Jindara Pyrenees Manual

Jindara Varmeapparat Pyrenees

Læs gratis den danske manual til Jindara Pyrenees (4 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Jindara Pyrenees, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

GPN 231590

Pyrenees & Sorrento Freestanding

Operation & Installation Instructions

REV. A

Please keep these instructions for future reference.

woodheating

• Smoke entering the room from the firebox when the door is open may be caused by

• insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)

– increase height of flue.

• flue downdraught

– consult dealer or increase height of flue.

• creosote build up in flue

– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.

• Excessive ash build up

Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the wood which is most

convenient for you as long as it is dry. After a period of time you will get to know when to empty your unit. Always leave 12mm of ash

in the bottom of your heater. Bark will give you excessive ash. Try not to burn it.

If you are burning wood that gives you charcoal, you may find that after running the heater say for eight hours at maximum burn rate,

the charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If you are not ready to shutdown for

overnight burn when you next fuel the stove, load the stove with only one piece of wood and lay it across the firebox on top of the

charcoal. Open the air control wide open and you will find the charcoal will burn down with the one piece of wood. Repeat the process

until the ash level is significantly reduced.

Pyrenees & Sorrento Freestanding

Troubleshooting (Continued)

1. Subject to clauses 2 & 3 of this Warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship and/or materials for the

following periods from the date of purchase:

(a) the firebox for ten years;

(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and

(c) all other components for 12 months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.

2. This extended warranty does not apply:

(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;

(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in accordance with the

instructions provided by Gason; or

3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this Warranty, please contact an authorised Gason service centre to arrange for an

assessment.

4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:

(a) replace the heater;

(b) repair or replace specific components of the heater; or

5. Parts replaced under this Warranty are warranted for the balance of their original warranty period.

6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this Warranty must pay all costs

associated with:

(a) returning the heater; and

(b) the delivery or collection of any new or repaired heater.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which these warranties relate.

These warranties are given by:

A.F. Gason Pty Ltd

Blake Street

Ararat VIC 3377

Please contact us if you have any queries on:

Phone: 03 5352 2151;

or email us via the “Contact Us” section of our website: www.gason.com.au.

Jindara Heating reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.

WARRANTY

Pyrenees & Sorrento Freestanding

Troubleshooting

WARNING

NEVER OPERATE THE HEATER WITH THE DOOR LOOSE AND NOT AIR TIGHT. OVERFIRING

COULD RESULT IN DETRIMENTAL WEAR AND TEAR ON THE FIREBOX.

• Noisy Fan

Turn the power off and remove the three pin plug from the power point. Remove the four screws that hold the front fan access panel.

Remove the panel. Disconnect the wiring loom via the plastic joiner. Unscrew the two nuts which hold the fan in position and remove the

fan. Clean any dust with a dry paint brush and vacuum the fan blades. Clean around the motor. After completion place two or three

drops of sewing machine oil on the shafts at the bearings. Replace the fan in reverse to the removal.

• Fan not working

Check the power connection with another appliance. If the power point is okay assume the Fan or the Switch is defective. Isolate the

power as above. Check that the terminals on the loom and the switch are firmly connected. If the fan then fails to function, remove the

fan and switch by firstly removing the knob off the fan switch by pulling it away from the heater. Undo the holding nut and pull the switch

out. Disconnect the wiring from the power lead and remove the fan and switch. Convey the same to the authorised Jindara Dealer from

whom you purchased your unit for service. Replace in the reverse order.

• Air Control Jamming

Remove air control cover plate by removing the four screws which hold it onto the face of the heater. There are two bolts holding the air slide

in place. Undo them and remove the air slide. Wipe any ash or dust that may have accumulated on the back of the air slide or on the face of

the heater. If any burrs have developed on the back of the air slide or on the face of the heater, rub them off with fine wet and dry sand

paper till you have a smooth surface and edges. Replace the air slide and make sure the washers and spacers are on the bolts when you

screw the bolts back into the face of the heater. Do not apply any type of lubricant to the air slide whatsoever as this will attract dust and

make the slide stick.

