Jablotron CA-1202 - mode 2 Manual

Jablotron Bilalarm CA-1202 - mode 2

Læs gratis den danske manual til Jablotron CA-1202 - mode 2 (2 sider) i kategorien Bilalarm. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Jablotron CA-1202 - mode 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CA-1202 User manual – Mode 2 - 4 / 4 – MHF53400

10. Car battery low voltage reporting

The built-in voltage drop detector can trigger an alarm if an electrical device in

the car is turned on while the car is armed. Also the car alarm checks the voltage

of the car battery. If the voltage is too low (10V) it will notify users via an SMS

message. The car alarm can be backed up by a BB-01 battery. Thus, the car alarm

can send SMS messages (but not work) even when the car battery is

disconnected. The manufacturer recommends regular BB-01 checking once a

year. The battery should be replaced every two years.

11. Limited number of alarms

If any sensor (input) repeatedly triggers alarms then this particular input will be

bypassed automatically after the third alarm (it will remain bypassed until the car

alarm is disarmed).

12. Remote service

When it is necessary to change the basic settings of the alarm like phone numbers

etc you do not need to contact the installer. Instead it is possible to change settings

remotely.

13. Central monitoring station communication

The car alarm allows central monitoring via GPRS data protocol. Please ask your

supplier for details.

14. Roaming

If you travel abroad and your SIM card supports roaming, the car alarm will

work there too (the functions LOCATOR and CREDIT might be not available).

15. LED indicator signals

The LED indicator is used to show

the status of the alarm. Warning! If

the LED indicator starts flashing

fast after the ignition is switched

off, it will not be able to send any

messages nor call in the case of

an alarm.

LED state Meaning

OFF Disarmed

permanently ON Connecting to a GSM network

or a phone call

Regular slow flashing Armed

Interrupted light Car was stopped

(immobilization)

Flashing fast GSM network is not available

Your installer’s contact details:

CA-1202 User manual – Mode 2 - 1 / 4 – MHF53400

The “Athos” CA-1202 GSM car alarm

MODE 2

Thank you very much for buying our CA-1202 car alarm. Now you will always be able to

find where you left your car. Jablotron Ltd.

1. Remote control arming and disarming

The alarm will be armed when the car is locked remotely by the

original remote control and disarmed when the car is unlocked

remotely. If the car is unlocked by key then the alarm will be

triggered. To stop the alarm it is necessary to unlock remotely by the

original remote control. The RC-40 remote control can be used for

remotely operating the gate, garage door etc. Please ask your

installer for detailed information.

2. Acoustic signals The car alarm informs you about its status

by siren chirps. The chirps for arming (1x),

disarming (2x) and arming with the

triggered input (4x) are optional. Warning!

If the GSM network is not available

while the car alarm is being armed it

will not be able to send any messages

nor call in the case of an alarm.

3. Alarm

When an alarm is triggered (the car alarm is armed and an input is triggered), the

siren will sound for 30 sec’s., warning SMS messages will be sent to all phones

(TEL1 to TEL4) and these phones will also be called with a siren sound1. The alarm

can be terminated by unlocking the car remotely by the original remote control or by

SMS instruction. Your mobile will be sent a message stating that the alarm condition

has ended. If the alarm is triggered accidentally (e.g. by unlocking the door with a

key) then in some cases it is necessary to lock the door first and then

unlock by the original remote control to terminate the alarm.

4. Remote control by SMS instructions

SMS instructions sent from an authorized phone (TEL1 to TEL4) can

operate the alarm remotely. Factory default instruction texts are

shown in the following table. If an SMS is sent from an unauthorized

phone a valid user code must be entered before the instruction (e.g.

USER IMO).

1 If it is activated, then in the case of an alarm all calls are automatically answered

(it is possible to listen and speak to the car remotely).

Chirps Meaning

1x Arming

2x Disarming

3x Disarming after the alarm

4x Arming with the triggered input

6x GSM network is not available

Produkt Specifikationer

Mærke:	Jablotron
Kategori:	Bilalarm
Model:	CA-1202 - mode 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Jablotron CA-1202 - mode 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilalarm Jablotron Manualer

Jablotron CA-321 Accent Manual

22 August 2024

Jablotron CA-1202 - mode 2 Manual

20 August 2024

Jablotron CU-07 Manual

13 August 2024

Jablotron CA-02 Manual

6 August 2024

Jablotron CA-1803BT Athos Manual

3 August 2024

Jablotron BB-02 Manual

2 August 2024

Jablotron CA-340 Nestor Manual

31 Juli 2024

Bilalarm Manualer

Nyeste Bilalarm Manualer

Viper 3308V Manual

28 November 2025

Viper 5308V Manual

9 September 2025

Omega IM01-GMDL6X Manual

18 August 2025

17 Juli 2025

10 Juli 2025

6 Juli 2025

9 April 2025

23 September 2024

20 September 2024

15 September 2024