JUNG 804.18 W Manual

JUNG Ikke kategoriseret 804.18 W

Læs gratis den danske manual til JUNG 804.18 W (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om JUNG 804.18 W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Key switches

21.11.20241 / 30024006900

Key switches

Surface-mounted housings

Ref.-no.: 804.18 W, 806.18 W, 833.18 W, 834.18 W

Operating instructions

1 Safety instructions

Electrical devices may only be installed and connected by electrically skilled persons.

Serious injuries, re or property damage possible. Please read and follow the instructions in full.

These instructions are an integral part of the product, and must remain with the end customer.

2 Device components

Fig. 1: Device components

(1) Housing

(2) Insert

(3) Prole half cylinder

(4) Centre plate

3 Function

Intended use

- for prole half cylinder with approx. 40 mm overall length (DIN 18252), e.g. art. no.: 28, 28 G1

Designs

Blind reversing switch, 1-pole (1 motor)

804.18 W

Blind reversing push-button, 1-pole (1 motor)

834.18 W

Push-button (2-way), 1-pole

833.18 W,

Universal-o󰀨 2-way switch, 1-pole

806.18 W

4 Information for electrically skilled persons

Mounting and electrical connection

DANGER

Electrical shock on contact with live parts in the installation environment.

Electrical shocks can be fatal.

Before working on the device, disconnect the power and cover live parts in the area!

Connecting surface-mounted housing

• Feed the cable through the opening in the housing.

For this, use the included sealing gaskets.

• Connect the key switch acc. to the connection diagram. (g. 5 to g 7)

32 45

Key switches

21.11.20242 / 30024006900

Adjusting the cam on the prole half cylinder

180°

0°

300°

240°

210°

330°

30°

60°

90°

120°

150°

270°

Fig. 2 and 3: Adjusting the cam on the prole half cylinder

Example:

- Adjustable cam (6) on a prole half cylinder with 12 positions (0° to 330°)

- Fork (7) of a blind switch in the Stop switching state, for switching states see chapter operation

• Set the cam so that it is either located inside the fork or engages with the fork from the outside after the locking

cylinder has been mounted.

For this, use a screwdriver to press down on the two locking pins (8) and turn the cam into position. Only one of

the two locking pins can be pressed down at a time.

- Cam inside the fork:

The key can only be removed in the Stop or O󰀨 switching state.

- Cam on the outside of the fork:

The key can also be removed in the Up/Down or On switching state.

- Consider the integrated protection against dismounting, see chapter dismounting.

Installing the prole half cylinder

See gure 1

• Fasten the earthing lug (5) and locking cylinder (3) to the centre plate (4) using the included screws.

iIf other locking cylinders are used, these may only have an opening for keys on one side. Otherwise IP44 is not

possible.

Dismounting

Integrated protection against dismounting:

120°

60°

30°

0°

90°270°

240°

150°

210°

Fig. 4: Integrated protection against dismounting

If the cam is in the 0°, 30°, 60°, 90°, 120°, 150°, 210°, 240° or 270° position on the outside of the fork, the centre

plate is secured against unauthorised dismounting.

Dismounting of the centre plate without a key is not possible in this case.

5 Operation

Important:

The key can only be inserted and removed in the 0° position.

• Turn the key in the locking cylinder to the left or right to the following switching states.

Blind switches and push-buttons

The motors connected to the respective terminals run forward or backward depending on the switch position.

Depending on the design, 1 or 2 blind motors can be connected.

Up Motor runs forward.

Stop Motor is switched o󰀨.

Down Motor runs backward.

8 8

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Ikke kategoriseret
Model:	804.18 W

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG 804.18 W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JUNG Manualer

JUNG ME 5232 Manual

18 Juni 2025

JUNG 834.28 G Manual

18 Juni 2025

JUNG NRSLC0834RT Manual

18 Juni 2025

JUNG CD 5232T3 Manual

18 Juni 2025

18 Juni 2025

18 Juni 2025

18 Juni 2025

18 Juni 2025

18 Juni 2025

18 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MB Quart MBQT-STG3-1 Manual

18 Juni 2025

Newland Speedata FG60 Neptune Manual

18 Juni 2025

Festo DGST-20-30-E1A Manual

18 Juni 2025

Festo SLS-6-5-P-A Manual

18 Juni 2025

Hoshizaki HS-5230 Manual

18 Juni 2025

Gamdias Athena P3 Manual

18 Juni 2025

IOptron iEFW-15 Manual

18 Juni 2025

Mercyu MRU-AD006 Manual

18 Juni 2025

Royal Catering RCGS-1B1600D6 Manual

18 Juni 2025

Keter Darwin 380L Manual

18 Juni 2025