I-PRO WV-S6532LN Manual

I-PRO Overvågningskamera WV-S6532LN

Læs gratis den danske manual til I-PRO WV-S6532LN (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 52 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 26.5 anmeldelser. Har du et spørgsmål om I-PRO WV-S6532LN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

WV-Q122A,

WV-Q185

WV-Q121B

󱷏 󱷐

Step3

Fixing the camera

Step2

Making connections

WV-X6533LN

Preparations

Other items that are needed (not included)

Prepare the required parts for each installation method before starting the installation. The following

are the requirements for the various installation methods.

Installation method

Mounting

screw

Minimum pull-out

strength/ 1pcs.

󱷏When hanging the camera from ceiling

Use the ceiling mount bracket (WV-Q121B

M10 screws/

4pcs.

1411 N {317 lbf}

󱷐When installing the camera on a wall

Use the wall mount bracket (WV-Q122A

, WV-Q185

M10 screws/

4pcs.

823 N {185 lbf}

IMPORTANT:

• The mount bracket (locally procured) should have the configuration that enables

fixation of safety wire from camera.

⇒

Go to Step 1

【

】

Preparations before installation

【

】

Insert an SD memory card as occasion demands.

For the detailed procedures of inserting and removing an SD

memory card, refer to Important Information on the provided

CD-ROM.

① Loosen2SDslotcoverfixingscrews(M4)

usingaPhillipsscrewdriver,andopentheSD

slotcover.

② InsertanSDmemorycardintheSDslot.Push

instraightuntiltheendandconfirmthata

clickingsoundisheard. Take your ﬁ ngers off the

SD memory card and check that its back end does not

protrude over the SD guide rib.

③ Attach the SD slot cover again.

Recommended tightening torque of the SD slot cover

ﬁ xing screws: 1.38 N·m {1.02 lbf·ft}

*1 For details on procedure for attaching mount bracket and

camera, read the operating instructions of each mount bracket.

◆

When using WV-Q121B (option), WV-Q122A (option) or WV-Q185 (option)

⇒

Go to Step 1

【

】

◆

When using the mount bracket (locally procured)

Prepare a mount bracket.

The following ﬁ gure shows an example of the camera mounted on a ceiling with a bracket.

R 1-1/2, 11crest, deep 30 MAX

(taper pipe thread)

RP 1-1/2, 11 crest,

deep 30 MAX

(parallel pipe thread)

60 mm {2-3/8 inches} 25 mm {31/32 inches}

85 mm {3-11/32 inches}

(ﬂ58)

Installation

The installation tasks are explained using 4 steps.

⇨

Step1

Fix the mount bracket

and hang the camera

Step4

Con gure the network

settings

• Remove the camera using the reverse order of the installation procedures.

IMPORTANT:

• After waterproofing the hole for fixing mount

bracket and the port for pulling out the cable

on the installation surface, fix the mount

bracket on the installation surface.

• Adjust the length of cable from camera

attachment port of attachment pipe to cable

end to 180~190 mm {7-3/32 inches~7-15/32

inches}. (If the cable that is pulled out is too

long, storage after wiring becomes difficult.

Adjust the cable length carefully.)

• For the number of fixing screws and the

minimum pull-out strength (per 1 pc.), refer to

the operating instructions of mount bracket

(locally procured).

• Ensure the minimum pull-out strength (per

1 pc.) that has sufficient allowance for total

mass of mount bracket (locally procured),

attachment pipe, and camera etc.

⇒Go to Step 1 【】5 .

Step1 Fix the mount bracket and hang the camera

The following explains an example of installation using mount

bracket (locally procured).

The right figure shows an example of the camera mounted on a ceiling with a

mount bracket (locally procured).

When waterproofing, use waterproof material to fill in gaps and holes

between the attachment pipe and the mount bracket.

【

】

Fix the attachment pipe (accessory) to the mount bracket

(locally procured).

① Fix the attachment pipe to the mount bracket.

② Fill the gap between the mount bracket and attachment pipe with

waterproof material (locally procured) such as silicon clay.

③ Pass the cables from the ceiling through the mount bracket.

【

】

Fix the mount bracket (locally procured) on the installation surface.

Fix a mount bracket to the installation surface on the ceiling by using appropriate bolts,

nuts or the like (locally procured).

180~190 mm

{7-3/32 inches~

7-15/32 inches}

Cable cover ........................................................ 1 pc.

Attachment pipe ................................................. 1 pc.

Waterproof tape .................................................. 1 pc.

RJ45 waterproof connector cover ...................... 1 pc.

RJ45 waterproof connector cap ......................... 1 pc.

Rain wash coating label ...................................... 1 pc.

8P alarm cable ................................................... 1 pc.

24 V AC power supply connector kit ....................1 set

(Power supply connector housing: 1 pc., Contact: 3 pcs.)

Special hexagon screw

.................................. 5 pcs.

(of them, 1 for spare)

Locking washers ............................................... 5 pcs.

(of them, 1 for spare)

About the user manuals

Standard accessories

Installation Guide

(this document) ................................................... 1 pc.

