Viper 3108V Manual

Viper Bilalarm 3108V

Læs gratis den danske manual til Viper 3108V (52 sider) i kategorien Bilalarm. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Viper 3108V, eller vil du spørge andre brugere om produktet?

Side 1/52
Quick Reference Install Guide
3108V Security System
Wiring Connections
Primary Harness, White 12-pin connector
1 RED/WHITE (-) 200mA TRUNK / AUX 1 OUTPUT (Channel 2)
2
RED (+)12V CONSTANT - 15A FUSED (Main power input)
3
BROWN ˜+° SIREN/HORN OUTPUT
4
YELLOW ˜+° IGNITION INPUT ˜See Pre-Wired Starter Kill Relay)
5
BLACK ˜˛° CHASSIS GROUND
6
VIOLET ˜+° DOOR TRIGGER INPUT
7
BLUE ˜˛° INSTANT TRIGGER INPUT
8
GREEN ˜˛° DOOR TRIGGER INPUT
9
BLACK/WHITE
(-) DOME LIGHT OUTPUT
10
WHITE/BLUE (-) 200mA AUX 2 OUTPUT (Channel 3)
11
WHITE (-)/(+) SELECTABLE PARKING LIGHT OUTPUT - 10A FUSED
12
ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
Parking Light
Polarity Jumper (-/+)
Sensor Port
Shock Sensor Adjustment
Clockwise = More Sensitive
Counterclockwise = Less Sensitive
Door Lock, 3-pin connector
1
BLUE
200mA ˜˛° UNLOCK OUTPUT / ˜+° LOCK OUTPUT
2
EMPTY NOT USED
3
GREEN
200mA ˜˛° LOCK OUTPUT / ˜+° UNLOCK OUTPUT
Pre-Wired Starter Kill Relay
86 YELLOW ˜+° IGNITION INPUT
30 GREEN
STARTER ISOLATION - KEY SIDE
87a
BLACK
STARTER ISOLATION - CAR SIDE
D2D Port
(For external interface module)
SMARTSTART PRO / DirectLoader
Control Center
Button
LED
Important: NEVER connect low current outputs directly to a motor or high
current circuit WITHOUT a relay.
Basic Remote Functions
Button Function
ARM
DISARM
PANIC
AUX
TRUNK / AUX
Advanced Remote Functions
Button
AUX 2
(PRESS Together)
AUX 2 - VALIDITY
(HOLD Together)
AUX
Then
SILENT DISARM
+
Press Function Hold Function
SILENT ARM
AUX
Then
© 2024 DIRECTED by VOXX. All Rights Reserved.
Programming System Features
Feature Menus
System Features dictate how the unit operates. It is possible to access and
change most of the feature settings using the Control Center button.
1.
Open a door.
2.
Turn the ignition ON, then OFF.
3.
Within 5 seconds, press and hold the Control Center button. The number of
siren chirps indicates the menu number. One chirp indicates Menu 1,
(continue holding for Menu 2) Two chirps indicates Menu 2.
4.
When the desired menu chirps are heard, release the Control Center button.
5.
Press and release the Control Center button the number of times
corresponding to the feature you wish to change. Then press and hold one
more time to select the feature. Do not release the Control Center button.
6.
While holding the Control Center button, you can program the feature using
the remote control:
To change options press;
LOCK
for Opt 1 and
UNLOCK
to cycle through Opt 2+.
Once a feature is programmed:
Other features can be programmed within the same menu.
Another menu can be selected.
The Learn Routine can be exited if programming is complete.
To access another feature in the same menu:
1. Press and release the Control Center button the number of times necessary to
advance from the feature you just programmed to the next one you want to
program.
2. Then press the Control Center button once more and hold it.
To select another menu:
1. Press and hold the Control Center button.
2. After three seconds, the unit advances to the next menu and the siren
chirps, indicating which menu has been accessed.
Programming routine exits if any of the following occurs:
The open door is closed
The ignition is turned ON
There is no activity for 15 seconds
The Control Center button is pressed too many times
Remote Pairing (4-Button Auto Learn)
The system comes with two remote controls that have been paired to the control
module. The control module can store up to four dierent remote control codes in
memory. Follow the procedure below to pair additional or replacement remotes.
For alternate pairing congurations and channel options, see ‘Remote control
(transmitter) configurations’ in the full installation guide.
1.
Open a door.
2.
Turn the ignition ON.
3.
Press and release the Control Center button 7 times and then press and
hold the Control Center button once more. The siren chirps and the LED
blinks 7 times indicating the 4-Button Auto Learn channel is accessed.
Do not release Control Center button.
4.
While holding the Control Center button, press the LOCK button on the
remote control you want to pair. The siren chirps indicating successful
pairing.
Programming routine exits if any of the following occurs:
The open door is closed
The ignition is turned OFF
There is no activity for 15 seconds
The Control button is pressed too many times
Default settings are in bold type.
Menu 1: Basic Features
Feature
#
Option 1 setting Option 2+ setting
1-1 Active arming
Passive arming
1-2 Chirps: ON Chirps: OFF
1-3
Ignition controlled door locks:
Ignition controlled door locks:
ON
OFF
1-4 Active locking only Passive locking
1-5 Panic w/ ignition No Panic w/ ignition
1-6
Door lock pulse duration:
Opt 1: 0.8 sec
Opt 2: 3.5 sec
Opt 3: 0.4 sec
1-7 Forced passive arming ON
Forced passive arming OFF
1-8
Automatic Engine Disable ON
Automatic Engine Disable OFF
1-9 Armed When Driving Vehicle Recovery System (VRS)
