JUNG A 1701 P Manual


Læs gratis den danske manual til JUNG A 1701 P (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om JUNG A 1701 P, eller vil du spørge andre brugere om produktet?

Side 1/4
Universal centre plate
LB Management
Universal centre plate
Art. No. : ..1701..
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Device components
(1) Insert
(2) Frame
(3a) Blind/shutter up / light on, brighter
(3b) Blind/shutter down / light off, darker
(4a) Disabling function
(4b) Memory function
1/4
32595313
J0082595313
01.03.2018
(5) Function LED
Red = Disabling function active
Green = Memory function active
(6) Status LED, green
On = Blind/shutter activated / light switched on
3 Function
Intended use
- Manual and time-controlled operation of Venetian blinds, shutters, awnings or lighting
- Operation of switching, dimming or Venetian blind insert or 3-wire extension from LB
management
Product characteristics
- Activation of blind/shutters, with Venetian blind insert
- Switching and dimming of lighting, with switching or dimming insert
- Ventilation position of the blind/shutter can be saved, with Venetian blind insert
- Switch-on brightness of lighting can be saved, with dimming insert
- Disabling function
- 2 switching times can be saved, which are repeated in a 24-hour cycle
Behaviour after a mains voltage failure
- All saved switching times have been deleted.
- The load is switched off.
- Ventilation position and switch-on brightness remain intact.
4 Operation of Venetian blind and shutters
Moving the blind/shutter
oPress button (3a) or (3b) for longer than one second.
The blind/shutter moves in the desired direction to the end position or stops when the
button is pressed again.
iIf a ventilation position has been saved, the blind stops in the ventilation position when
moving down from the top end position (see Saving the ventilation position).
Adjusting the slats
oPress the button (3a) or (3b) for less than one second.
Saving the ventilation position
To save and execute the ventilation position, the Venetian blind/shutter must be moved to the
upper end position and the status LEDs (6) switch off automatically after 2 minutes.
oFrom the top end position, press the button (3b) for longer than second.
The blind/shutter moves in the lower end position direction.
oPress and hold down the button (3a) and (3b).
The blind/shutter remains stopped, but continues to move after 4 seconds.
oAs soon as the desired ventilation position has been reached, release the buttons and
press the button (3a) within the next 4 seconds.
The ventilation position is saved. The blind/shutter moves back to the upper end position.
iIf the ventilation position is saved again, the old value is overwritten.
5 Operation of lighting
Switch light
oPress button (3a) or (3b) for less than 0.4 seconds.
iWith a dimming insert, the light switches to the brightness that was last set or a saved
brightness.
2/4
32595313
J0082595313
01.03.2018
LB Management
Universal centre plate


Produkt Specifikationer

Mærke: JUNG
Kategori: Ikke kategoriseret
Model: A 1701 P

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG A 1701 P stil et spørgsmål nedenfor, og andre brugere vil svare dig