JUNG TR-SREG Manual

JUNG Ikke kategoriseret TR-SREG

Læs gratis den danske manual til JUNG TR-SREG (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om JUNG TR-SREG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Sunlight/dusk sensor

Use the suction pad to attach the

sunlight/dusk sensor (Diagram



) to the

window pane.

The sunshade function allows you to automa-

tically roll the blinds down when the bright-

ness exceeds a set value. Place the sensor

anywhere on the window pane to determine

the blind’s limiting position.

Application: sunshade for computer work-

stations, sunshade for flowers on windows

sills or in greenhouses etc.

The dusk function allows you to automatical-

ly roll the blinds down when the brightness

falls below a set value. The blinds will be rol-

led down to their bottom limiting position.

You can place the dusk sensor anywhere on

the window pane.

Application: rolling down the blinds when

darkness falls. Only available in conjunction

with the timer cover.

0 - 20 mm

20 mm

Technical data

Sunlight/dusk sensor

Max. sensitivity of

photodiode: approx.

850 nm for λ

Max. amount: 1

Temperature range: –30 °C to +70 °C

Type of protection: IP 54

Glass-break sensor

Glass-break sensors (Diagram



) monitor flat

glass surfaces within a radius of up to 2 m

(depending on glass thickness, frame, putty

etc.). Mechanical vibrations that are too weak

to reach the sensor will not be detected (e.g.

scratching the glass). Window panes with

uneven surfaces (textured or wired glass) and

laminated glass panes muffle vibrations too

much and may therefore not be monitored by

means of broken glass sensors.

Glass-break sensors are very sensitive

devices. Knocking on it or any other improper

treatment may destroy them.

Use a suitable glue (e.g. Loctite Glass-to-Metal

Glue Kit) to attach the glass-break sensor to the

window pane.

Observe the specified distances to the win-

dow frame (Diagram



The blinds will be rolled down to their bottom

limiting position when the glass gets broken.

Application: weather protection if the glass

gets broken.

Technical data

Glass-break sensor

Contact: 1-pole break contact

Switching capacity: max. 350 mW

Transitory resistance:

Idle mode max. 30 Ohm

Alert mode min. 1 MOhm

Alert signal duration: approx. 0.5 – 5 s

Supply line: LIYY 2 x 0.14 mm

Temperature range: –30°C to +70°C

Type of protection: IP 67

Max. amount: 10 (series-connected)









Coupling

Connect the coupling (Diagram



) to the 3-

pole terminal located on the cover with sen-

sor connector or on the insert. The coupling

has two female connectors into which you

plug the male sensor connectors of sunlight/

dusk sensor and/or broken glass sensor.

Technical data

Coupling

Number of sensors: max. 1 sunlight/dusk

to be connected to sensor

the plug-in and max. 1 broken

connector glass sensor

Note

Glass-break sensors may not be used

together with the converter (wind sensor).

The wind protection function via the satellite

input ▲(blind is rolled up) is disabled after

glass breakage, the blind or slats remain

closed.

Sunlight/dusk sensor

Glass-break sensor

Coupling

Decoupling relay

A 93

Decoupling relay TR-S with separate mains

connection

Application example:

Decoupling relays are required if you wish to

use one single blinds controller to operate

several drive units because it is not possible

to connect electrical shutter drives in parallel.

JUNG TR-S can be installed in any 60 mm

wall or junction box.

a = 3 x 1.5 mm

, 230 V ~

b = 4 x 1.5 mm

, 230 V ~

c = 5 x 1.5 mm

, 230 V ~

AZ = junction box

Mains

230 V ~

AZ TR-S

Motor

Ref.-No. 32 SD

Ref.-No. 32 G

Ref.-No. 32 K

Ref.-No. TR-S, TR-S REG

A 94

Wiring diagrams

Decoupling relay

Ref.-No. TR-S, TR-S REG

Technical data

Mains AC 230 V ~, 50 Hz

Control AC 230 V ~, 50 Hz

Capacity 4A, AC 230 V ~,

cos ϕ≥0,8

Operation

The TR-S or the TR-S REG is used for the

simultanous operation of two drives.

For the control all mechanical blinds push-

buttons as well as the motor control inserts

can be used.

Mounting

The TR-S can be installed in a standard

junction wall box.

Mounting

The TR-S REG is a panel mounted device for

a 35 mm DIN rail.

85 mm

39 mm

51 mm

TR-S REG

TR-S

Wiring example

for groupcontrol

M2▼

M2▲

M1▼

M1▲

Z▼

Z▲

M1▼

M2▼

M1▲

M2▲

Z▼

Z▲

Example: 232 ME TR-S terminal TR-S terminal

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Ikke kategoriseret
Model:	TR-SREG
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 Hz
Produktfarve:	Copper colour, Green