Honeywell CT54 Manual

Honeywell Termostat CT54

Læs gratis den danske manual til Honeywell CT54 (8 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Honeywell CT54, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1696EF

CT54 Thermostat

STEP 1. PREPARE FOR

INSTALLATION

The CT54 Thermostat controls 2-wire, 15 Vac to 30 Vac,

gas, oil or electric heating-only systems.

The CT54 Thermostat is not suitable for:

• cooling systems

• heating-cooling systems

• 3-wire electric heating systems

If you are unsure which thermostat model is right for your

system, visit www.honeywell.com/yourhome or call

Honeywell Customer Care at 1-800-468-1502.

1. Check that the following components are included:

• Thermostat

• Two one-inch screws

• Installation Instructions

2. Required tools:

• Slotted screwdriver

• Drill

• Drill bit (1/16 in.)

• Needle nose pliers

• Level

• Pencil

STEP 2. REMOVE OLD

THERMOSTAT

1. Turn power off to the system at the furnace or at

the fuse/circuit breaker panel.

2. If the cover does not easily pull off, remove any

screws that may fasten the cover to the thermostat.

3. Locate the heat anticipator scale and the heat

anticipator lever on the old thermostat (see Fig. 1).

Fig. 1. Heat anticipator on old thermostat (example).

4. Record the number that the heat

anticipator lever points to on the heat

anticipator scale.

NOTE: If you cannot find the heat anticipator setting on

your thermostat, you can use a standard setting

for your type of system when you reach Step 5.

Set Heat Anticipator On New Thermostat.

5. Remove the screw or screws that hold the thermo-

stat to the wall and pull the thermostat away from

the wall.

6. Remove the two wires from the old thermostat and

wrap them around a pencil to keep them from fall-

ing back into the wall (see Fig. 2). If there are more

than two wires connected to your old thermostat,

do not remove the wires. Visit www.honey-

well.com/yourhome or call 1-800-468-1502 for fur-

ther assistance with the installation.

Fig. 2. Pull wires through wall opening.

M21192

OLD THERMOSTAT HEAT

ANTICIPATOR SCALE

HEAT ANTICIPATOR LEVER

TYPI

L LO

TIO

AND

LEVE

WIRES

THROUG

WALL

OPENING

M1964

CT54 THERMOSTAT

69-1696EF 2

MERCURY NOTICE

If this thermostat is replacing a control that

contains mercury in a sealed tube, do not place

the old thermostat in the trash. Contact your local

waste management authority for instructions

regarding recycling and proper disposal of this

control or of an old control containing mercury in

a sealed tube.

STEP 3. CONNECT WIRES TO NEW

THERMOSTAT

IMPORTANT

All wiring must comply with local building codes

and ordinances. If you are unsure about house-

hold wiring procedures, please call your local

heating/cooling contractor.

1. Remove the cover on the new thermostat. To

remove the cover, insert your thumb into the inden-

tation on the bottom and pull the cover away from

the thermostat (see Fig. 3).

2. Loosen the R and W terminal screws on the back

of the new thermostat (see Fig. 4).

3. Remove the two wires from the pencil and attach

one wire to the R terminal and the other wire to the

W terminal (see Fig. 4 and 5).

4. Plug the hole in the wall with insulation to prevent a

warm or cool draft from affecting the operation of

the thermostat.

Fig. 3. Remove cover on new thermostat.

Fig. 4. R and W terminals on new thermostat.

Fig. 5. Wraparound and straight wiring connections.

STEP 4. MOUNT NEW

THERMOSTAT TO WALL

1. Position the thermostat on the wall. Place a level

on top of the thermostat and use a pencil to mark

the two mounting holes on the wall (see Fig. 6).

2. Move the thermostat to the side and drill the

mounting holes in the wall using a 1/16 in. drill bit

at the locations you marked.

3. Position the thermostat over the drilled holes and

loosely insert the mounting screws into the drilled

holes. Check the leveling of the thermostat and

tighten the mounting screws. Do not over tighten.

Fig. 6. Mount new thermostat to wall.

M1964

BOTTOM OF

THERMOSTAT

COVER

M1964

M19648

OR WRAPAROUND

NSERTION STRIP

/16 IN. (11 MM)

FOR STRAIGH

INSERTION

STRIP

5/16 IN. (8 MM

)

.18

.25 .3

LEVEL

DATE CODE

MODEL NO.

M19649

NOTE: MOVE TEMPERATURE

LEVER IF IT BLOCKS

MOUNTING HOLE

MOUNTIN

HOLE

MOUNTING

HOLE

Produkt Specifikationer

Mærke:	Honeywell
Kategori:	Termostat
Model:	CT54

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell CT54 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Honeywell Manualer

Honeywell X2P Manual

1 Juli 2025

Honeywell X1N Manual

29 Juni 2025

Honeywell X2S Manual

29 Juni 2025

Honeywell RTH21B Manual

14 Juni 2025

Honeywell off Manual

15 Januar 2025

Honeywell Round Wireless Modulation - Y87RF1004 Manual

15 Januar 2025

Honeywell Day Night Round T8700A Manual

4 Oktober 2024

Honeywell Round on-off T87G1006 Manual

4 Oktober 2024

Honeywell TH2210DV1006/U Manual

1 Oktober 2024

Honeywell T822L1000/U Manual

29 September 2024

Termostat Manualer

Nyeste Termostat Manualer

Daikin BRC1D528 Manual

11 August 2025

Carrier Infinity SYSTXCCITC01-B Manual

10 August 2025

Hager WXF315 Manual

9 August 2025

Hama 176592 Manual

9 August 2025

Eberle UTE 1002 Manual

7 August 2025

Eberle UTE 1012 Manual

7 August 2025

Eberle SSR-E 6905 Manual

7 August 2025

JUNG CD 500 Manual

7 August 2025

Levoit Aura Sensor LTM-AS041S-WUS Manual

6 August 2025

Perel CTH407 Manual

5 August 2025