Honeywell CT53K1006/E1 Manual

Honeywell Termostat CT53K1006/E1

Læs gratis den danske manual til Honeywell CT53K1006/E1 (16 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Honeywell CT53K1006/E1, eller vil du spørge andre brugere om produktet?

Side 1/16
Owners Manual
English: Page 1
Mode d’emploi
Français : Page 6
Manual de Uso
Español: Página 11
CT50 Series Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2019 Honeywell International Inc.
All rights reserved.
Read and save these instructions
M23786
MERCURY NOTICE
If your old thermostat contains
mercury, contact your local waste
management authority for proper
disposal instructions.
TURN OFF POWER at heating/cooling system (or fuse/circuit-breaker panel).
Remove cover and thermostat, but leave wallplate with wires attached.
Temperature Control Range
45°–95°F (7°–35°C)
35°–85°F (2°–29°C); select models; for garages or other outbuildings.
Is there a sealed tube containing mercury?
If so, see mercury notice below.
Leave wallplate in place.
Old thermostat Cover
Check package contents:
Thermostat
Wall anchors & screws (2 each)
Wire labels
Before you begin, make sure you have:
No. 2 Phillips & small pocket
screwdrivers
Hammer
Level (optional)
Pencil
Drill and bit (3/16” for drywall, 7/32” for
plaster)
Getting started
Remove your old thermostat
Vertical Mount:
CT50 (24 Vac heating systems)
CT51 (24 Vac heating and cooling systems)
CT53 (750 mV or 12Vdc heating systems)
Horizontal Mount:
CT54 (24 Vac heating systems)
CT55 (24 Vac heating and cooling systems)
69-2040EFS-04
CT50 Series • Owner's Manual
69-2040EFS—04 2
M23789
M23787
M23790
M23788
Wrap supplied labels securely around each wire. let wires fall into wall opening!Do not
IGNORE WIRE COLORS: Use only letter
designations to identify wire types.
For CT51/CT55: If your old
thermostat has 7 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
CT50/CT53/CT54
1. Pull wires
through base.
2. Level base if
desired.
3. Mark positions
of both screw
holes.
For CT50/CT53/CT54: If your old
thermostat has 3 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with
the label matching the letter on your old thermostat. (Adhesive labels are supplied in your
thermostat package.)
Remove the old wallplate only all wires are labeled. Be careful not to let loose wires fall after
into the wall opening.
Label wires and remove old wallplate
Mark mounting position
CT51/CT55
CT50/CT53/CT54 CT51/CT55


Produkt Specifikationer

Mærke: Honeywell
Kategori: Termostat
Model: CT53K1006/E1

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell CT53K1006/E1 stil et spørgsmål nedenfor, og andre brugere vil svare dig