Honeywell TL8130A Manual

Honeywell Termostat TL8130A

Læs gratis den danske manual til Honeywell TL8130A (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Honeywell TL8130A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

TL8130A 69-1805 3/5/05 1/2

Honeywell’s TL8130A programmable thermostat can be connected to an

electric heater to control the room temperature.

*Set the switch to Standby to cut power to the heater. This will not affect the time

and temperature settings.

** The thermostat displays the heater duty cycle required to maintain the desired tem-

perature. For example, appears when the heater is activated 40 percent of the

time.

• To remove the control module from the power

base, loosen the captive screw underneath the

thermostat and pull the two components apart as

shown.

• To install the control module onto the power

base, reverse the above procedure.

NOTE: Always keep the thermostat's vents clean and

unobstructed.

Some thermostat configurations can be

modified via the switches on the back of the

control module.

Default (factory) settings are inside the gray cells.

Upon power-up, the thermostat is in manual mode ( ) and displays the

actual temperature.

nPress the Hour and Min buttons to set the time.

oPress the Day button to set the day.

LO: The measured temperature is below 0°C (32°F).

Heating is activated.

HI: The measured temperature is above 50°C (122°F).

When the backlight button is pressed, the display illuminates for 5 seconds.

When either of the buttons is pressed, the display illuminates for 10 sec-

onds.

Setpoint

The thermostat normally displays the actual temperature. To view the set-

point, press one of the buttons once or press the backlight button. The

setpoint will appear for the next 5 seconds.

To change the setpoint, press one of the buttons until the desired temper-

ature is displayed. To scroll faster, hold the button.

Preset buttons

The thermostat has 3 temperature preset buttons:

Comfort preset button

Economy preset button

Vacation preset button

To use a preset temperature, press the appropriate button. The corresponding

icon , or will be displayed.

The following table shows the intended use and the default setting of each of

the preset buttons.

To store a preset temperature:

nSet the desired temperature using the buttons.

oPress and hold the appropriate preset button until the corresponding

icon is displayed.

pPress Mode/Ret to exit.

nn 1.

Display

% of duty cycle 1 to 24% 25 to 49% 50 to 74% 75 to 99% 100%

oo 2.

pp 3.

# Configurations UP DN

SW1 Temperature format a

a. If you change the temperature display format, the preset buttons ( , and )

will return to their default settings.

°F °C

SW2 Early Start b

b. Early Start can be used in Automatic mode only. When this function is enabled, the

thermostat calculates the optimal time to start heating in order to obtain the desired

temperature by the set time. The thermostat re-assesses the start time daily based

on the previous day’s performance.

Disable Enable

SW3 Time format 12-hour 24-hour

On/Standby

switch *

Day and time

settings

Temperature

adjustment

buttons

Program button

Mode selection /

program exit

Temperature display

Mode display

Period display

Temperature

preset buttons

Time and day display

Heating power **

Backlight button

Program

clear button

Preset temperature

icon

Appears when

the setpoint is

displayed

qq 4.

rr 5.

ss 6.

tt 7.

Icon Intended use Default setting New

Comfort

(when at home) 21°C (70°F)

Economy

(when asleep or away from home) 16.5°C (62°F)

Vacation

(during prolonged absence) 10°C (50°F)

TL8130A 69-1805 3/5/05 2/2

The thermostat has 3 operating modes.

Automatic - The temperature is set according to the energy-saving

schedule. To place the thermostat in this mode, press Mode/Ret until is

displayed. The current period setting is also displayed.

Temporary Bypass: If you modify the setpoint (by pressing the ,

or button) when the thermostat is in automatic mode, the new setpoint

will be used until the beginning of the next period.

Manual - The energy-saving schedule is not used. The temperature must

be set manually. To place the thermostat in this mode:

nPress Mode/Ret until is displayed.

oSet the temperature using the , or button.

Vacation - The thermostat is set to the Vacation temperature. Press

to place the thermostat in Vacation mode.

The schedule consists of 4 periods per day which represents a typical week

day. You can program the thermostat to skip the periods that do not apply to

your situation. For example, you can skip periods 2 and 3 for the weekend.

The Comfort ( ) temperature is used in periods 1 and 3 and the Economy

( ) temperature is used in periods 2 and 4. For example, when the period

changes from 1 to 2, the setpoint automatically changes from Comfort setting

( ) to Economy setting ( ).

