Jindara Kimberley Mk2 Manual

Jindara Varmeapparat Kimberley Mk2

Læs gratis den danske manual til Jindara Kimberley Mk2 (2 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Jindara Kimberley Mk2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Compact Zero Clearance

Cabinet Installation

ZCC Part No. 225333

Installation notes:

The Gason Zero Clearance Cabinet is an approved cabinet that allows for Eureka/Jindara Insert woodheaters as stated above to be installed within

replace in accordance with AS :2001.2918

This can be achieved by following the installation guidelines listed below.

• Select the po n that you wish to to install your ZCC , carsitio roof cavity (The outer

being 255mm requires a 25mm clear ce on either side to combustibles, making overall clearance 305mm).an

•

• . Note: Line up centre holes with corresponding holes depending on model. Refer to diagram on sheet 2.

• Fit the to the upstands and terminate at the required height above the roof line.

• Fit 300mm x 100mm vermin proof vent directly behind where the will be located, as near as practicable to the r. This vent will

allow air access to the zero box either from another room or external air. Note, if installed on r, an additional two vents are

required. i.e. Either thr r, one each side of the zero box, or alternatively, through the side wall(s), if applicable.

• Build your frame around the

m aining the clearances listed above.ant

•

• Cover the rest of the frame to suit your requirments with plaster, timber, MDF etc.

•

• Install the mantel if required. Note if mantle is made out of a combustible material the following dimensions must be adhered to.

All dimensions are minimum and must under no circumstances be reduced. Gason Pty Ltd accepts no liability whatsoever for their

interpretation of AS :2001.2918

Sheet 1 NEXT 2 GPN 231080 Rev.A

545

763 Zero

Clearance

Box

To suit Insert models: Opal SRS4, Riverina SRS3,

A min. gap for60mm

Opal SRS4/Riverina SRS3

and gap for 120mm

Stockade SRS5/Barossa SRS3

timber stud.

The timber stud may need

to be notched out to allow

for the minimum required

Stockade SRS5, Barossa SRS3, Kimberley Mk2, Hamersley Mk2

Federation Mk2 & Victorian Insert

NOTE:

Tripleskin

Flue

690

660

836

MODEL A B C D E F G H I J

Opal

Riverina

Stockade

Barossa

Kimberley

Hamersley

Federation

Victorian

Hearth Width

12 570 890 810 40 20 1040 1100 50 250 530

12 550 950 810 40 20 1340 1390 50 250 510

18 615

18 705 1000

All dimensions in millimetres, images not to scale

Clearance to combustibles

Insert your chosen appliance into the zero cabinet. Note: p1-x2 galvanized c-section brackets supplied are required to centralise

Opal/Riverina, Stockade/Barossa. For installation of Kimberley, Hamersley, Federation and Victorian, appliances must sit on c-section

to ensure correct installation height is achieved. Fit active ue and cowl once appliance is in position.

See oversheet for dimensions.

(non-combustible cement sheet, villaboard or similar) in the position desired for the ZCC, ensuring hearth will

1140 25 250 550 940 1063 100 50 1050

12 570 890 810 40 20 1040 1100 50 250 530

12 550 950 810 40 20 1340 1390 50 250 510

18 705 1000

1063 100 50 975 1225 150 250 600

Cover the front face of framing with a minimum 4mm cement sheet or non-combustible material.

A. F.

mm in front

of unit

Hearth depth

the ZCC

ZCC

extend fully underneath ZCC as shown above for relevent model. Place the ZCC into position.

Sheet 2 NEXT - GPN 231080 Rev.A

6 inch Flue Kit (Eureka & Jindara)

Spigot

3rd Skin

2nd Skin

1st Skin

Heater

10” Upstand

• 10” Upstands

55mm

97mm

• 8” Upstand

10” Gal Flue

8” Gal Flue

6˝ S/S Flue

8” Upstand

425mm

370mm

10”

8”

450mm

370mm

4th Skin

Non-combustible

hearth

Breast plate no

thicker than 30mm

(appliance to

mantle upright)

(max)

2 petS1 petS

Plaster, timber, MDF etc.

Minimum 4mm thick

cement sheet, villaboard

or non-combustible

material on front face

of framing

Minimum Requirements:

• 5 x 6” S/S Flue

• 4 x 8” Gal Flue

• 4 x 10” Gal Flue

Note: Some states will use dierent size ue kits

which will require the appropriate upstand.

Non-combustible material can

overlap clearance gap between

ZCB and frameing, and run over

the front of the ZCB. DO NOT

silicon or adhear material to ZCB

as heat expansion of ZCB will

cause cracking.

Vent - Position vent

such that access is

available to fan power

supply when vent is

removed.

NOTE: Position of upstands on Zero Box di ers depending

on model type. Line up centre screw hole on Zero Box with

corresponding notch on upstands.

Barossa, Stockade

& Kimberley Models

Opal & Riverina

Models

Hamersley Models

Victorian Insert

& Federation Models

Hearth depth

mm in front

of unit

Vent may be

located in the

wall of on the oor.

Compact Zero Clearance

Cabinet Installation

Produkt Specifikationer

Mærke:	Jindara
Kategori:	Varmeapparat
Model:	Kimberley Mk2

Har du brug for hjælp?

Hvis du har brug for hjælp til Jindara Kimberley Mk2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Jindara Manualer

Jindara Kimberley Mk2 Manual

21 August 2024

Jindara Hamersley MK2 Freestanding Manual

20 August 2024

Jindara Tilga Manual

19 August 2024

Jindara Hamersley Mk2 Manual

18 August 2024

Jindara Riverina Manual

16 August 2024

Jindara Mallee Manual

14 August 2024

Jindara Spectre Manual

14 August 2024

Jindara Grange Manual

13 August 2024

Jindara Gawler Manual

11 August 2024

Jindara Sturt Manual

10 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

Klarstein Wonderwall Air 60 Manual

30 Juli 2025

Panasonic NF-GM600 Manual

29 Juli 2025

Heatstrip THSTAND Manual

29 Juli 2025

Heatstrip Intense Manual

29 Juli 2025

Rowenta Auto Confort BU7500 Manual

29 Juli 2025

TriStar KA-5877 Manual

28 Juli 2025

TriStar KA-5866 Manual

27 Juli 2025

TriStar KA-5869 Manual

27 Juli 2025

Sencor SOH 3111BK Manual

27 Juli 2025

Sencor SOH 3011BE Manual

26 Juli 2025