LiftMaster 041-0405-000 Manual

LiftMaster Ikke kategoriseret 041-0405-000

Læs gratis den danske manual til LiftMaster 041-0405-000 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om LiftMaster 041-0405-000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

BATTERY HOLDER

MODEL 041-0405-000

WARNING

To prevent possible SERIOUS INJURY or DEATH, disconnect

electric power to operator BEFORE installing. ALL electrical

connections MUST be made by a qualiﬁed individual.

CAUTION

To prevent damage to the receiver/logic board, DO NOT touch

printed circuit board of replacement receiver/logic board during

installation.

ALWAYS wear protective gloves and eye protection when changing

the battery or working around the battery compartment.

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm.

Formore information go towww.P65Warnings.ca.gov.

This service kit includes:

• Battery Holder Assembly (1)

• Blank Battery Holder Label

REPLACING THE BATTERY HOLDER

1. Disconnect power.

2. Remove the lower front cover (A).

3. Disconnect and remove the batteries from the battery

compartment (B).

4. Disconnect the wires coming from the safety reversing sensors,

door control, door lock, and cable tension monitor (if installed)

from the logic board (C).

5. Remove the 4 screws securing the battery holder to the main

chassis to remove it (D).

6. Before discarding the old battery compartment, copy the printed

information from the label to the blank label provided on the new

battery compartment.

7. Attach the replacement battery compartment to the main chassis

using the same 4 screws (D).

114-5926-000

LiftMaster

300 Windsor Drive

Oak Brook, IL 60523

LiftMaster.com

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-

exempt RSSs. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between

users/bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

8. Reconnect the wires coming from the safety reversing sensors,

door control, door lock, and cable tension monitor (if installed)

from the logic board (C). Route the long antenna through the

slot in the battery holder (E).

9. Install the batteries and connect the battery connectors (B).

10. Replace the lower front cover on the operator (A).

11. Reconnect power.

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	041-0405-000

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 041-0405-000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster SL580 Manual

8 August 2025

LiftMaster HCT12 Manual

7 August 2025

LiftMaster MyQ 827LM Manual

7 August 2025

LiftMaster SL595 Manual

7 August 2025

LiftMaster CAPXSTK Manual

7 August 2025

LiftMaster 66LM Manual

7 August 2025

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Adventys MO4NL Manual

1 November 2025

Adventys GL 3000 DIR Manual

1 November 2025

Dahua Technology HAC-HFW2241T-Z-A-VP-0622 Manual

1 November 2025

Moultrie Edge Solar Manual

1 November 2025

Dahua Technology XVR5416L-4KL-I2 Manual

1 November 2025

Dahua Technology PFM802P Manual

1 November 2025

EtherWAN EX94000 Manual

1 November 2025

EtherWAN EX87000 Manual

1 November 2025

Techno Line TR-40315 Manual

1 November 2025

Dahua Technology HAC-HFW1239TLM-A-LED Manual

1 November 2025