JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 Manual

JL Audio Ikke kategoriseret Stealthbox SB-GM-HUMRH3/10W1v3

Læs gratis den danske manual til JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 10 anmeldelser. Har du et spørgsmål om JL Audio Stealthbox SB-GM-HUMRH3/10W1v3, eller vil du spørge andre brugere om produktet?

Side 1/4
INSTALLATI ON
D I F F I C U L T Y :
I N S T A L L A T I O N G U I D E
for the
SB-GM-HUMRH3/10W1v3
SKU# 94196
2006 - 2010 Hummer H3
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With
proper installation, your new vehicle-specific enclosed subwoofer system will deliver years
of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary
tools and experience to disassemble and reassemble your vehicle properly. Also, keep in
mind that your warranty coverage extends to 2 year if your system is installed or approved
by your authorized JL Audio dealer. If you prefer to perform your own installation, please
read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove any contents from the rear cargo area and lower the
rear seats forward.
Continued on Next Page
S T E P 2
The drivers side rear plastic inner fender needs to be
removed.
Using a 10mm socket and ratchet, remove the 5 bolts.
Using a Phillip® head screw driver, remove the 2 screws.
S T E P 3
Pop out the 5 plastic pop-rivets.
The plastic inner fender will drop down.
SB-GM-HUMRH3/10W1v3_ 011215
35
OUT
OF
S T E P 9
With a 10mm socket and ratchet, remove the four bolts that
hold the factory woofer system into place.
Unplug the amplifier and remove the woofer system out of
vehicle.
S T E P 1 1
Thread in the supplied socket cup set screw into the thread-
ed insert, located on the bottom of the Stealthbox®.
Leaving 1/2-inch exposed.
S T E P 1 0
After the factory woofer system has been removed, look
down into the cavity. There is a rubber matting that lays on
top of the wheel well. Cut the front half of this matting out.
Place the wax square to the proper measurements, 3" from
the side wall and 5-1/4-inch from the front wall.
Continued on Next Page
SB-GM-HUMRH3/10W1v3_ 011215
S T E P 7
Remove the top panel.
S T E P 6
With a Phillip® screw driver, remove the screw that is located
under the cover panel.
With a T-50 Torx bit and ratchet, remove the seat belt loop.
S T E P 5
At the driver’s side rear door, remove the door sill.
S T E P 4
From the cargo entrance, remove the weather stripping.
Start at the lower middle. Pull off just past the driver side
paneling.
S T E P 8
Remove the lower panel.
Page 2 • JL Audio, Inc 2016
5 - 1 / 4 "
3 "


Produkt Specifikationer

Mærke: JL Audio
Kategori: Ikke kategoriseret
Model: Stealthbox SB-GM-HUMRH3/10W1v3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 stil et spørgsmål nedenfor, og andre brugere vil svare dig