Lancom GS-4554X Manual

Lancom Skifte GS-4554X

Læs gratis den danske manual til Lancom GS-4554X (2 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Lancom GS-4554X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

T E C H N I C A L D A T A

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This docu-

ment contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111672/1221

Hardware

Power supply Exchangeable power supply (110-230 V, 50-60 Hz)

Power consumption Max. 82 W

Environment Temperature range 0–40° C; short-term temperature range 0-50° C; humidity 10–90 %, non-condensing

Housing Robust metal housing, 1 HU with removable mounting brackets and slide-in rails,

network connections at front and rear, dimensions 442 x 44 x 440 mm (W x H x D)

Number of fans 2

Interfaces

QSFP+ 2 * QSFP+ 40 Gbps uplink ports for connection to superordinate core switches or content servers, can also

be configured as stacking ports via software

TP Ethernet 36 TP Ethernet ports 10 / 100 / 1000 Mbps

12 TP Ethernet ports 100 / 1000 / 2500 Mbps

SFP+ 4 * SFP+ 1 / 10 Gbps, uplink ports for connection to superordinate core switches or content servers, can

also be configured as stacking ports via software

Console 1 * RJ-45 / 1 * Micro USB

USB 1 * USB host

OOB 1 * OOB

Declaration of Conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with

Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of

Conformity is available at the following Internet address: www.lancom-systems.com/doc

Package Content

Manual Quick Reference Guide (DE/EN), Installation Guide (DE/EN)

Mounting brackets Two 19“ mounting brackets, two slide-in rails for rear stabilization in 19`` racks

Power supply 1x exchangeable power supply LANCOM SPSU-250, expandable to 2 LANCOM SPSU-250 power supplies

(hot swappable, for redundancy operation)

Cables 1 IEC power cord, 1 serial configuration cable, 1 micro USB configuration cable

M O U N T I N G A N D C O N N E C T I N G T H E D E V I C E

Please observe the following when setting up the device

AThe mains plug of the device must be freely accessible.

AFor devices to be operated on the desktop, please attach the adhesive rubber

footpads.

ADo not rest any objects on top of the device and do not stack multiple devices.

A Keep the ventilation slots on the side of the device clear of obstruction.

AMount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.

Both slide-in rails are attached as shown in the accompanying installation instructions

www.lancom-systems.com/slide-in-MI.

APlease note that support for third-party accessories (SFP and DAC) is not provided.

LANCOM GS-4554X

Quick Reference Guide

C ud eadylo -r

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

aConfiguration interfaces RJ-45 & micro USB (Console)

Connect the configuration interface via the included micro USB cable to the

USB interface of the device you want to use for configuring / monitoring

the switch. Alternatively, use the RJ-45 interface with the provided serial

configuration cable.

bUSB interface

Connect a USB stick to the USB interface to store general configuration

scripts or debug data.

You can also use this interface to upload a new firmware.

cTP Ethernet interfaces 10M / 100M / 1G

Connect the interfaces 1 to 36 via Ethernet cable to your PC or a LAN

switch.

dTP Ethernet interfaces 100M / 1G / 2.5G

Connect the interfaces 37 to 48 via Ethernet cable with at least CAT5e / S/

FTP standard to your PC or a LAN switch.

eSFP+ interfaces 1G / 10G

Insert suitable LANCOM SFP modules into the SFP+ interfaces 49 to 52.

Choose cables which are compatible with the SFP modules and connect

them as described in the SFP modules mounting instructions:

www.lancom-systems.com/SFP-module-MI.

fOOB interface (rear panel)

Use an Ethernet cable to connect this out-of-band service port for an IP interface independent of the switching

plane for management tasks or connection to a monitoring server.

gQSFP+ interfaces 40G (rear panel)

Plug suitable LANCOM QSFP+ modules into the QSFP+ interfaces 53 and 54. Select cables suitable for the QSFP+

modules and connect them as described in the SFP modules mounting instructions:

www.lancom-systems.com/SFP-module-MI.

hPower connector (rear panel)

Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific

LANCOM Power Cord.

iAdditional slot for power supply module with mains connection socket (rear panel)

To install an additional power supply module, remove the appropriate module slot cover by loosening both associ-

ated screws and insert the power supply module.

Supply the device with voltage via the power supply module mains connector. Use the supplied power cord (not for

WW devices) or a country -specific LANCOM Power Cord.

To remove a power supply module, disconnect the device from the power supply and pull the power plug out of the

module. Then push the release lever to the left. Now you can pull the module out of the device by the handle J

c ea

gf i

b Reset button

~5 sec. pressed Device restart

7~12 sec. pressed Configuration reset and device restart

e SFP+ ports 1G / 10 G

Off Port inactive or disabled

Green Link 10 Gbps

Green, blinking Data transfer, link 10 Gbps

Orange Link 1 Gbps

Orange, blinking Data transfer, link 1 Gbps

b eca d

a System / Fan / Stack

System: green Device operational

System: red Hardware error

Fan: red Fan error

Stack: green As manager: port activated and connected

with standby manager connected

Stack: orange As standby manager: port activated and

connected to connected manager

g QSFP+ ports 40 G

Off Port inactive or disabled

Green Link 40 Gbps

Green, blinking Data transfer, link 40 Gbps

f OOB port

Off OOB port inactive

Green Link 1000 Mbps

c TP Ethernet ports 10M / 100M / 1G

Off Port inactive or disabled

Green Link 1000 Mbps

Green, blinking Data transfer, link 1000 Mbps

Orange Link < 1000 Mbps

Orange, blinking Data transfer, link < 1000 Mbps

d TP Ethernet ports 100M / 1G / 2.5G

Off Port inactive or disabled

Green Link 2500 - 1000 Mbps

Green, blinking Data transfer, link 2500 - 1000 Mbps

Orange Link < 1000 Mbps

Orange, blinking Data transfer, link < 1000 Mbps

Produkt Specifikationer

Mærke:	Lancom
Kategori:	Skifte
Model:	GS-4554X

Har du brug for hjælp?

Hvis du har brug for hjælp til Lancom GS-4554X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Lancom Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Lancom GS-3628XP Manual

10 Marts 2025

Lancom CS-8132F Manual

7 Oktober 2024

Lancom YS-7154CF Manual

7 Oktober 2024

Lancom IGS-3510XUP Manual

1 September 2024

Lancom XS-5116 Manual

30 August 2024

Lancom GS-1326 Manual

30 August 2024

Lancom XS-5110 Manual

30 August 2024

Skifte Manualer

Nyeste Skifte Manualer

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025

Crestron CLW-LSWEX-2GD Manual

1 April 2025

Vimar 30181.120 Manual

1 April 2025

PureTools PT-MA-HD44DA Manual

1 April 2025