Joy-It SEN-CCS811V1 Manual

Joy-It Ikke kategoriseret SEN-CCS811V1

Læs gratis den danske manual til Joy-It SEN-CCS811V1 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Joy-It SEN-CCS811V1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

AIR QUALITY SENSOR

SEN CCS811V1-

1. GENERAL INFORMATION

Dear customer,

Thank you for purchasing our product. In the following, we will show you

which things should be observed during the use.

Should you encounter any unexpected problems, do not hesitate to

2. INSTRUCTIONS FOR USE

When using this module, please note that you must perform a so called -

Burn In. This means that for the first 48 hours you will take measure--

ments with the sensor in the mode of your choice. This is because the re-

sistances and sensitivity changes within these first 48 hours, which makes

the measurement results inaccurate within this time.

There is also the so called Run In. This means that within the first 20 mi-- -

nutes aer the sensor has been idle for a long time or aer changing mo-

des, the sensor must stabilize before it can generate accurate data.

The so called modes, which this sensor has, designate the time intervals -

in which measurements are performed. The CCS811 has these modes:

Mode 0 Idle

(no measurements are performed)

Mode 1 IAQ measurement every second

Mode 2 IAQ measurement every 10 seconds

Mode 3 IAQ measurement every 60 seconds

Mode 4 IAQ measurement every 10 ms

(eCO2 and TVOC are not calculated)

In modes 1, 2 and 3, eCO2 and TVOC are calculated each time. Mode 1

reacts fastest to a change, but has a higher operating current. Mode 3

reacts more slowly, but has the lowest operating current on average.

If you change the mode to a slower measuring rate, you should switch to

mode 0 (idle) for at least 10 minutes. This happens, for example, when

you switch from Mode 1 to Mode 3. If you switch to a higher measuring

rate, you do not need to pay any further attention.

Mode 4 is used with an external system. The system receives the raw data

of the sensor to work with it. This allows the measurement rate of one

measurement every 250 ms.

Note: Mode timings are subject to typical 2% tolerance due to accuracy

of internal clock.

Produkt Specifikationer

Mærke:	Joy-It
Kategori:	Ikke kategoriseret
Model:	SEN-CCS811V1

Har du brug for hjælp?

Hvis du har brug for hjælp til Joy-It SEN-CCS811V1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Joy-It Manualer

Joy-It SBC-NodeMCU-ESP32-C Manual

30 Januar 2025

Joy-It COM-RM01 Manual

30 Januar 2025

Joy-It RB-CaseP5-07 Manual

28 Januar 2025

Joy-It SBC-LCD128x64 Manual

14 Januar 2025

Joy-It JT-DPM8650 Manual

1 Januar 2025

Joy-It RB-AlucaseP4 + 01 Manual

27 December 2024

Joy-It RD6006 Manual

4 December 2024

Joy-It RB-Proto+ Manual

4 December 2024

Joy-It SBC-DVA Manual

6 September 2024

Joy-It ARD MEGA2560R3 Manual

5 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025