JETI JEX-MULI6S Manual

JETI Radiostyret legetøj JEX-MULI6S

Læs gratis den danske manual til JETI JEX-MULI6S (4 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 8 anmeldelser. Har du et spørgsmål om JETI JEX-MULI6S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Sensor MULi6s EX

-1-

The MULi6s sensor is used for monitoring the voltage of lithium based batteries and can measure the

voltage of individual battery cells using the 7-pin balance connection. With the help of this sensor it is

possible to monitor the minimum and maximum cell voltage as well as the total battery voltage. Not only

that, but the Duplex system allows for alert conditions to be deﬁned, in order to sound an audible alarm

when voltages drop below desired levels.

The unit uses the 2.4GHz band to communicate, not only allowing data to be sent from the transmitter to

the receiver, but also allowing the receiver in the model to transmit data back to the user. In this manner,

telemetric data obtained during operation is transferred in real-time and the current state of the system can

be presented on the LCD screen of the Jeti Box.

Dimensions

36 x 20 x 5 mm

Weight (with cables)

6 g

Accuracy

0 – 4.4V

Operating Temperature

- 10°C +85°C

Input voltage

3.5 8.4 V –

Current draw

9 mA

Parameter settings for MULi6s

All parameter settings and data readouts must be performed through the Jeti Box (available separately).

After connecting, the sensor identiﬁcation, the number of cells connected to the unit, the lowest cell voltage

and the number (#) of the cell with the lowest voltage are shown on the LCD screen of the Jeti Box. By

pressing the Down button of the Jeti Box, the MULi6s sensor menu is displayed.

MULi6s MENU: Actual Value – Pressing the down button selects between displaying the following actual

measured values:

Individual voltage – By repeatedly pressing the D button, the voltage of each connected cell is shown

MULi6s MENU: MIN / MAX – Navigating the menu of the Jeti Box allows the minimum and maximum

extremes of voltage be viewed. These values are automatically erased from the sensor when the

conﬁgured trigger level is next exceeded. Alternatively the values can be erased manually using the the

Setting



Erase Data optio n.

U MIN/MAX – Shows the minimum and maximum voltage of the currently selected cell. Using Up and Down

keys moves between the cells, showing the Min/Max voltage and the cell number (#) for the corresponding

cell.

MULi6s MENU: Setting – Using the ‘down’ bu tton of the Jeti Box, the following options can be accessed

within this menu:

Erase data – By simultaneously pressing the left and right arrow buttons, all measured parameters will be

erased.

Start Trigger – Set the voltage at which monitoring will begin and any existing data will automatically be

erased. Use the Left and Right buttons to set the per-cell voltage.

Beep Alarm – Set the letter of the Morse code to be represented by the alarm from the transmitter, when a

low-voltage condition is encountered.

Beep Error - Set up of a morse code letter representing a battery error. If after an identiﬁcation sequence

the number of battery cells changes, a battery error will be generated and this error will be announced

acoustically by emitting the above mentioned morse code letter. This function may be deactivated by

pushing and holding of the button L (left).

MULi6s MENU: ALARMS – Using the down button, it is possible here to change settings for individual

alarms.

Low Volt. Alarm – Set the threshold at which an alarm will be generated and your Tx module will emit the

sound specified by the ‘Beep Alarm’ letter specified in ‘Settings’. This value can be Off, or between 0 and

4.4V per cell.

Sensor MULi6s EX

-2-

MULi6s MENU: SERVICE – by pressing button D (arrow down) you will change to depiction of the ﬁrmware

version and to renewal of the sensor default setting.

Factory Defaults by simultaneous pressing of arrows R and L (right and left) the factory settings of the –

MULI6s are loaded.

MULI6S v. xx.xx ID xxxxx:xxxxx product marking with ﬁrmware version and series number (ID). –

IMPORTANT: Order of connection:

– Connect the sensor to your lithium-based battery via the balance connector (Please note correct polarity)

– Connect the sensor to the receiver or expander

– Connect negative battery terminal to negative ESC/BEC terminal

– Connect positive battery terminal to positive ESC/BEC terminal

Connecting the battery to the sensor

Your lithium-based battery should be connected to the sensor via the balance plug on your battery. Please

observe the correct polarity. After connecting, the sensor requires approximately 2 seconds to determine

the number of cells connected. During this time the screen of your Jeti Box will indicate progress. If a

battery with a diﬀerent number of cells is connected, the sensor will report an error and must be

disconnected from its power supply.

Connecting the MULi6s sensor

1. The three-wire cable with JR connector may be connected directly to the Jeti Box using the Pulse/+/-

socket. A power source of 3.5-8.4V must be supplied via the Jeti Box using the +/- socket to power the

module. In this conﬁguration the MULi6s sensor can operate as a stand-alone mobile unit, providing

measurements on the screen of the Jeti Box. No alarm signals are generated with this conﬁguration,

because these are provided by the transmitter module, which is not connected. Alerts are displayed only on

the LCD screen.

2. Connect the three-wire cable with JR connector directly to the Ext. socket on the Duplex receiver. In this

conﬁguration the sensor is powered via the receiver. Switching on the transmitter and receiver allows the

sensor to be conﬁgured appropriately for your power system and alarm settings to be deﬁned.

Produkt Specifikationer

Mærke:	JETI
Kategori:	Radiostyret legetøj
Model:	JEX-MULI6S

Har du brug for hjælp?

Hvis du har brug for hjælp til JETI JEX-MULI6S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj JETI Manualer

JETI TD1609S Manual

21 August 2024

JETI JDEX-RR7 Manual

21 August 2024

JETI JEX-MF2G-800 Manual

21 August 2024

JETI Central Box 220 Manual

21 August 2024

JETI MEZON 75 opto (RPM) Manual

21 August 2024

JETI Central Box 210 Manual

21 August 2024

JETI Duplex Rsat 2 EX Manual

21 August 2024

JETI JM-090-L Manual

20 August 2024

JETI TD0905L Manual

20 August 2024

JETI AddCAP 1640 Manual

20 August 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

Silvergear RC Dino Manual

17 Juni 2025

FMS 1/18 FCX18 Chevrolet K10 V2 Manual

16 Juni 2025

Amewi 21108 Manual

15 Juni 2025

Amewi 21107 Manual

10 Juni 2025

Amewi 21106 Manual

8 Juni 2025

ECX 1.9 4WD Barrage 01009 Manual

7 Juni 2025

ECX Kickflip 00010 Manual

4 Juni 2025

ECX 1/10 2WD Circuit 03130T2 Manual

2 Juni 2025

ECX AMP Crush Manual

2 Juni 2025

ECX Ruckus 03009 Manual

2 Juni 2025