Optex OA-4500 Manual

Optex Deur-/ramme sensor OA-4500

Læs gratis den danske manual til Optex OA-4500 (2 sider) i kategorien Deur-/ramme sensor. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Optex OA-4500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OA-4500S(E)

a. Affix the mounting template at the

desired mounting position.

b. Drill two mounting holes ø3.4 mm (ø1/8")

on the header.

c. To pass the cable through the header,

drill a wiring hole of ø8 mm (ø5/16").

Knockout

ENGLISH

5918983 DEC 2022

Manufacturer's statement

Read this operation manual carefully before use to ensure proper operation of this product.

Failure to read this operation manual may cause improper operation and may result in serious injury or death of a person.

The meanings of the symbols are as follows.

1. This product is a non-contact switch intended for header mount to use on industrial doors.

Do not use for any other applications.

2. When setting the sensor's detection area, make sure that there is no traffic around the installation site.

3. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment

connected to the product.

4. Only use the product as specified in the operation manual provided.

5. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country

in which the product is installed.

6. Before leaving the installation site make sure that the product is operating properly and instruct the

building owner/operator on proper operation of the door and the product.

7. The product settings can only be changed by an installer or service engineer.

When changed, the changed settings and the date shall be registered in the maintenance logbook

accompanying the door.

NOTE

Failure to follow the instructions that accompany this indication and improper handling

may result in serious injury or death.

WARNING

Failure to follow the instructions that accompany this indication and improper handling

may result in injury and/or damage to property.

CAUTION

Pay special attention to sections with this symbol.

NOTE

Specifications

Model

Cover color

Mounting height

Detection area

Detection method

Depth angle adjustment

Power supply

Power consumption

Operation indicator

Output hold time

Response time

Operating temperature

Operating humidity

: OA-4500S(E)

: Black

: 2.5 to 4.5 m (8'2" to 14'9")

: See Detection area

: Active infrared reflection

: 1st to 3rd rows : -6 to +6°

4th and 5th rows : +26 to +44°

: 12 to 24 VAC ±10 % (50/60 Hz)

12 to 30 VDC ±10 %

: < 2.5 W (< 4 VA at AC)

: See Operation indicator table

: Approx. 500 ms

: < 300 ms

: -20 to +55°C (-4 to 131°F)

: < 80 % (Non-condensing)

Activation output

Safety output

IP rate

Weight

Accessories

: When 3rd, 4th or 5th row detects.

N.C./N.O. selectable

50 V 0.3 A Max. (Resistance load)

: When 1st or 2nd row detects.

N.C./N.O. selectable

50 V 0.3 A Max. (Resistance load)

: IP54

: 320 g (11.2 oz)

: 1 Operation manual

2 Mounting screws

1 Mounting template

1 Area adjustment tool

1 Cable 4.0 m (13'2")

The specifications herein are subject to change without prior notice due to improvements.

NOTE

Operation indicator table

Status Operation indicator color

Stand-by Green

Replacement signal Twice Green blinking

Signal saturation Slow Green blinking

2nd to 5th row detection Orange

1st row detection Red

(1) Connector

(2) Mounting holes

Dimensions and part names

[mm(inch)]

267(10 1/2")

36(1 7/16")

125(4 15/16")

43(1 11/16")

7(1/4")

63(2 1/2")

45(1 3/4")

(9)

(5) (5)(4) (6) (7)(3)

(2)

(1)

(3) Operation indicator

(4) Depth angle adjustment screw

Do not wash, disassemble,

rebuild or repair the sensor,

otherwise it may cause electric

shock or breakdown of the

equipment.

Danger of electric shock

WARNING

The following conditions may cause issues with the sensor operation.

Fog,

Exhaust Vibration Objects ReflectionWet

Charts show the values in the following depth angle adjustment settings ;

1st to 3rd rows : +6°

4th and 5th rows : +44°

Detection area

: Emitting spots

: Detection area

: Emitting spots

(Can be eliminated)

1st row

2nd row

3rd row

4th row

5th row

The actual detection area may become smaller depending on the ambient light, the color/material of

the object or the floor as well as the entry speed of the object.

The sensor may not be activated when the entering speed of the object or a person is slower than

50 mm/s or faster than 1500 mm/s.

NOTE

[mm(feet,inch)]

1,850 (6'1")

3,000 (9'10")

200 (8")

580 (1'11")

1,100 (3'7")

2,600 (8'6")

1,810 (5'11")

3,790 (12'5")

300 (12")

4,000 (13'2")

260 (10")

760 (2'6")

1,480 (4'11")

2,460 (8'1")

3,460 (11'4")

4,500 (14'9")

290 (11")

850 (2'9")

1,660 (5'5")

2,760 (9'1")

3,890 (12'9")

2,400 (7'11")

5,050 (16'7")

2,700 (8'10")

5,680 (18'8")

400 (1'4") 450 (1'6")

3,500 (11'6")

230 (9")

670 (2'2")

1,300 (4'3")

2,160 (7'1")

3,030 (9'11")

2,110 (6'11")

4,420 (14'6")

350 (1'2")

1,540 (5'1")

2,500 (8'2")

160 (6")

480 (1'7")

930 (3'6")

2,170 (7'1")

1,510 (4'11")

3,150 (10'4")

250 (10")

Mounting

height

(7) Detection window

(8) Area adjustment tool

(5) Width adjustment screws

(6) Dipswitches

Installation

1. Mounting

Make sure to connect the cable correctly to the door controller before turning the power ON.