IMPORTANT SAFETY INSTRUCTIONS ............... 1 pc.

CD-ROM*

.......................................................... 1 pc.

Code label*

........................................................ 1 pc.

The CD-ROM contains the several kind of operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. Use caution not to lose this label.

Waterproof tape

*3 The screws are necessary when installing the camera on a separately sold mount bracket.

The following parts are used during installation procedures.

⇨ ⇨

②

180~190 mm

{7-3/32 inches~

7-15/32 inches}

③①

Attachment pipe

(accessory)

Mount bracket

(locally procured)

Waterproof

material

Attachment

pipe

(accessory)

Network Camera

Model No. WV-X6533LN, WV-S6532LN

Installation Guide

CAN ICES-3(A)/NMB-3(A)

'PS$BOBEB

WARNING:

• To prevent injury, this apparatus must be securely

attached to the wall/ceiling in accordance with the

installation instructions.

• All work related to the installation of this product

should be made by qualified service personnel or

system installers.

• The installation shall be carried out in accordance

with all applicable installation rules.

• The connections should comply with local electri-

cal code.

• Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat such as sun-

light, fire or the like.

• This equipment is compliant with Class A of

CISPR 32. In a residential environment this equip-

ment may cause radio interference.

• Operation of this equipment in a residential envi-

ronment could cause radio interference.

CAUTION:

• The network camera is only intended for a con-

nection to an ethernet or PoE+ network without

routing to the outside plant.

• RISK GROUP 2 IR emitted from this product.

Avoid eye exposure. Use appropriate shielding or

eye protection.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household

waste.

For proper treatment, recovery and recycling of old products and used batteries, please take

them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with

the requirement set by the Directive for the chemical involved.

: Caution, infrared radiation

: Direct current symbol

: Alternating current symbol

• Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

• For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate the

camera, refer to the Operating Instructions on the following our support website.

https://i-pro.com/global/en/surveillance/documentation_database

• Before reading this manual, be sure to read the Important Information.

The model number and serial number of this prod-

uct may be found on the surface of the unit.

You should note the model number and serial

number of this unit in the space provided and

retain this book as a permanent record of your

purchase to aid identification in the event of theft.

Model No.

Serial No.

For U.S.A.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equip-

ment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interference

at his own expense.

FCC CAUTION: Changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to oper-

ate the equipment.

For U.S.A.

Supplier’s Declaration of conformity

Trade name : i-PRO

Model No. : WV-X6533LN, WV-S6532LN

Responsible Party :

i-PRO Americas Inc.

8550 Fallbrook Drive, Suite 200 Houston,

Texas 77064

Support Contact : 1-800-513-5417

This device complies with part 15 of FCC Rules

and Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two condi-

tions :

(1)This device may not cause harmful inter-

ference, and (2) this device must accept any inter-

ference received, including interference that may

cause undesired operation.

For U.S.A. and Canada

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

6) Only use attachments/accessories specified by the manufacturer.

7) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

8) Unplug this apparatus during lightning storms or when unused for long periods of time.

9) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Before requesting service, refer to “Troubleshooting” of Important Information in the CD-ROM

and Operating Instructions on our support website. Then, confirm the trouble.

Included Installation Instructions

Open Source Software

󱾀This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

󱾀Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

󱾀Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

󱾀Please note that we shall not respond to any inquiries regarding the contents of the source code.

Product documentation is composed of the following documents.

󱾀Installation Guide (this document): Explains installation, mounting, cable connections, and

network connections. This manual uses the WV-X6533LN as an example in the explanations.

󱾀Important Information (included in the CD-ROM):

Provides basic information about the prod-

uct such as Precautions for installation, Parts and functions, etc..

󱾀Operating Instructions (on our support website): Explains how to perform the settings and

how to operate this camera.

"<Control No.: C****>" used in this document should be used to search for information on our

support website and will guide you to the right information.

Note:

• The external appearance and other parts shown in this manual may differ from the actual

product within the scope that will not interfere with normal use due to improvement of the

product.

• SDXC/SDHC/SD memory card is described as SD memory card.

IMPORTANT:

• Refer to our website

(https://i-pro.com/global/en/surveillance/training_support/

support/technical_information <Control No.: C0120>) for

information on the minimum pull-out strength.

• Prepare four mounting screws (M10) to be mounted on ceiling or

wall separately.

• Select screws according to the material of the location that the

camera will be mounted to. In this case, wood screws and nails

should not be used.

• If the mounting location such as plaster board is too weak to

support the total weight, the area shall be sufficiently reinforced.

SD slot

SD memory card

(with label facing down)

SD slot cover

【

】

Prepare the cables from camera side.

◆

When the only necessary connection to

camera is an Ethernet cable

Do not remove the cable case (2 positions),

use it as it is.

◆

When using 24 V AC, EXT I/O device, or

audio I/O device

Using a Phillips screwdriver detach each cable

case fixed to the top of the camera by 4

screws (M4), and pull out the cable stored

inside. Discard the cable case.

