JL Audio 13W7AE Manual

JL Audio Subwoofer 13W7AE

Læs gratis den danske manual til JL Audio 13W7AE (16 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om JL Audio 13W7AE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

W7AE Owner’s Manual

YELLOW OPTIMUM:

This zone represents the best balance

between long-term reliability, high

output and low distortion performance.

In this zone, you will be taking full

advantage of the woofer's optimum,

low-distortion performance range

without undue risk of failure.

RED MAXIMUM:

In this zone, low-distortion output and

long-term reliability will be compromised

(especially by an aggressive user). Slightly

more SPL will be gained by pushing the

power into this zone, but typically not

more than 2dB, compared to the yellow

zone. The closer you are to the black

zone, the higher the likelihood of driver

failure. Operate with caution.

BLACK WARRANTY VOID:

We do not recommend operating

woofers at this level of power. In this

zone, there is a very high probability that

the driver will fail due to excessive heat

and/or mechanical stress.

Subwoofer drivers operated at

these levels of power are NOT covered

under warranty.

GREEN MINIMUM:

From a reliability standpoint, this zone

represents a very comfortable operating

power range for each driver. This level

of power will not stress the woofer but

will not extract all of its performance

potential, either.

Use of less than the minimum power

level will not damage the woofer, but may

result in unsatisfactory performance.

An Introduction

When designing systems with W7AE drivers, it is very important to achieve a good power match between the subwoofer amplifier and the subwoofer driver's capabilities. The power levels listed in the

above chart represent continuous (RMS) amplifier power per woofer and assume that the user will regularly make full use of that power without drastically overdriving (clipping) the amplifier(s). Make

sure you factor system impedance and the total number of subwoofers into your calculations. Adhering to these power recommendations will result in systems that are both reliable and enjoyable.

RECOMMENDED CONTINUOUS RMS POWER RANGE FOR ONE SUBWOOFER DRIVER:

250W 500W 1000W 2000W 4000W125W

13W7AE

12W7AE

10W7AE

8W7AE

Thank you for purchasing a JLAudio W7AE subwoofer driver.

The W7AE embodies JLAudio’s commitment to pushing the

envelope of speaker technology. Each W7AE model has been

meticulously engineered to reproduce sub-bass with extreme

fidelity at any volume level, provided it is installed and tuned

properly. Please review the information in this document carefully

to maximize your enjoyment of the W7AE’s capabilities.

Two enclosure recommendations are listed for each model,

one sealed and one ported. In most cases, the sealed enclosure

design will give you the best overall sound quality and take up the

least space in your vehicle. The ported enclosure design will deliver

additional output over the sealed enclosure (about 3 - 4 dB more)

and will also maintain excellent sound quality, but it will require

significantly more space to install. The recommended ported

enclosure is not designed for peaky “competition SPL” performance,

but rather for music listening. It will be very loud and sound

extremely good when set up properly.

Please note that W7AE’s rarely require any equalization to

produce smooth frequency response. They also do not generally

benefit from excessively low crossover points. We recommend

that you use crossover points at or above 80 Hz in most cases.

This will ensure that you get maximum benefits from the W7’s

low-frequency output capabilities, while simultaneously reducing

the burden on your main speakers. This helps to reduce distortion

and improve overall fidelity.

For optimum sub-bass performance, the amplifier input

sensitivity must be adjusted to avoid excessive distortion (clipping)

of the amplifier output. Overly high input sensitivity settings

result in no additional clean output but will result in poor sound

quality and reduced speaker reliability. With W7AE subwoofers,

a clipped amplifier output may manifest itself audibly as a low-

level “mechanical” sound coming from the speakers. Proper input

sensitivity setting will avoid this problem.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Subwoofer
Model:	13W7AE

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio 13W7AE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Subwoofer JL Audio Manualer

JL Audio Fathom CTS-113-MD900-13TW5H Manual

7 September 2025

JL Audio Fathom CTS-113-TT525-13TW5H Manual

7 September 2025

JL Audio Stealthbox SB-IN-G35CPE/10W1v2 Manual

27 Juli 2025

JL Audio 8W1v2-4 Manual

27 Juli 2025

JL Audio Stealthbox SB-H-PIO7/10TW3 Manual

27 Juli 2025

JL Audio Stealthbox SB-GM-SLVCRW/10TW3 Manual

30 December 2025

JL Audio Stealthbox SB-F-MUCUPE2/13W3v3 Manual

30 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/GA Manual

30 December 2025

JL Audio Stealthbox SB-N-370/10W3v3 Manual

8 December 2024

JL Audio Stealthbox SB-GM-CTRIP/10TW3/UF Manual

8 December 2024

Subwoofer Manualer

Nyeste Subwoofer Manualer

Audison Prima APBMW S8-2.2 Manual

28 September 2025

Audison Prima APBMW S8-4.2 Manual

28 September 2025

Boston Acoustics BT1100 Manual

25 September 2025

Boston Acoustics Classic CPS 10Wi Manual

25 September 2025

Boston Acoustics Classic CPS 8Wi Manual

24 September 2025

Boston Acoustics Classic CPS 12Wi Manual

24 September 2025

Ground Zero GZRW 250-D2 FLAT Manual

24 September 2025

Ground Zero GZNW 38NEO-SPL Manual

24 September 2025

Ground Zero GZIW 200 Manual

24 September 2025

Ground Zero GZIW 250 Manual

24 September 2025