• No Overnight Burn

Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heater. If it is loose, tighten up the

bolts holding the air slide to the face of the heater. Do not overtighten.

Check that the door rope has an even indentation from the sealing strip, which is on the face of the firebox. If it is uneven and it appears as

though air could leak through the seal, adjust the thickness of the door rope to suit. Stretch the rope to make it thinner where the indentation is

the heaviest and bunch up the excess where the indentation is smaller.

Check the four bolts that hold the glass retainer in position. If loose tighten. Do not overtighten.

The door may become loose through the door seal shrinking. To tighten the door, open the door and look at the inside of the door catch. Undo

the nut which is holding the latch plate. Remove the latch plate. Remove one thick washer and the star washer. Refit the latch plate. The latch

plate is concave to provide a lead in edge so that there is smooth connection between the door latch and the catch. Make sure that the face of

the latch that is curved outward is facing towards the door.

Replace the nut. When closing the door you should now feel firm resistance when the latch comes into contact with the catch.

Overfiring

Pyrenees & Sorrento Freestanding

WARNING

Read and follow these instructions carefully before installing and using this appliance.

SAVE THESE INSTRUCTIONS

Paint Curing and Care

WARNING

• A flue fire with resulting damage may occur if this appliance is not installed, operated and

maintained as per this booklet.

• Never place combustible material such as wood, paper or furniture near the appliance.

• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood, flammable

liquids or any substance containing salts or corrosives.

• This appliance must not be installed and operated in an area where kerosene, petrol, paint

thinner or other flammable liquid is used or stored.

• The flue system must be inspected and cleaned annually or sooner if required. Failure to

do so could result in an excessive build up of creosote which may result in a flue fire

which may damage the flue or cause damage to your home.

• The surface of the appliance becomes hot during operation. Do not touch the surface of

this appliance. Keep children away from the appliance during operation. Do not allow

anyone to operate this appliance who is not familiar with the instructions in this booklet.

WARNING

Your heater is coated with the best available heat resistant paint. Even though the paint has

been baked after application, it may require further temperature curing. It may, if you overfire

the heater on its first fire, discolour. For your first two or three firings, never exceed medium

air setting and always have the fan on when above low burn. Do not wipe the heater while the

paint is curing. After the paint has cured the only maintenance required to maintain the

heaters finish is to wipe it with a soft cloth. Do not use any commercial cleaners or solvents

on the paint finish.

We are proud of the presentation of our products. If at any time you need to freshen up the

paint finish, your local dealer has touch up paint available for purchase. You may even change

the colour of your heater if you wish.

If you have any enquires, please contact the dealer from whom you purchased your heater:

PLEASE COMPLETE:

Dealer Name

Dealer Address

Phone

Please attach your original purchase dockets to this booklet for future reference.

Safety Warnings

Produkt Specifikationer

Mærke:	Jindara
Kategori:	Varmeapparat
Model:	Pyrenees

Har du brug for hjælp?

Hvis du har brug for hjælp til Jindara Pyrenees stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Jindara Manualer

Jindara Kimberley Mk2 Manual

21 August 2024

Jindara Hamersley MK2 Freestanding Manual

20 August 2024

Jindara Tilga Manual

19 August 2024

Jindara Hamersley Mk2 Manual

18 August 2024

Jindara Riverina Manual

16 August 2024

Jindara Mallee Manual

14 August 2024

Jindara Spectre Manual

14 August 2024

Jindara Grange Manual

13 August 2024

Jindara Gawler Manual

11 August 2024

Jindara Sturt Manual

10 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

XPower B-55 Manual

14 Juni 2025

XPower B-2 Manual

14 Juni 2025

XPower M-27 Manual

14 Juni 2025

B-Air Vent VP-34 Manual

14 Juni 2025

XPower P-80 Manual

14 Juni 2025

DeLonghi JRE0812 Manual

14 Juni 2025

Aura CF15120B Manual

14 Juni 2025

XPower B-4 Manual

14 Juni 2025

Tornado 98784 Manual

14 Juni 2025

Powr-Flite PDF5 Manual

13 Juni 2025