When turning the power ON or after adjusting the settings, do not enter the detection area for more than

10 s in order to enable the presence detection.

a. Plug the connector.

b. Supply power to the sensor. Adjust the detection area and set the dipswitches.

(See )Adjustments 3. Dipswitch settings

3. Turn ON the power

NOTE

Do not use the sensor without the cover. When using the

cable knockout, install the sensor indoors or use the rain

cover (Separately available) otherwise electric shock or

breakdown of the sensor may occur.

Place the housing cover.

If wiring is to be exposed,

break the knockout.

4. Mounting the housing cover

2. Wiring

Wire the cable to the door controller.

[mm(inch)]

Mounting holes

ø3.4 mm (ø1/8")

Wiring hole

ø8 mm (ø5/16")

25(1")

The lower

edge of the

header

50(1 15/16")

125(4 15/16")

36(1 7/16")

Activation output

Safety output

Grey

Yellow

Green

Power supply

12 to 24 VAC (50/60 Hz) / 12 to 30 VDC

See DIP 13 to 15 comment

in " ".3. Dipswitch settings

Before starting the procedure,

make sure that the power is turned

OFF. When passing the cable

through the hole, do not tear the

shield otherwise it may cause

electric shock or breakdown of the

sensor.

Danger of electric shock

WARNING

Danger of electric shock

WARNING

Adjustments

1st to 3rd rows

Use the area adjustment tool as shown above to(A)

change the area depth angle for the 1st to 3rd rows.

a. Independent adjustment

Depth angle adjustment screw for the 1st to 3rd rows.

Shallow

Deep

Red

Make sure that the detection area

does not overlap with the door/header,

and there is no highly reflecting object

near the detection area otherwise

ghosting/signal saturation may occur.

Area adjustment tool

1. Area depth angle adjustment

NOTE

Depth angle

adjustment

screw

01.0

(3'3")

1.0

(3'3")

2.0

(6'7")

01.0

(3'3")

2.0

(6'7")

3.0

(9'10")

[mm(feet,inch)]

ShallowDeep

2.0

(6'7")

3.0

(9'10")

4.0

(13'2")

4.5

(14'9")

4th and 5th rows

Use the area adjustment tool as shown(B)

above to change the area depth angle for

the 4th and 5th rows.

Depth angle adjustment screw for the 4th

and 5th rows.

Shallow Deep

Blue

01.0

(3'3")

1.0

(3'3")

2.0

(6'7")

[mm(feet,inch)]

ShallowDeep

2.0

(6'7")

3.0

(9'10")

4.0

(13'2")

4.5

(14'9")

01.0

(3'3")

2.0

(6'7")

3.0

(9'10")

4.0

(13'2")

Shallow

Deep

For the simultaneous adjustment of the

1st to 5th rows, use the adjustment tool .(C)

b. Simultaneous adjustment

ShallowDeep

01.0

(3'3")

1.0

(3'3")

2.0

(6'7")

01.0

(3'3")

2.0

(6'7")

3.0

(9'10")

4.0

(13'2")

2.0

(6'7")

3.0

(9'10")

4.0

(13'2")

4.5

(14'9")

[mm(feet,inch)]

Deep

Shallow

Motion/presence

detection

Mounting

surface

Produkt Specifikationer

Mærke:	Optex
Kategori:	Deur-/ramme sensor
Model:	OA-4500

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex OA-4500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Deur-/ramme sensor Optex Manualer

Optex OA-4500 Manual

30 December 2025

Optex OA-Edge T Manual

5 December 2024

Optex TX/RX-TX Manual

3 September 2024

Optex SW-2 Manual

6 August 2024

Optex VVS-1 Manual

23 Juli 2024

Deur-/ramme sensor Manualer

Nyeste Deur-/ramme sensor Manualer

ORNO OR-SH-17600 Manual

6 September 2024

ORNO OR-SH-17601 Manual

6 September 2024

Emos THS916A Manual

4 September 2024

Emos GS827 Manual

4 September 2024

Emos GS869 Manual

4 September 2024

Avidsen HomeSensor Window Manual

4 September 2024

Kanlux ROLF JQ-L Manual

4 September 2024

Kanlux SENTO Manual

4 September 2024

Kanlux MARID JQ-L Manual

4 September 2024

Gewiss GW90882 Manual

29 August 2024