JUNG 246 EB Manual

JUNG Modtager 246 EB

Læs gratis den danske manual til JUNG 246 EB (4 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om JUNG 246 EB, eller vil du spørge andre brugere om produktet?

Side 1/4
Amplifier for conventional dimmers, built-in
Light Management
Amplifier for conventional dimmers, built-in
Art.-No.: 246 EB
Operationsmanual
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The load is not electrically isolated from the mains even when the device is switched off.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Do not connect any electronic lamps, e.g. switchable or dimmable compact fluorescent
lamps or LED lamps. Device can be damaged.
Fire hazard. For operation with inductive transformers, each transformer must be fused
on the primary side in accordance with the manufacturer's instructions. Only safety
transformers according to EN 61558-2-6 may be used.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
picture 1
(1) Power extension
(2) Load connection
(3) Dimmer connection
3 Function
Intended use
- Output extension of LV dimmers, working according to the phase control principle.
- Output extension of universal dimmers, which have detected an inductive basic load.
In so doing, operation of universal dimmers with an inductive load.
- Connection of incandescent lamps, HV halogen lamps and dimmable inductive
transformers with halogen lamps
- Suitable for mixed operation up to the specified output (see chapter 5.1. Technical data)
- Do not operate the corresponding dimmers without a load
- Installation in false ceilings of surface mounting
1/4
82540013
J:0082540013
11.08.2010
Product characteristics
- Connection of multiple power extensions to one dimmer possible
- Operation using upstream dimmer
- Lamp-beneficial soft start
- Electronic short circuit protection with permanent switch-off
- Electronic over-temperature protection
i Switch-on delay of lamps on power extension of 1 - 2 s
i Brightness differences between the lighting at the dimmer and the lightning at the power
extension are possible.
4 Information for qualified electricians
4.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Fitting and connecting the power extension
i Use the same external conductor for dimmers and power extensions. Do not swap L and N
on the power extension. Otherwise, there is the risk of malfunction.
picture 2
(1) Power extension
(4) Dimmer
o Fit the power extension.
i Minimum diameter of ceiling opening for installation in false ceilings: 63 mm.
o Connect the power extension according to the connection diagram (picture 2).
i In the case of lighting systems with an output of over 3500 W/VA, the installation must be
distributed across two miniature circuit breakers with the same external conductor.
o If multiple circuit breakers supply dangerous voltages to the device or load, couple the
circuit breaker to ensure tripping.
2/4
82540013
J:0082540013
11.08.2010
Light Management
Amplifier for conventional dimmers, built-in


Produkt Specifikationer

Mærke: JUNG
Kategori: Modtager
Model: 246 EB

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG 246 EB stil et spørgsmål nedenfor, og andre brugere vil svare dig