Inovonics EN1215WEOL Manual

Inovonics Deur-/ramme sensor EN1215WEOL

Læs gratis den danske manual til Inovonics EN1215WEOL (2 sider) i kategorien Deur-/ramme sensor. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Inovonics EN1215WEOL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

8/22/19 357-05043-02 Rev A © Inovonics, 2019 - www.inovonics.com

EN1215WEOL Door/Window with Wall

Tamper and EOL

Installation Instructions

1 Overview

The Inovonics EN1215WEOL door/window with wall tamper and

EOL has a built-in magnetic reed switch on the side, with a

magnet that supports a 5/8" inch gap. The magnetic reed switch

can be used with both ferrous and non-ferrous material. A 2.2K

ohm end of line resistor is included with the EN1215WEOL, and

is required for operation.

The EN1215WEOL includes a back tamper switch. The tamper

condition must be defined within the control panel as a trouble

condition when the system is disarmed, and as an alarm

condition when the system is armed.

The door/window with wall tamper and EOL is available in North

America, Australia and New Zealand; the radio frequency band

has been configured for the appropriate geographic area at the

factory.

Note: For UL installations, refer to the EN4216MR Installation

and Operation Manual, the EN4232MR Installation and

Operation Manual, or the EN7290 EchoStream Receiver/

Interface for Honeywell VISTA Panels Installation Instructions.

The switch contact must also be located in the same room as the

EN1215WEOL, and the EN1215WEOL must be installed in

accordance with UL 681 and ULc S302.

Note: The cable length from the switch contact must not to

exceed 10 feet.

Caution: The EN1215WEOL contains both a wired input and an

input activated by a reed switch and magnet. The reed switch

and magnet must be used unless the application specifically

supports both inputs as separate devices. Use of the wired input

is optional.

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics

Wireless technical services:

• E-mail: support@inovonics.com.

• Phone: (800) 782-2709.

1.2 EN1215WEOL Internal Components

Figure 1 Door/window with wall tamper and EOL internal

components

1.3 What’s In The Carton

• Two wall mount screws.

• Two wall mount anchors.

• Two selection jumpers.

• One 3.0V lithium battery.

• One housing closure screw.

• One magnet.

• One 2.2K ohm end of line resistor.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be installed and maintained

by professional security technicians.

• Products are intended for indoor use.

• Manually test all products weekly.

2.2 Battery Installation

1. Use your thumb to press the housing release tab on the

bottom of the transmitter; separate the housing.

2. Install the battery.

3. Press the reset button to initialize the transmitter.

4. Test the transmitter and ensure appropriate response.

2.3 Select Input Type and Wire Resistor

The N/O-N/C selection pins allow the choice of a normally open

or normally closed state for the contact circuit wired to the input

terminal.

The transmitter is shipped set for normally open, with a selection

jumper on the N/O selections pins.

Set for normally open operation:

1. Place a selection jumper on the selection pins to select

normally open.

2. Use 22 AWG wire to wire the 2.2K ohm resistor in parallel

with the N/0 contact per Figure 2. The distance from the

external contact to the EN1215WEOL must not exceed 10

feet (3 meters).

3. Press the reset button to complete configuration.

Figure 2 Wired for N/O operation

Set for normally closed operation:

1. Remove the selection jumper from the selection pins.

2. Use 22 AWG wire to wire the 2.2K ohm resistor in series with

the N/C contact per Figure 3. The distance from the external

contact to the EN1215WEOL must not exceed 10 feet (3

meters).

3. Press the reset button.

Figure 3 Wired for N/C operation

2.4 Register the EN1215WEOL

Transmitters must be registered with the system in order to be

monitored and supervised. When supervised, the transmitter will

send a check-in message to the receiver every three minutes.

Each transmitter has a unique factory-programmed identification

number.

Refer to the system receiver’s documentation for details on

registering the transmitter.

1. When prompted by the receiver to reset transmitter, press

the reset button.

2. Replace the cover.

3. Test the transmitter and ensure appropriate response.

For product and installation videos visit us at

www.inovonics.com/videos or use the QR

code below.

A Combined housing/wall tamper

switch

B N/O - N/C jumper

C Input terminal D Reset button

E Wall-mount screw holes F Housing closure screw hole

G Reed switch

Produkt Specifikationer

Mærke:	Inovonics
Kategori:	Deur-/ramme sensor
Model:	EN1215WEOL
Bredde:	46 mm
Dybde:	23 mm
Højde:	104 mm
Vægt:	85 g
Velegnet til:	Dør/vindue
Produktfarve:	Hvid
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Driftstemperatur (T-T):	0 - 60 °C
Forbindelsesteknologi:	Trådløs
Batteritype:	CR123A
Bæredygtighedscertifikater:	Federal Communications Commission (FCC), RoHS
Grænseflade:	WLAN
Batteriets levetid:	60 måned(er)
Driftsfrekvens:	902 - 928 MHz
Antal produkter inkluderet:	1 stk
Transmissionsafstand:	3 m