LevelOne IGP-0401 Manual

LevelOne Skifte IGP-0401

Læs gratis den danske manual til LevelOne IGP-0401 (6 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17 anmeldelser. Har du et spørgsmål om LevelOne IGP-0401, eller vil du spørge andre brugere om produktet?

Side 1/6
1
IGP-0401
4-Port Gigabit PoE
Industrial Switch
User Manual
Introduction
This IGP- Industrial port Gigabit Ethernet Switch is equipped with two PoE ports. The PSE ports are 0401 4
critical for your PD environment. They will not only perform your network job, but also provide PSE power
to your PD WiFi or IP CAM applications. This product has been rigorously tested in harsh environment.
These PSE ports can be powered by -56 VDC input voltage. The additional Gigabit TX port and Gigabit 48
SFP port can be easily cascaded to extend your existing networks. With its multi- purpose design, it can
also be Din-Rail or wall-mounted. It is an ideal unit for Mobile Base Station (BTS) IP surveillance, trafc ,
monitoring and security application in critical environment. It can tolerate -40°C to 75°C in harsh
environment to perform reliable network. a
2
Installation package
This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted brackets are included.
Power connection
Wall mount bracket x 2
Din Rail Bracket x 1
This unit provides 6 pin terminal block. The PoE port can be operated from 48-56VDC power source input.
Always make sure your input voltage is within this supported voltage range .
WARNING any exceeded input voltage will not make this unit function and may damage this unit.
This unit comes with 3 power input sources. P1, P2, and P3
To make power connection Follow the printed polarity for P1+, P1-, P2+, P2-, and ground. Connect positive
wire to P1+ or P2+, connect negative wire to P1- or P2-, also connect
neutral wire to the ground screw as shown.
Relay You may use 24V@1A relay connection to your external--
device for special purpose. When 2 powers are connected, the relay
is in OPEN mode. If only one of the power source is connected, the
relay change to SHORT mode. This Relay will only work with andP1
P2. It is independent to P3
Power connecting procedure:
STEP 1 Pull out 6 pin terminal block.
STEP 2 Connect wire to P1+, P1-, or P2+, P2-, and Ground the neutral wire to the ground screw.
STEP 3 Plug back 6 pin terminal block to its place.
Or, Connect the P3 power DIN from external power adopter.
WARNING
Always ground the power source to maintain a clean power input. Due to too many cheap made power
supplies, it creates too much noise, and it will cause the power input uctuates when connect to this unit.
To avoid this, always ground the power source to gain a clean power input.
6 pin Terminal Block p2-x
Philips Head Screw x 4


Produkt Specifikationer

Mærke: LevelOne
Kategori: Skifte
Model: IGP-0401

Har du brug for hjælp?

Hvis du har brug for hjælp til LevelOne IGP-0401 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skifte LevelOne Manualer

LevelOne

LevelOne FSW-0808TX Manual

30 December 2025
LevelOne

LevelOne KCM-0832 Manual

4 December 2024
LevelOne

LevelOne FEP-0511 Manual

3 Oktober 2024
LevelOne

LevelOne FEP-1601 Manual

2 Oktober 2024
LevelOne

LevelOne IGS-2128 Manual

23 September 2024
LevelOne

LevelOne GTL-2891 Manual

10 September 2024
LevelOne

LevelOne FGU-5021 Manual

9 September 2024
LevelOne

LevelOne IFP-0503 Manual

31 August 2024
LevelOne

LevelOne GSW-0507 Manual

31 August 2024
LevelOne

LevelOne GSW-2457 Manual

31 August 2024

Skifte Manualer

Nyeste Skifte Manualer