RJ45

Network

cable

Alarm input/output·

Audio input/output

cable

Power supply

terminal

(24 V AC)

Power cable case

Multi cable case

Indication

label

SD slot cover fixing screws

SD guide rib

For U.S. and Canada:

i-PRO Americas Inc.

https://www.i-pro.com/

Ns0319-3042 PGQX2307WA Printed in China

For Europe and other countries:

i-PRO Co., Ltd. Fukuoka, Japan

https://www.i-pro.com/

i-PRO EMEA B.V. UK Branch

1010 Cambourne Business Park,

Cambridgeshire CB23 6DP

Authorised Representative in EU:

i-PRO EMEA B.V.

Laarderhoogtweg 25, 1101 EB

Amsterdam, Netherlands

Produkt Specifikationer

Mærke:	I-PRO
Kategori:	Overvågningskamera
Model:	WV-S6532LN
Kode for international beskyttelse (IP):	IP66
Type:	IP-sikkerhedskamera
Vekselstrømsindgangsspænding:	24 V
Bredde:	249 mm
Dybde:	249 mm
Højde:	465 mm
Vægt:	8200 g
Produktfarve:	Sort, sølv
Kompatible hukommelseskort:	SD, SDHC, SDXC
Formfaktor:	Tårn
Understøttede videotilstande:	720p, 1080p
Opbevaringstemperatur (T-T):	-30 - 60 °C
Relativ luftfugtighed ved drift (H-H):	10 - 100 %
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Understøttede lydformater:	ADPCM, G.726, LC-AAC
Strømforbrug (typisk):	55 W
Driftstemperatur (T-T):	-40 - 60 °C
Maksimal opløsning:	1920 x 1080 pixel
Husmateriale:	Aluminium
Beskyttelsesfunktioner:	Vandal proof, Water resistant
Understøttelse af sprog:	CHI (SIMPL), DEU, ENG, ESP, FRE, ITA, JPN, POR, RUS
Understøttede grafikopløsninger:	320 x 180,640 x 360,1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Forbindelsesteknologi:	Ledningsført
Certificering:	UL (UL60950-1), c-UL (CSA C22.2 No.60950-1), CE, IEC60950-1, FCC (Part15 ClassA), ICES003 ClassA, EN55032 ClassA, EN55024
Netværksstandarder:	IEEE 802.3at
Strømkilde type:	AC, PoE
Monteringstype:	Loft/væg
Indbygget kortlæser:	Ja
Indbygget HDD:	Ingen
Video komprimeringsformater:	H.264, H.265, M-JPEG
Understøttet placering:	Udendørs
Mikrofonindgang:	Ja
Sensortype:	CMOS
Billedstabilisator:	Ja
Samlet antal megapixels:	- MP
Støjreduktion:	Ja
Optisk zoom:	34 x
Digital zoom:	16 x
Maksimal størrelse på hukommelseskort:	256 GB
Hældningsvinkelområde:	-30 - 210 °
Bredt dynamikområde (WDR):	Ja
IK kode:	IK10
Kamerapanorering kontrol:	Ja
Kontrol af kamerahældning:	Ja
Minimumsbelysning:	0.001 Lux
Panoreringsområde:	0 - 360 °
Antal sensorer:	1
Optisk sensorstørrelse:	1/2.8 "
Zoom kapacitet:	Ja
Nærmeste fokuseringsafstand:	3 m
Maksimale blænderåbning tal:	3.7
Nattesyn:	Ja
LED type:	IR
Billedhastighed:	60 fps
Forstærkningskontroltype:	Automatisk
Justering af billedkvalitet:	Lysstyrke
Fortrolighedspolitik maskering:	Ja
Ethernet-grænsefladetype:	Hurtigt ethernet
Bevægelsessensor (video):	Ja
Antal kameraer:	1
Brændviddeområde:	4.25 - 95 mm
Kameraets lukkerhastighed:	1/10000 - 30 sek./side
Mindste blænderåbnimg tal:	1.6
Videostreaming:	Ja
Antal linser:	1
Streaming metode:	Multicast, Unicast
PTZ-kontrol:	Ja
Hældningshastighed:	300 grader i sekundet
Panoreringshastighed:	150 grader i sekundet
Nattesyn, afstand:	100 m
Dynamisk interval:	144 dB
Forudindstillede punkter:	Ja
Strømforbrug (Power over Ethernet (PoE)):	50 W
Region of Interest (ROI) kodning:	Ja
Kompensation for baggrundslys:	Ja
Antal sprog:	9
Objektivets synsvinkel, vandret:	66 °
Alarmindgang/-udgang:	Ja
Objektivets synsvinkel, lodret:	51 °
Highlight Compensation (HLC):	Ja
Auto-sporing:	Ja
Auto patrulje tilstand:	Ja
Forudindstillet hastighed:	300 grader i sekundet
Bitrate kontrol:	Constant Bit Rate (CBR), Variable Bit Rate (VBR)
Auto panoreringstilstand:	Ja