1-10 Code Hopping™ ON Code Hopping OFF
Reset and Delete
Important: TheDelete all transmitters & Reset features’ option resets all
programmed settings to their default factory state. Before performing this
procedure, it is recommended to make note of all programmed changes.
1.
Open a door.
2.
Turn the ignition ON.
3.
Press and release the Control Center button 9 times and then press and
hold the Control Center button once more. The siren chirps and the LED
blinks 9 times indicating the Delete all transmitters & Reset features
channel is accessed. Do not release Control Center button.
4.
While holding the Control Center button, press the LOCK button on any
paired remote control. The siren chirps indicating the Delete all transmit-
ters & Reset procedure was sucessful and chirps again to conrm exit from
programming routine.
Programming routine exits if any of the following occurs:
The open door is closed
The ignition is turned OFF
There is no activity for 15 seconds
The Control button is pressed too many times
Menu 2: Advanced Features
Feature
#
Option 1 setting Option 2+ setting
2-1 Siren
Horn Honk
2-2 30 second siren duration 60 second siren duration
2-3 NPC®:
ON
NPC: OFF
2-4 Progressive door trigger
Instant door trigger
2-5 Override pulse count: 1
Override pulse count: (2), (3), (4), (5)
2-6 Door trigger error chirp: ON Door trigger error chirp:
OFF
2-7
Ignition controlled dome light:
ON
Ignition controlled dome light:
OFF
2-8
Single unlock pulse
Double unlock pulse
2-9
Single lock pulse
Double lock pulse
2-10
Channel 3 functionality:
Opt 1: Validity
Opt 2: Latched
Opt 3: Latched reset with ignition
Opt 4: Timed (30-Second)
Opt 5: Factory Alarm Disarm
Opt 6: Factory Alarm Trigger
Opt 7: Second Unlock Output
2-11
Comfort Closure: (ON, 20 sec) Comfort Closure: OFF
2-12 Real Panic Sound: ON Real Panic Sound: OFF
Long Term Event History
The system stores the last two full triggers in memory. These are not erasable.
Each time the unit sees a full trigger, the older of the two triggers in memory is
replaced by the new trigger. To access long term event history:
1.
With the ignition OFF, press and hold the Control Center button.
2.
Turn the ignition ON.
3.
Release the Control Center button.
4.
Within 5 seconds, press and release the Control Center button. The status LED
flashes (in groups) indicating the last two security zones triggered the system.
This will occur for 60 seconds or until the ignition is turned OFF.
Refer to ‘Table of Security Zones’.
Note: The Warn Away triggers are not stored to memory and are not reported.
Table of Security Zones
It is recommended to test each security zone after installation to ensure proper
functionality. After triggering the alarm, the status LED will ash 1- 5 times
identifying each input zone as shown below:
Zone Description Input Description
1
Instant trigger: input
Blue Wire (12-pin harness)
2
Instant trigger (Heavier impact
detected by the shock sensor)
On-board Shock Sensor.
3
Door switch trigger
Green or Violet Wire (12-pin harness)
4
Instant trigger: optional sensor Sensor Port (optional)
5
Ignition trigger Yellow Wire (12-pin harness)
DirectLoader / Bitwriter - Only Options
DirectLoader
Bitwriter
Bitwriter programming gives you access to a wider range of system
options. These features and the adjustments that may be
programmed are described under the Bitwriter section in the full
online guide. Feature Programming (learn routine) can only be locked
and unlocked with the Bitwriter option.
Example of options:
Menu
Item
Feature Default Option 2
1
Ignition Controlled
Lock
Ignition Controlled
Lock ON
Ignition Controlled
Lock OFF
2
Ignition Controlled
Unlock
Ignition Controlled
Unlock ON
Ignition Controlled
Unlock OFF
3
Siren Duration
30 second siren
duration
1-180 seconds (in 1
second increments)
Guide Translations
For a Spanish (La traducción al Español) or French (Traduction en française)
version of the Installation Guide, please download it from www.directechs.com
under “Resources”.
Scan QR for full Installation Guide
Looking for replacement parts?
The full installation manual now includes individual part numbers for each
item included in this kit (ex. P/N: 150 -112233).
Scan QR code below for more information.
© 2024 DIRECTED by VOXX. All Rights Reserved. 510-10684 (R 1.0)


Produkt Specifikationer

Mærke: Viper
Kategori: Bilalarm
Model: 3108V

Har du brug for hjælp?

Hvis du har brug for hjælp til Viper 3108V stil et spørgsmål nedenfor, og andre brugere vil svare dig




Bilalarm Viper Manualer

Viper

Viper 3108V Manual

10 Juli 2025
Viper

Viper 4606V Manual

6 Juli 2025
Viper

Viper 4105V Manual

9 April 2025
Viper

Viper 3105V Manual

19 August 2024
Viper

Viper 211HV Manual

21 Juli 2024
Viper

Viper 3606V Manual

20 Februar 2023
Viper

Viper 3121V Manual

28 Oktober 2022

Bilalarm Manualer

Nyeste Bilalarm Manualer

Gemini

Gemini 7463 Manual

23 September 2024
Gemini

Gemini 7090 Manual

20 September 2024
Gemini

Gemini 7502 Manual

15 September 2024
Audiovox

Audiovox CA1155E Manual

29 August 2024
HP

HP Rotary Lock Manual

26 August 2024
Spy

Spy FM5000 Manual

23 August 2024
Gemini

Gemini 823 Manual

22 August 2024