You can have a different program for each day of the week; i.e., each period

can start at different time for each day of the week. The thermostat has been

programmed with the following schedule.

To modify the schedule:

nPress Pgm to access the programming mode. Period 1 is selected.

oPress Day to select the day to program (hold for 3 seconds to select the

entire week).

pPress Hour and Min to set the start time of the selected period, or press

Clear if you want to skip the period (--:-- is displayed).

qPress Pgm to select another period, or press Day to select another day.

Then repeat step 3.

rPress Mode/Ret to exit the programming mode.

NOTE: If no button is pressed for 60 seconds, the thermostat will automati-

cally exit the programming mode.

Use the following grid to record the new schedule.

Power supply: Refer to the power base installation instructions

Display range: 0°C to 60°C (32°F to 140°F)

Setpoint range: 5°C to 30°C (40°F to 86°F)

Display resolution: 0.5°C (1°F)

Storage: -20°C to 50°C (-4°F to 120°F)

Heating cycle length: 15 minutes

Data backup: In the event of a power failure, most settings are saved. Only

the time must be re-adjusted if the power failure lasts more than 2 hours. The

thermostat will return to the mode that was active prior to the power failure.

Honeywell warrants this product, excluding battery, to be free from defects in the

workmanship or materials, under normal use and service, for a period of five (5)

years from the date of purchase by the consumer. If at any time during the warranty

period the product is determined to be defective or malfunctions, Honeywell shall

repair or replace it (at Honeywell's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from

which you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make

the determination whether the product should be returned to the following

address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N,

Golden Valley, MN 55422, or whether a replacement product can be sent to

you.

This warranty does not cover removal or reinstallation costs. This warranty shall

not apply if it is shown by Honeywell that the defect or malfunction was caused by

damage which occurred while the product was in the possession of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product within the

terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR

DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF

ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS

PRODUCT. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES

ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES,

INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION

OF THIS WARRANTY. Some provinces do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which

vary from province to province.

If you have any questions concerning this warranty, please write Honeywell Cus-

tomer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-

1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell

Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.

If you have any questions about the operation of your thermostat, please go to

www.honeywell.com/yourhome, or call Honeywell Customer Care toll-free

at 1-800-468-1502.

vv 9.

Period Description Associated temperature setting

Wake-up

Away from home

Return home

Sleep

Period Setting MO TU WE TH FR SA SU

6:00 6:00 6:00 6:00 6:00 6:00 6:00

8:00 8:00 8:00 8:00 8:00 --:-- --:--

18:00 18:00 18:00 18:00 18:00 --:-- --:--

22:00 22:00 22:00 22:00 22:00 22:00 22:00

Period Setting MO TU WE TH FR SA SU

ww 10.

;11.

12.

Printed in China

Produkt Specifikationer

Mærke:	Honeywell
Kategori:	Termostat
Model:	TL8130A

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell TL8130A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Honeywell Manualer

Honeywell CT50K1028/E Manual

12 August 2025

Honeywell RET97B5D1002/U Manual

12 August 2025

Honeywell RCHT9510WFW2001/W Manual

12 August 2025

Honeywell CT87K1004/E1 Manual

12 August 2025

Honeywell YCT87N1006 Manual

12 August 2025

Honeywell RTH7500D1049/A Manual

12 August 2025

Honeywell YCT50K1006 Manual

12 August 2025

Honeywell RTH2510B1000/U Manual

12 August 2025

Honeywell RTH221B1039/E1 Manual

12 August 2025

Honeywell RLV3150A1004/E Manual

12 August 2025

Termostat Manualer

Nyeste Termostat Manualer

GE RAK190V Manual

12 August 2025

Daikin BRC1H519W Manual

11 August 2025

Daikin BRC1D528 Manual

11 August 2025

Carrier Infinity SYSTXCCITC01-B Manual

10 August 2025

Hager WXF315 Manual

9 August 2025

Hama 176592 Manual

9 August 2025

Eberle UTE 1002 Manual

7 August 2025

Eberle UTE 1012 Manual

7 August 2025

Eberle SSR-E 6905 Manual

7 August 2025

JUNG CD 500 Manual

7 August 2025