Icom IC-F6062D Manual

Icom Ikke kategoriseret IC-F6062D

Læs gratis den danske manual til Icom IC-F6062D (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Icom IC-F6062D, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
INSTRUCTIONS
VHF dPMR MOBILE TRANSCEIVER
|F5062D
UHF dPMR MOBILE TRANSCEIVER
|F6061D
|F6062D
1-1-32 Kamiminami, Hirano-ku,
Osaka 547-0003, Japan
Nov. 2021
A7217W-1EU-3
Printed in Japan
© 2015–2021 Icom Inc.
Icom, Icom Inc. and the Icom logo are registered
trademarks of Icom Incorporated (Japan) in Japan, the
United States, the United Kingdom, Germany, France,
Spain, Russia, Australia, New Zealand, and/or other
countries.
AMBE+2 is a trademark and property of Digital Voice
Systems Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
IMPORTANT
This instruction sheet includes some functions that are
usable only when they are preset by your dealer. The
transceiver may have other functions and operations that
are not described in this instruction sheet. Ask your dealer
for preset function details.
EXPLICIT DEFINITIONS
WORD DEFINITION
R WARNING!

shock may occur.
CAUTION Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No

shock.
ANTENNA
A key element in the performance of any communication
systems is the antenna. Contact your dealer for
information regarding antennas and how to install them.
FUSE REPLACEMENT
Fuses are installed in the supplied DC power cable. If a
fuse blows, track down the source of the problem, repair it,
and then replace the damaged fuse with a new rated one.
L
Fuse rating: 250 V 10 A
or 20 A (depending on the version)
NOTE:
25 W transceiver: 10 A, 45 W transceivers: 20 A
Fuse rating explanation
Fuse coding: FUSE 250 V 10 A
Fuse voltage rating: 250 Volts
Fuse current rating: 10 Amperes
ABOUT CE AND DOC
Hereby, Icom Inc. declares that the versions
of IC-F5062D and IC-F6062D which have
the “CE” symbol on the product, comply with
the essential requirements of the Radio
Equipment Directive, 2014/53/EU, and the

substances in electrical and electronic
equipment Directive, 2011/65/EU. The full
text of the EU declaration of conformity is
available at the following internet address:
https://www.icomjapan.com/support/
About e-marking: Detailed installation notes for

available.
Please contact your Icom dealer or distributor.
DISPOSAL
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must
be taken to designated collection locations at
the end of their working life. Do not dispose
of these products as unsorted municipal
waste. Dispose of them according to the
laws in your area.
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form.
U.S. Patent Nos.
#8,595,002, #8,359,197, #8,315,860, #8,200,497,
#7,970,606, #6,912,495 B2.
PRECAUTIONS
R WARNING! NEVER connect the transceiver to an AC

shock.
R WARNING! NEVER operate the transceiver during a
lightning storm. It may result in an electric shock, cause

power source and antenna before a storm.
R WARNING! NEVER connect the transceiver to a power
source of more than 16 V DC such as a 24 V battery. This
could damage the transceiver.
R WARNING! NEVER cut the DC power cable between
the DC plug and fuse holder. If an incorrect connection is
made after cutting, the transceiver might be damaged.
R WARNING! NEVER place the transceiver where normal
operation of the vehicle may be hindered or where it could
cause bodily injury.
CAUTION: DO NOT expose the transceiver to rain, snow
or any liquids.
CAUTION: DO NOT
󰀨
and may damage the radio.
CAUTION: DO NOT place or leave the transceiver in
areas with temperatures below –25°C or above +55°C, or
in areas subject to direct sunlight, such as the dashboard.
CAUTION: DO NOT operate the transceiver without
running the vehicle’s engine. The vehicle’s battery will
quickly run out when the transceiver transmits while the
vehicle’s engine is OFF.
CAUTION: DO NOT place or leave the transceiver in
excessively dusty environments.
CAUTION: DO NOT place the transceiver against walls.
Otherwise heat dissipation will be obstructed.
CAUTION: DO NOT use harsh solvents such as

transceiver’s surfaces.
CAUTION: CONFIRM that all connectors and jacks are
dry and clean before attachment. Exposing them to dust or
water will result in serious damage to the transceiver.
NEVER place the transceiver in an insecure place to avoid

