JL Audio PS-SWMCP Manual

JL Audio Højttaler PS-SWMCP

Læs gratis den danske manual til JL Audio PS-SWMCP (3 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om JL Audio PS-SWMCP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Installation Instructions for all

PS-SWMCP

swivel fixtures for round pipes

P I PE M O UN T I N G FIX T URE S ( S W I V EL)

FOR PS650VeX™ ENCLOSED SPEAKER SYS TEMS

NOTE: The PS-SWMCP-B-2.000 Fixture and PS650-VeX-SG-TMB Enclosed Speaker

System are used in this manual for illustrative purposes only. The fixture installation

steps are the same for all PS650-VeX Enclosed Speaker Systems and all PS-SWMCP

swivel fixtures for round pipes.

LIMITED WARRANTY  MARINE PRODUCTS USA

JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the

original date of purchase.

This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service

be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),

repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not

covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages

and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning

with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product

thereafter. Some states do not al low limitations on impl ied warranties, therefore these exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For Service Information in the U.S.A. please call

JL Audio Customer Service: (954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025, USA

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

w w w . j l a u d i o . c o m

JL Audi o® and the JL Audi o logo are re gistered t rademar ks of JL Audi o, Inc. “Ahead of t he Curve” an d its respe ctive lo go is a trade mark of JL Audio, Inc.

©2016 JLAudio, Inc. • For more det ailed inf ormation please visit us online at w ww.jlaudio.com. Due to our policy of continuo us produc t develop ment, all sp ecifications are su bject to change witho ut notice.

SKU# 011498

Printed in U.S.A. • 092817

Mounting Fixture is made in the USA by Axia Alloys

Protected by US Patents #8,136,771 & #8,398,035

Included Hardware: BOM ID Quantity Description

1 4 Axia Alloys Strap Clamp

2 6 M6 x 16 mm Socket Cap Machine Screw

3 2 M4 x 4 mm Set Screw (pre-installed)

4 4 M6 Nylon Insert Locknut

5 2 Clamp Receiver

6 1 Loctite® Red read-Locking Compound

7 4 M6 Flat Washer

8 4 M6 x 45 mm Socket Cap Machine Screw

9 1 Plastic Strip

10* 2 Fixture Base

11* 1 Silicone Adhesive

12* 12 #8 Flat Washer

13* 12 #8 x 1-1/4” Pan Head Screw

* Included with VeX™ speaker enclosures.

(hardware pictured for one)

Note: Not all wires may be used in normal applications.

Wire Size Wire Color Use

16 AWG Red/Stripe Speaker Positive (+)

Black/Stripe Speaker Negative (–)

20 AWG

Red Not Used

Green Not Used

Blue LED Positive (+)

Yellow LED Negative (–)

Wire Size Wire Label Use

16 AWG “ ”+Speaker Positive (+)

N/A Speaker Negative (–)

For Premium Models:

For Standard Models:

Loosen the pre-installed M4 x 4 mm Set Screw in the

clamp receiver. Slide an M6 x 16 mm Machine Screw

through the center hole of the clamp receiver, into the

center hole in the xture base, and hand tighten.

If you wish to rotate the speaker’s grille/logo badge

alignment, remove the six #8 x 1-1/4” speaker mounting

screws and #8 Flat Washers.

Apply Loctite® red thread-locking compound to two M6

x 16 mm Machine Screws, slide them through the slots

in the clamp receiver, into the appropriate holes in the

xture base, and fully tighten.

Secure the clamps to the clamp receiver using a pair of

M6 x 45 mm Machine Screws, M6 Flat Washers, and M6

Locknuts as illustrated. e locknut should be installed

into the hex shaped recess on one end of each clamp.

Hand-tighten, allowing just enough freedom to rotate the

enclosure around the pipe.

Realign the clamps with the clamp receiver on the

enclosure, and secure them to the clamp receiver using a

pair of M6 x 45 mm Machine Screws, M6 Flat Washers,

and M6 Locknuts as illustrated, and fully tighten. Note:

e locknut should be installed into the hex shaped

recess on one end of each clamp.

Place the supplied plastic strip around the pipe to

prevent scratching. Push the clamps over the pipe

(remove the plastic strip). Align the clamps with the

clamp receiver on the enclosure.

Remove the center M6 x 16 mm Machine Screw from the

clamp receiver, apply Loctite® red thread-locking

compound, reinstall, and fully tighten.

Position the enclosure at the desired location, tightening

the M6 x 45 mm Machine Screws as necessary. Fully

tighten the pre-installed M4 x 4 mm Set Screw in the

clamp receiver to hold its position. Mark the location

of the clamps on the pipe, then remove the enclosure

from the pipe.

Rotate the speaker to the desired angle. Reinstall the

speaker and speaker mounting screws and washers.

Hand-tighten in a criss-cross pattern.

Remove adhesive backing and install the JL Audio logo

badge.

Remove the backing from the rear logo appliqué. With

the logo positioned at the desired angle, attach the

appliqué to the back of the enclosure.

Gently press on the appliqué from the center out to

remove any air pockets.

Clean the inside of the aluminum cap with acetone (not

included) prior to attaching it to the enclosure. Apply a

circular bead of silicone adhesive to the inside of the

aluminum logo cap, 1/2-inch (13 mm) from the outer edge.

Align the aluminum logo cap to the desired angle of

rotation, and press it onto the back of the enclosure.

Apply masking tape (not included) to hold the cap in

place until the silicone cures (at least 24 hours).

• For marine installations, do not connect the speaker’s LED lights to the vessel’s navigational lighting circuits.

• For short-circuit protection, install a supplied fuseholder onto EACH speaker’s BLUE (+12V) LED power connection lead.

• Connect all BLUE (+12V) leads together (parallel) and connect to a switched +12V supply. Connect all YELLOW (GND)

leads together and connect to a negative ground or to the NEGATIVE battery post.

• We recommend activating the speakers’ LEDs thru a lighting circuit that supplies +12V via an existing switch. If an

existing switched circuit is not available, you may install a dedicated toggle/rocker style switch that will supply positive

(+12V) power. Fuse this connection according to how many LED circuits you have (LED circuits x 150 mA).

[ D]GN

LED

[+12V]

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

LED

Fuse

Example: One speaker pair of

LED circuits connected in parallel.

Steps 11-12 are for Standard Models Only

Steps 13-14 are for Premium Models Only

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Højttaler
Model:	PS-SWMCP

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio PS-SWMCP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler JL Audio Manualer

JL Audio M6-103EWS-Gw-C-3Gw Manual

27 Juli 2025

JL Audio C1-650se Manual

27 Juli 2025

JL Audio M3 Manual

3 April 2025

JL Audio C6-275cm Manual

7 Februar 2025

JL Audio C2-650 Manual

16 November 2024

JL Audio C1-690tx Manual

7 Oktober 2024

JL Audio M3-770X Manual

16 September 2024

JL Audio CF-275mt Manual

1 September 2024

JL Audio C6-100ct Manual

1 September 2024

JL Audio C6-650 Manual

1 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

The Box Pro DSX 110 M Manual

1 August 2025

Muse M-968 BTY Manual

1 August 2025

Grundig Portable 360 Manual

1 August 2025

Grundig Band 360 Manual

1 August 2025

Grundig GBT Connect 360 Manual

1 August 2025

Muse M-968 BTR Manual

31 Juli 2025

JLab Epic Party Manual

31 Juli 2025

JVC XS-E423 Manual

30 Juli 2025

SoundTube RF31-EZ-T Manual

30 Juli 2025

Valcom VIP-480AL-W-SA Manual

30 Juli 2025