IPEGA PG-XBX026A Manual

IPEGA Konsol PG-XBX026A

Læs gratis den danske manual til IPEGA PG-XBX026A (1 sider) i kategorien Konsol. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 2 anmeldelser. Har du et spørgsmål om IPEGA PG-XBX026A, eller vil du spørge andre brugere om produktet?

Side 1/1
PWM COOLING FAN
Instruction Manual (PG-XBX026A)
1. Working Voltage: DC 5V
2. Working Current: Fan ≤ 500 mA
3. Applicable platform: XBX console
Headphone holder
Function illustration:
Electrical parameters:
Intelligent Temperature
Control Indicator
RGB Lighting on/off
USB extension port
Cooling Fan on/off
Power cable
1. This product is suitable for cooling the XBX console
2. Temperature detection functionality and can intelligently adjust the cooling fan speed based on
the temperature changes of the console in automatic mode. The cooling fan can also be
manually adjusted to operate at three different speeds using the fan switch.
3. Headphone holder for convenient storage of headphones.
4. With RGB light effect, equipped with a light control switch that can toggle the fan's colorful
lighting effects on and off.
1. Align the fan with the holes on the top of the XBX console and insert it. Then insert the
headphone hook into the two groove slots on the fan, as shown in the figure above (Figure 1).
2. Plug the USB power cable of the fan into the USB port on the XBX console, as shown in the
figure above (Figure 2).
3. Turn on the XBX console, and the four central LED lights on the top fan will light up, creating a
colorful background lighting effect. After 8 seconds, it will automatically enter the default
intelligent temperature control mode, indicated by a steady green light for AUTO.
4. The "Fan Speed Switch" button can control the fan between different modes: intelligent
temperature control mode (AUTO), 1st gear (1300±10% RPM), 2nd gear (1500±10% RPM),
3rd gear (1800±10% RPM), and Off. It also has a fan speed memory function. Press and hold
the button for 3 seconds to turn off the fan, and press it again to restore the fan speed to the
previous setting.
5. When the fan is in "Intelligent Temperature Control Mode" (AUTO), the fan speed depends on
the temperature detected by the temperature sensor inside the fan that is in contact with the
console. The higher the temperature, the faster the fan speed (up to a maximum of 1800±10%
RPM). When entering the "Intelligent Temperature Control Mode," the fan will rotate for 5
seconds regardless of the temperature, and then it will automatically adjust the fan speed
based on the temperature: below 38 degrees Celsius, the fan will not rotate; around 38
degrees Celsius: 1300±10% RPM; around 40 degrees Celsius: 1500±10% RPM; above 42
degrees Celsius: 1800±10% RPM.
Fan component x 1 Headphone holder x 1 Manual x 1
Figure 1 Figure 2
1. Please do not store this product in wet or high-temperature areas.
2. Don’t knap, beat, drub, pierce, or try to decompose this product, to avoid unnecessary damage
to the product.
3. Non professional personnel should not disassemble the product, otherwise it will not be
covered in the after-sales warranty service.
4. This product contains electronic components such as capacitors and should not be casually
discarded. Please dispose of it properly by giving it to qualified recycling facilities.
5. In the event that some products cannot be connected or operated due to uncontrollable factors,
our company accepts no responsibility. Our company reserves the right to make the final
interpretation in such cases.
6. This product does not have short circuit protection, overvoltage protection, or overcurrent
protection. Please do not use it to charge batteries or controllers of other models.
6. The USB expansion port on the top fan supports USB 2.0 data transmission and provides a
current output of 500mA, which can be used for charging the XBX controller while playing.
7. This product is equipped with a light control switch that can toggle the fan's colorful lighting
effects on and off.
XBX
产品明书( )PG-XBX026A
1.工作电压DC 5V
2.工作电流:风扇≤500mA
3.用平台XBX主机
机挂
扇档位指示灯
恒温指示灯
灯效开/关
扩展USB接口
扇档位开/关
电源接线
1. 本产品可供XBX主机散热产品设计巧妙美贴合XBX主机。
2. 本产品有3档风速可控制动或手动控制转速,具备温度检测功能,可根据主机温度
变化动智能调整散热转速
3. 备一个机挂件方便机收纳。
4. 带有RGB灯效灯光控制开关可切换炫彩灯光的开与关。
1. 将扇对准XBX主机上的孔位插入然后将机挂插在扇上的两个凹槽孔位如上图1
2. 将扇的USB电源接线插入到XBX主机USB接口如上图2。
3. 开启XBX主机,顶置风扇中的4个幻彩LED灯会亮起,使扇发出幻彩景灯效8s后默认
入智温控模式对应的AUTO灯光常亮绿
4. “扇档位切换”可控制扇在智温控模式AUTO、1档1300±10%转)
2档1500±10%转)、3档1800±10%转)、停、五种状态之依次切换且具有
档位忆功能,长按3s关闭风再按一下默认为上一次的扇档位。
5. 当扇处于“智温控模式”时,风转速扇伸入主机的温度感应属头的温度值
当温度越高,风转速越1800±10%转); 刚入“智温控模式”时温度
多少,风扇会自转5秒然后根据温度感应属头的温度动智能调整工作状态温度<38度
时不转,温度38度左右1300±10%转,温度40度左右1500±10%转,温度>42度
1800±10%
6. 顶置风扇USB扩展口具备USB2.0数据传及500毫安的电流用于XBX手柄玩。
7. 本产品备灯光控制开关可切换扇炫彩灯光的开与关。
扇x1 机挂x1 明书x1
图1 图2
1. 把本产品在潮湿或温地方存储。
2. 敲击、摔打、刺穿、或图去分本产品以免对产品成不必的损害。
3. ,专业人员拆卸本产品 否则不在售后保修服务内。
4. 产品内有电容等电子材料不可便丢弃,须集中给有资质的回收机构。
5. 因不可抗拒的因素分产品无法接操作我公司不任何对此我公司保留最终解释权。
6. 本产品无短保护压保护流保护,请勿用于其他型号充电电池或手柄充电。
Usage instructions:
Note:
Product list:
Usage instructions:


Produkt Specifikationer

Mærke: IPEGA
Kategori: Konsol
Model: PG-XBX026A

Har du brug for hjælp?

Hvis du har brug for hjælp til IPEGA PG-XBX026A stil et spørgsmål nedenfor, og andre brugere vil svare dig




Konsol IPEGA Manualer

IPEGA

IPEGA PG-XBX016 Manual

13 Oktober 2025
IPEGA

IPEGA PG-XBX003 Manual

13 Oktober 2025
IPEGA

IPEGA PG-XB007 Manual

13 Oktober 2025
IPEGA

IPEGA PG-XBX026A Manual

13 Oktober 2025
IPEGA

IPEGA PG-XBX025SD Manual

12 Oktober 2025
IPEGA

IPEGA PG-XBX028S Manual

12 Oktober 2025
IPEGA

IPEGA PG-XBX025S Manual

12 Oktober 2025
IPEGA

IPEGA PG-XBX013 Manual

12 Oktober 2025
IPEGA

IPEGA PG-XBX012 Manual

14 Juli 2025
IPEGA

IPEGA PG-X010 Manual

10 Juli 2025

Konsol Manualer

Nyeste Konsol Manualer