BE CAREFUL! The transceiver will become hot when
operating continuously for long periods.
CLEANING
If the transceiver becomes dusty or dirty, wipe it clean with
a soft, dry cloth.
SUPPLIED ACCESSORIES
Microphone
Microphone hanger
and screw set
Function name
stickers*
1
Microphone
hanger cable
Mounting bracket
DC power cable
Bracket bolts
Mounting screws
(M5×12 mm)
Self-tapping screws
(M5×16 mm)
Flat washers
Spring washers
Nuts
NOTE: Some accessories are not supplied, or the shape
󰀨
OPTIONS
• RMK-3  + OPC-609 
Allows you to install the transceiver main unit separately
from the front panel for operating convenience.
• SP-30/SP-35/SP-35L 
Input impedance: 4 ø
SP-35/SP-35L: Rated input 5 W, Max. input 7 W
SP-30: Rated input 20 W, Max. input 30 W
• HM-152/HM-152T/HM-148G/HM-148T 
HM-152: Hand microphone
HM-152T: DTMF microphone
HM-148G: Self grounding heavy duty microphone
HM-148T: Self grounding heavy duty microphone with
10-keypad
The 10-keypad of this microphone can be
used for the DTMF code transmission only.
• SM-26 
• UT-109R/UT-110R 
Non-rolling type (UT-109R)/Rolling type (UT-110R) voice
scrambler unit provides high communication security.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• 

disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom transceivers with any equipment that is
not manufactured or approved by Icom.
See the operating guide for details of the IDAS™ dPMR™
(digital Private Mobile Radio) and the BIIS (Binary
Interchange of Information and Signaling) 1200 system
operations. Ask your dealer for details.
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
SAVE THESE INSTRUCTIONS — These instructions
contain important operating instructions for the
IC-F5062D, IC-F6061D and the IC-F6062D.
Sponges*
2
*
1
Used for labelling the programmable function keys
according to their assinged functions.
*
2
Used for optional unit installation.
Ask your dealer for details.
MOUNTING THE TRANSCEIVER
The universal mounting bracket supplied with your
transceiver allows under or overhead mounting.
• Mount the transceiver securely with the 4 supplied
screws to a thick surface that can support more than 1.5
kg (3.3 lb).
Flat washer
Felt*
Felt*
Spring washer
When using the
self -tapping screws
*The felt pads reduce vibration.
FREQUENCY RANGE AND OUTPUT POWER
• VHF Mobile Transceiver
Model Version
Frequency
Range
Output
Power
IC-F5062D –  25 W

• UHF Mobile Transceiver
Model Version
Frequency
Range
Output
Power
IC-F6061D DPM-23

45 W
IC-F6062D DPM-22 25 W

*Except DPM-23
For European versions
CAUTION: Hot surfaces. DO NOT touch
the transceiver’s surface after continuously
transmitting for long periods of time. The
transceiver’s chassis radiates heat, and it
will become hot to protect the power

