.
Drawing 3 - Fixture Assembly
1
2
3
4
5
7
10
9
A
Drawing 2 - Fixture Mounting
Drawing 1 - Strap Detail
B
(side view)
gull wing
bracket
B
8.10.10
1. Prepare gem strap for mounting by threading two screws provided into (A) (B)
back of gull wing bracket of gem strap - see .(A) Drawing 1
• Be sure the holes into which the screws are threaded match the spacing of holes (D)
in the canopy - see .(E) Drawings 1 and 2
3. Mount gem strap to junction box , using the two 1” screws not provided.(A) (J) (C)
Make electrical connections from supply wire to fixture lead wires. Refer to instruction
sheet and follow all instructions to make all necessary wiring connections.(I.S. 18)
1. Hang the fixture by slipping the holes in the canopy over the screws in(D) (E) (B)
the mounting strap - see .(A) Drawing 2
2. Thread on ball knobs to secure fixture to the ceiling.(F)
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
3
4
5
6
68
031813
1. Prior to installing glass, fixture can be lamped accordingly.
2. (2) (A) To begin glass installation first thread threaded tubing into swivel mount
approximately 3/8”, and then tighten hex nut up against swivel mount to secure (H) (A)
threaded tube - see .(2) Drawing 3
3. (4) Next slide metal washer followed by plastic washer (3) onto threaded tube .(2)
4. While holding them in place, slip glass onto threaded tube .(5) (2)
5. While holding glass in place slip plastic washer followed by flat washer (5) (6) (7)
onto threaded tube , then thread hex nut onto threaded tube and tighten to (2) (8) (2)
secure glass.
6. Slip spider assembly onto end of threaded tube .(9) (2)
7. While holding in place, thread on finial to secure spider assembly . (10) (9)
revised 10.14.15
T24 JA8-2016
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
I.S. 18 wiri roun g n onsng g din i st ctiru
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
w t t siring ins ruc ion
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see .Drawings 1 or 2
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Please refer to the below to complete all grounding instructions
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see . Drawings 2 or 3
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the below to complete all grounding instructions
electrical connections.
gr r sounding inst uction
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (typically copper or green plastic coated) to the fixture mounting strap (E) (1)
with the ground screw - see . (2) Drawing 1
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (typically copper or green plastic coated) under the (E)
head of the ground screw on fixture mounting strap and connect to the (2) (1)
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see .Drawing 2
Post-Mount Fixtures
Connect fixture ground wire (typically copper or green plastic coated) to power (E)
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see .Drawing 3
Drawing 1 - Flush Mount
Drawing 2 - Chain Hung
supply wire
fixture leads
twist-on
connectors
Drawing 3 - Post-Mount
twist-on
connectors
1
A CC
B D
supply wire
fixture leads
A C
B D
1
2
supply wire
fixture leads
A C
B D
twist-on
connectors
E
2
E
E
E
E
I.S. 18
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

Produkt Specifikationer

Mærke: Hinkley Lighting
Kategori: Lys
Model: Bolla 4660BN

Har du brug for hjælp?

Hvis du har brug for hjælp til Hinkley Lighting Bolla 4660BN stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys Hinkley Lighting Manualer

Hinkley Lighting

Hinkley Lighting 6638BK Manual

19 Juli 2025
Hinkley Lighting

Hinkley Lighting Dot 15075SS Manual

4 Juli 2025
Hinkley Lighting

Hinkley Lighting Taper 1553BZ Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting Congress 50122AN Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting Pro-Series 0600SS Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting Manor House 1449 Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting Tiverton 28830DX Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting 992002FBN Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting 55300BZ Manual

21 Juni 2025
Hinkley Lighting

Hinkley Lighting 6610BK Manual

21 Juni 2025

Lys Manualer

Nyeste Lys Manualer

Cotech

Cotech SP-LS3M120GR-01B Manual

1 August 2025
Zhiyun

Zhiyun FIVERAY M20C Manual

1 August 2025
Cotech

Cotech K-NCF-LN10W Manual

1 August 2025
Godox

Godox LA200R Manual

1 August 2025
Cotech

Cotech A60I-047M0-027 Manual

1 August 2025
Cotech

Cotech FIB75600v1-pt Manual

1 August 2025
Godox

Godox LA150R Manual

1 August 2025
Godox

Godox SL300II Manual

1 August 2025
Emos

Emos ZM6155 Manual

1 August 2025
RYOBI

RYOBI RML4 Manual

1 August 2025