LiftMaster 050DCRJWFMC Manual

LiftMaster Ikke kategoriseret 050DCRJWFMC

Læs gratis den danske manual til LiftMaster 050DCRJWFMC (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om LiftMaster 050DCRJWFMC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Logic Board

Model 050DCRJWFMC

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-

exempt RSSs. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between

users/bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Before you begin. Your new MyQ® serial number is located on the

replacement label with your replacement logic board. You will need this new MyQ

serial number to connect your opener to the network.

Disconnect power.1. 2. Open the front panel . (A)

Remove the battery cover. 3.

Disconnect the battery. Remove

the battery and set aside .(B)

Add the Step Saver sticker under 4. the yellow program button.

Add the Step Saver sticker under 5.

the yellow program button.

Disconnect the wires coming from

the safety reversing sensors,door

control, door lock and cable

tension monitor from the logic

board (C).

Remove the receiver logic board 6. cover .(D)

Disconnect all the wiring harnesses 7.

from the logic board .(E)

Remove the four screws securing 8. the logic board. Rmove the logic

board , and discard.(F)

Install the new logic board and 9.

connect the wiring harnesses.

Route the antenna through the

channel in the cover.

10. Adhere the new MyQ serial

number label over the original

label on the logic board cover.

11. Reprogram the travel and test the

safety reversal system (see pages

and 3).

12. Program all remote controls and

keyless entries (see page 4)..

13. Use the MyQ app to add the

new MyQ serial number to your

account.

Adjustment

Program the Travel

1. Press and hold the Adjustment Button until the UP Button begins to

ﬂash and/or a beep is heard. The Safety Reversing Sensors will be

disconnected during the Program the Travel process.

2. Press and hold the UP Button until the door is in the desired UP

position.

3. Once the door is in the desired UP position, press and release the

Adjustment Button.The garage door opener lights will flash twice and

the DOWN Button will begin to flash.

4. Press and hold the DOWN Button, until the door is in the desired

DOWN position.

5. Once the door is in the desired DOWN position, press and release the

Adjustment Button. The garage door opener lights will flash twice.

Program the Travel is now complete. If the garage door opener lights

flash 5 times, then programming has timed out and the Travel Limits

have not been set. Please restart the Program the Travel process.

6. To prevent damage to vehicles, be sure fully open door provides

adequate clearance.

Automatic Force Setup

Once both the up and down positions have been manually set, the Safety

Reversing Sensors will reconnect and become operational. Then, the opener

will enter a force-sensing operation by automatically moving the door open

and close. The garage door opener will sound an audible and visual alert

before automatically opening and closing the door. The garage door opener

will beep three times, confirming that the Automatic Force Setup completed

successfully. Adjustment is complete.

If you hear one long beep after the door attempts to move, then the

Automatic Force Set Up has not completed successfully. Please start over at

step 1 of Program the Travel.

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED

by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with

proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST

be tested. Door MUST reverse on contact with 1-1/2" high (3.8 cm)

object (or 2x4 laid flat) on floor.

To prevent damage to vehicles, be sure fully open door provides

adequate clearance.

1. 2.

3. 4.

Adjustment

Button

UP Button

DOWN Button

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	050DCRJWFMC

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 050DCRJWFMC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster SL580 Manual

8 August 2025

LiftMaster HCT12 Manual

7 August 2025

LiftMaster MyQ 827LM Manual

7 August 2025

LiftMaster SL595 Manual

7 August 2025

LiftMaster CAPXSTK Manual

7 August 2025

LiftMaster 66LM Manual

7 August 2025

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025