may cause a burn.
PANEL DESCRIPTION FUNCTION DISPLAY
REAR PANEL CONNECTION
1
ANTENNA CONNECTOR
Connect to an antenna. Contact your dealer about
antenna selection and placement.
2 EXTERNAL SPEAKER JACK
Connect a 4 ~ 8 Ω external speaker.
3 D-Sub 25-pin
Connects to an external unit.
4
MICROPHONE HANGER
Connect the supplied microphone hanger to the
vehicle’s ground for microphone ON/OFF hook
functions. (See ‘PANEL DESCRIPTION’ for details.)
5 IGNITION LEAD
Connects to an ignition line.
CAUTION: DO NOT
put a pressure on
this lead. Binding to the DC power cable is
recommended.
6
DC POWER RECEPTACLE.
Connects to a 12 V DC battery. Pay attention to
polarities.
R WARNING! NEVER connect to a 24 V battery. This
will damage the transceiver.
D About the LED indicator
• Lights red while transmitting.
• Lights green while receiving a signal, or when the
squelch is open.
D About the Microphone connector
Connect the supplied or optional microphone.
NEVER connect non-specied microphones. The pin
assignments may be di󰀨erent and may damage the
transceiver.
[VOL]
LED indicator Up/Down keys
Power key [ ]
Dealer-assignable keys*
[P0], [P1], [P2], [P3], [P4]
*Ask your dealer for details.
Function display Speaker
Microphone
connector
D MICROPHONE
The supplied or optional microphone has a PTT switch
and a hanger.
• The following functions are available when you put the
microphone ON hook, or take it OFF hook (depending on
the presetting):
- Automatic scan starts when you put it ON hook.
- Scan is paused or cancelled when you take it OFF
hook.
- Automatically selects the Priority A channel when you
take it OFF hook.
- Sets to the ‘Inaudible’ (mute) mode when you put it ON
hook.
-
Sets to the ‘Audible’ (unmute) mode when you take it
OFF hook
.
q SIGNAL STRENGTH ICON
Displays relative receive signal strength level.
Weak Receive Signal level Strong
w LOW POWER ICON
Displayed when low output power is selected.
e AUDIBLE ICON
➥ Displayed when the channel is in the ‘Audible’
(unmute) mode.
➥ Displayed when a matching signal is received.
r COMPANDER ICON
➥ Displayed when the Compander function is
activated.
When the GPS indicator setting is ON*
➥ Displayed when the GPS receiver acquires the GPS
signal from a satellite. In this case, the compander
icon does not show the Compander function’s
status.
*Ask your dealer for details.
t SCRAMBLER ICON
Displayed when the Voice Scrambler function is
activated.
y BELL ICON
Displayed or blinks when a matching signal is
received, according to the presetting.
u CALL CODE MEMORY ICON
Displayed when the call code memory is selected.
i SCROLL ICON
Displayed when an SDM (Short Data Message),
including more than 12 characters, is selected in the
received message log screen by using [BIIS Button] or
[dPMR Button].
†, ‡
o MESSAGE ICON
Displayed when an SDM or Status message is received.
†, ‡
!0 ALPHANUMERIC DISPLAY
➥ Displays an operating channel number, channel
name, User Set mode contents, DTMF code, etc.
➥ Depending on the presetting, characters are displayed
in 1 line or 2 lines on the LCD.
• In the instruction manual, the LCD illustration is
described as having characters displayed in 2 lines.
!1 ACTIVATED KEY ICON
Displayed above the key assigned as [Scan], [Scan Add/
Del(Tag)], [Lock], [Talk Around], [Surveillance] and [BIIS
Button]
†
, while that key is activated.
†
BIIS operation only
‡
dPMR operation only
Icom Inc.
!1
qw erty iuo
!0
D Turning power ON
z Hold down [ ] to turn ON the power.
NOTE: If the transceiver is programmed for a start up
password, input the digit codes as directed by your
dealer. See the operating guide for details.
D Receiving and Transmitting
Receiving:
1. Select a channel.
z Push [CH Up] or [CH Down].
z Push one of the direct channel select keys,
[MR-CH 1] to [MR-CH 4].
2. When receiving a call, rotate [VOL] to adjust the audio
output level to a comfortable listening level.
Transmitting:
Wait until the channel is clear to avoid interference.
1. Take the microphone off the hook.
• While scanning, the scan stops.
2. Wait for the channel to become clear.
• The channel is busy when the LED indicator lights green.
3. While holding down [PTT], speak at a normal voice
level.
4. Release [PTT] to receive.
IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 to 10 cm (2 to 4 inches)
from your mouth, then speak at a normal voice
level.
BASIC OPERATION
D For mobile operation D For base station operation
Antenna
Antenna
To an
AC outlet
DC Power
supply 13.2 V
Red
Red
Black
Black
Optional Speaker
Optional Speaker
Microphone
Microphone
q
q
w
w
e
e
r
r
t
t
y
y
12 V
Battery
NOTE: Use the terminals as shown
below for the cable connections.
Crimp Solder
R WARNING! NEVER
remove the fuse holders
from the DC power cable.
R WARNING! NEVER
remove the fuse holders
from the DC power cable.
1
ANTENNA CONNECTOR
2 EXTERNAL SPEAKER JACK
3 D-Sub 25-pin
4
MICROPHONE HANGER
5 IGNITION LEAD
6
DC POWER RECEPTACLE.
Connects to a 13.2 V DC power supply. Pay attention
to polarities. Make sure the ground terminal of the DC
power supply is grounded.
NOTE: The antenna
connector typr may
di󰀨er, depending on the
transceiver versions.
NOTE: The antenna
connector typr may
di󰀨er, depending on the
transceiver versions.

Produkt Specifikationer

Mærke: Icom
Kategori: Ikke kategoriseret
Model: IC-F6062D

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom IC-F6062D stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Icom Manualer

Icom

Icom IC-F6122D Manual

20 Juni 2025
Icom

Icom IC-PW2 Manual

20 Juni 2025
Icom

Icom IC-F6330D Manual

20 Juni 2025
Icom

Icom IC-F6062D Manual

20 Juni 2025
Icom

Icom ID-5100 Manual

20 Juni 2025
Icom

Icom AH-167 Manual

20 Juni 2025
Icom

Icom IC-F5130D Manual

20 Juni 2025
Icom

Icom IC-A25NE Manual

20 Juni 2025
Icom

Icom IC-F29SR2 Manual

20 Juni 2025
Icom

Icom IC-FR5100 Manual

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hansgrohe

Hansgrohe Metropol 74551000 Manual

20 Juni 2025
SilverCrest

SilverCrest PD-8957UK Manual

20 Juni 2025
OmniMount

OmniMount NC100C Manual

20 Juni 2025
OmniMount

OmniMount QM100 F Manual

20 Juni 2025
USL

USL CMS-2200 Manual

20 Juni 2025
Dahua Technology

Dahua Technology IVS-IP8000-xE-GU2 Manual

20 Juni 2025
OmniMount

OmniMount WM2-S Manual

20 Juni 2025
Microchip

Microchip MPFS460TS Manual

20 Juni 2025
Maginon

Maginon WK-6 HDW Manual

20 Juni 2025
Fiamma

Fiamma Tank 70 Manual

20 Juni 2025